Filters
Station Controller Accessories
Sierra Radio Systems Universal Relay Control Modules
Sierra Radio Systems Universal Relay Control Modules allow you to control various commercial antenna switches via the system's NodeRed dashboard. This control module can be used to control or emulate the control box for the following antenna switching devices: • 1 of 8 (high side) (DXE-EC-8) • Dual Vertical Array Control Console • BCD Control Console • Pro-Stack Broadband Three Antenna Phasing Relay Unit. • Pro-Stack Broadband Two Antenna Phasing Relay Unit. • CC-8A Control Console • Hi-Z Antenna - 3 Element Array Swtiching • Hi-Z Antenna - 4 Element Array Swtiching • Hi-Z Antenna - 4-8 Pro 8 Element Array Swtiching • Hi-Z Antenna - 8 Element Single Band Arrays
Not Yet Reviewed
$250.00
Sierra Radio Systems 20 Amp DC Power Relays
Sierra Radio Systems 20 Amp DC Power Relays feature Powerpole® Connectors for power in and out, and a 30 Amp relay for remotely switching the power to a device or a series of devices that all consume less than 20 amps. There is an LED to indicate the state of the relay. External connections for 12-volt power in, pull to ground for relay control and voltage measurements are provided via screw terminals. This relay is normally connected to the GPIO module and doesn't feature its own Device Control Network jack. Some assembly is required for this kit. The main board comes assembled with the 8-pin connector, power relay, and LED indicator all soldered to the board. The user will have to solder in the power pole connectors, install the mounting plate and the DIN rail clips. NOTE: While the relay is capable of switching up to 30 amps, the traces on the board are conservatively rated for 20 amps.
Not Yet Reviewed
$29.00
Sierra Radio Systems Station Controller Installation Kits
Sierra Radio Systems Station Controller Installation Kits allow you to mount the components of your Station Controller to a board and will assist in getting the controller up and running. The kit consists of • 2 12 in. long DIN rail mounting brackets • 1 2.5mm flat edge screwdriver for the terminal blocks • 3 12 in. long CAT6 ethernet cables with RJ45 connectors • 1 USB to DCN dongle for RS485 DCN Data.
Not Yet Reviewed
$34.00
Sierra Radio Systems Digital Temperature Sensors
Sierra Radio Systems Digital Temperature Sensors allow you to monitor the temperature of various pieces of equipment and the temperature will be displayed on the Node Red Station Controller Dashboard. Total length is six feet. Comes as a set of two
Not Yet Reviewed
$19.00
Sierra Radio Systems Device Control Network Data and Power Hubs
Sierra Radio Systems Device Control Network Data and Power Hubs provide a way to add devices to your existing Station Controller setup. Featuring five RJ45 DCN modular jacks, and two pair of screw terminals, the Sierra Radio Systems DCN Data and Power Hub allows for up to six more devices to join your Device Control Network (four via RJ45 and two via screw terminals). A 2.1mm barrel jack and a location to mount power poles provide power to the board if not supplied through another device within your Station Controller setup.
Not Yet Reviewed
$29.00
Sierra Radio Systems Slim DIN Mount 6A Relays
Sierra Radio Systems Slim DIN mount Relays are 12 volt single pole, double throw relays that can switch up to 6 amps. These would be useful for remotely switching small ancillary devices in the shack. An LED indicator indicates the status of the relay and is visible when the relay is mounted to the DIN Rail.
Not Yet Reviewed
$12.00
Sierra Radio Systems 900MHz Data Radios
Sierra Radio Systems 900MHz Data Radios allow you to extend your Device Control Network. To use it simply connect the A, B and Ground wires to the system terminal on any station control module. Unlike the rest of the Station Controller modules, the data radio requires a dedicated power connection of 12 VDC via it's 2.1mm barrel connector.
Not Yet Reviewed
$120.00
PXdragon Panel Mount for DR-9400 Modem
The PXdragon Panel Mount for the DR-9400 Modem PXN-40170 enables clean, flush installation in stationary or mobile environments. Designed to replace the original front bezel, it provides additional mounting points for a secure, vibration-resistant fit. The recessed design protects the modem from mechanical impact while maintaining full access to all controls and connectors. Precision CNC milled from black anodized aluminum, the panel mount offers a professional, rugged appearance ideal for radio shacks, vehicles, maritime installations, and emergency communication cases. Installation is quick and straightforward, requiring only removal of the original front panel. Optional sealing tape can be added to enhance dust and splash water protection for demanding field or marine use. PXN-40170 Technical Specifications • Product type: Panel mount / front bezel replacement • Compatible device: PXdragon DR 9400 Modem • Mounting method: Flush panel mount, front installed • Outer dimensions: 6.220 × 2.283 in. (158 × 58 mm) • Material: CNC milled aluminum • Surface finish: Black anodized • Mounting features: Additional mounting holes for secure, vibration resistant installation • Bezel interchangeability: Fully interchangeable with original DR 9400 front bezel • Connector accessibility: Full access to all front facing controls and connectors • Mechanical protection: Recessed design to reduce impact and connector strain • Environmental enhancement: Optional sealing tape support for improved dust and splash water resistance (no IP rating specified) • Installation type: Tool assisted, direct replacement of factory front panel • Application environments: Stationary installations, vehicles, maritime use, emergency and field communication cases
Not Yet Reviewed
$80.99