Wire Antennas for Amateur Radio

Par EndFedz® Antennas

Par EndFedz® Antennas are End Fed Half Wave (EFHW) antennas with the match box coax connection at the end of the wire, for convenient and quick stealth portable operations. These single-band and multi-band antennas can be mounted horizontally, vertically, or as a sloper. No ground plane or counterpoise is needed so portable operation could not be easier. Simply hang the far end from a tree limb or send the wire out a hotel room window or balcony. You can use a telescoping fiberglass mast to get the antenna really high in the air and the supplied end insulators the installation easy. Stealth operation in CC&R and HOA antenna restricted locations is simplified. Their all-black construction makes them difficult to see. Each Par EndFedz® features a UV-resistant black ABS plastic housing with a support rope attachment hole that encloses a matching network to allow the antenna to be fed with standard 50 ohm coaxial cable with a PL-259 (UHF male). All hardware is stainless steel and the SO-239 (UHF female) connector is silver plated and has a PTFE dielectric. The antenna wires are either 18 or 26 AWG stranded Copperweld® with 200 pound breaking strength and a tough, 100% UV stable black polyethylene jacket. One end of the antenna wire has a #10 solder lug making attachment to the matching network feedpoint simple and easily replaceable, if necessary. Standard single and multi-band versions handle 100 or 200 watts and higher power versions handle 300 watts. Lightweight QRP PolyStealth models handle 25 watts and are ideal for portable operation because they are lightweight; the MKII model weighs only 8 ounces and the Trail Friendly model weighs only 3.5 oz. Par EndFedz® Antennas require no counterpoise or extra conductors. The EF-ALLBAND-KW model, about 133 ft. in length, covers eight bands, 80 through 10 meters. The ALLBANDKWJR is 74 ft. in length and operates on five bands, 80-10 meters. The 64 ft. EF-40-10-KW operates on four bands. All three models handle up to 1000 watts SSB/CW and 250 watts AM/Digital Modes. The need for an external tuner may vary based on the antenna model selected and the desired operating band. The manufacturer refers to these antennas as "End-Fed Dipoles" based upon the assertion that a "half-wave radiator is a dipole." This is a variant of the classic definition of a dipole which is a center-fed antenna with two radiating legs running in opposite directions from the feed point. Additional claims about the EFHW state that end feeding a half-wave "can energize the radiator 'nearly' as well as a center-fed." Recent anecdotal measurements indicate that the EFHW radiates about 70% as well as a traditional center-fed dipole. More information is available at each Par EndFedz® model listed below. Order yours from DX Engineering.

4.7 out of 5 stars ( 230 )

$44.99

—

$189.95

PackTenna EFHW2010 End Fed Half Wave Wire Antennas

PackTenna EFHW2010 End Fed Half Wave Wire Antennas are Compact, lightweight trail-ready portable HF antenna systems optimized for the 20m and 10m bands, with optional 40m support via an add-on wire element. Designed for field use like POTA, SOTA, and backpacking, this antenna system comes with an integrated wire winder, matching transformer, and antenna wire into a single rugged unit that won't take up a lot of space in a backpack.

4.29 out of 5 stars ( 7 )

$115.00

Buckmaster OCF Dipole Antennas

Buckmaster OCF Dipole Antennas are made from the best quality materials with a completely potted waterproof balun and no external connectors. They are designed to give you years of trouble-free service! Buckmaster antennas are shipped fully assembled, ready to deploy with no tuning or trimming required. Choose a model with a 300 watt balun or a 3,000 watt balun. Each has a weather protected SO-239 connector. They are offered in three lengths to operate in these bands: - 270 ft. models cover 160, 80/75, 40, 20, 17, 12, 10, 6 meters - 135 ft. models cover 80/75, 40, 20, 17, 12, 10, 6 meters - 68 ft. models cover 40, 20, 10 and 6 meters Classic OCF (Off-Center Fed) antennas, like Buckmaster, typically have the feedpoint at the 2/3 and 1/3 point on the overall half-wave wire antenna. That means one leg is twice as long as the other. They are intended to be installed with the feedpoint at 35 ft. and the ends at about 15 to 25 ft. However, other installations such as a horizontal "flat top" can work very well. A tuner may be required for best SWR. Buckmaster OCF Dipole Antennas are a very simple way to get on the air and work multiple bands… quickly! They are a great choice as a first antenna or as a supplement to others. Order your Buckmaster OCF Dipole from DX Engineering.

4.88 out of 5 stars ( 65 )

$276.00

—

$544.00

Alpha Delta Parallel Dipole Antennas

Alpha Delta Parallel Dipole Antennas consist of the Alpha Delta DELTA-C center insulator and end insulators, ISO-RES coils connected to the 80/40/15 meter wires, and separate wires for 20 and 10 meters. All wires are assembled to the center insulator and utilize stainless steel hardware and 12-gauge solid copper wire. These antennas are shipped fully assembled, except for threading the 20 and 10 meter wires through the parallel wire element spacers. These are inserted during the antenna final assembly and installation process. * Model DX-EE covers 40, 20, 15 and 10 meters * Model DX-CC covers 80, 40, 20, 15 and 10 meters * Model DX-LBPLUS covers 160, 80, 40, 20, 15 and 10 meters Overall length for the DX-CC is 82 ft., 100 ft. for the DX-LBPLUS, and the DX-EE is only 40 ft. in length overall. An antenna tuner is required for 15 meter operations on each of these antennas. Alpha Delta Parallel Dipole Antennas provide lots of bang for your buck! Order from DX Engineering!

4.58 out of 5 stars ( 48 )

$195.99

—

$245.99

PackTenna PT-101 Mini End-Fed Random Wire Antennas

PackTenna PT-101 Mini End-Fed Random Wire Antennas are Compact, lightweight trail-ready portable HF antenna systems ideal for POTA, SOTA activations, camping, backpacking, and travel. The PackTenna Mini Random Wire Antenna combines a 9:1 UNUN, wire winder, and antenna wire in a compact unit that is quick to set up and take down and toss into a backpack. The antenna comes with 29 feet of 26AWG copper clad steel wire with a great "silky" jacket to minimize wire tangle. You can cut the wire to fit your needs. Typically, a length that is not a multiple of a quarter wave on any ham band is best. This antenna requires a wide antenna tuner and is rated to handle 100 watts SSB/CW, 50 watts digital. While there are exceptions, the built-in tuner on most radios (Icom, Kenwood, Yaesu) are typically narrow range tuners that can handle a range from 25-150 ohms. This is not wide enough to handle all conditions.

5.0 out of 5 stars ( 2 )

$110.00

Alpha Delta Single Wire Multi-Band Dipole Antennas

Alpha Delta Single Wire Multi-Band Dipole Antennas consist of the Alpha Delta DELTA-C Center Insulator, end insulators, and an ISO-RES coil connected to the 80/40 meter wires. The wires are attached to the center insulator. These antennas are shipped fully assembled and ready to install. They utilize stainless steel hardware and 12-gauge solid copper wires. Their overall length is 82 ft. for the DX-DD and 100 ft. for the DX-LB Plus. Due to their Hi-Q construction, bandwidth on 80 meters is 65 to 70 kHz. A wide range antenna tuner is required for greater frequency coverage on 80 meters. These are a great value in multi-band dipoles for the lower frequencies. Order Alpha Delta Single Wire Multi-Band Dipole Antennas from DX Engineering and hit the airwaves!

4.53 out of 5 stars ( 32 )

$179.99

—

$209.99

Alpha Antenna JPole SR HF Multi-Band EmComm End-Fed Antennas

Alpha Antenna JPole SR HF Multi-Band EmComm End-Fed Antennas are designed to offer coverage across a across a wide frequency range. These 60ft. long End-Fed antennas cover the Amateur bands 160-10 meters. An external tuner is necessary for improved SWR across the frequency range, although bandwidth is limited on the 80M band. The Alpha Antenna JPole SR HF Multi-Band EmComm End-Fed Antennas are ideal for EmComm and other portable operations such as POTA and SOTA, providing reliable performance for both near and distant HF communications.

4.33 out of 5 stars ( 3 )

$219.00

Moonraker G5RV Wire Antennas

Moonraker G5RV Wire Antennas have gained popularity as one of the most widely used multi-band antennas worldwide and deliver good overall performance on most HF ham bands when paired with an external tuner. These G5RV antennas feature a high-quality SO-239 molded socket at the end of the ladder line. This design offers a significant advantage by allowing the use of coaxial cable as the entry feedline to your radio equipment. However, it's important to note that some internal tuners may not have the range required to properly tune this antenna.

4.29 out of 5 stars ( 7 )

$71.99

—

$150.99

Alpha Antenna JPole JR HF Multi-Band EmComm End-Fed Antennas

Alpha Antenna JPole JR HF Multi-Band EmComm End-Fed Antennas are designed to offer coverage across a across a wide frequency range. These 34ft. long, End-Fed antennas cover the Amateur bands 80-6 meters. An external tuner is necessary for improved SWR across the frequency range, although bandwidth is limited on the 80M band.

Not Yet Reviewed

$199.00

Alpha Delta Single Band Full Size Dipole Antennas

Alpha Delta Single-Band Full Size Dipole Antennas are pre-assembled half-wave monoband dipole antennas. They are pre-tuned for the lowest indicated frequency and come with the correct amount of mounting rope. These antennas may be tuned for any frequency by shortening the wire lengths according to the supplied instructions. Cut their DX-80 for 60 meters, their DX-40 for 30 meters, and their DX-20 for 17, 15, 12 or 10 meters. They are constructed with a Delta-C Center Insulator with built-in SEP static electricity protectors and are fully assembled using stainless steel hardware, 12-gauge PVC-insulated high-strength solid copper wire, and DELTA-CIN End Insulators. Their center insulators feature SO-239 (UHF female) connectors to accept the PL-259 on your coaxial cables. These antennas will easily handle full legal power. For quality monoband dipoles you can depend on, order Alpha Delta Single-Band Full Size Dipole Antennas from DX Engineering!

4.95 out of 5 stars ( 40 )

$90.99

—

$119.99

DX Engineering Off Center Fed High Power Dipole Kits

DX Engineering Off Center Fed (OCF) dipole wire antenna kits use two different lengths of antenna wire (dipole legs) to achieve operation on the HF bands. A slightly elevated SWR is the trade-off for a single wire antenna that covers multiple bands efficiently. On most bands, the internal tuner in modern transceivers will match the antenna feedline when the SWR is 3:1 or less. On frequencies where the SWR is above 3:1 SWR, an ATU external to the rig may be needed. DX Engineering Off Center Fed Dipoles are designed to be rugged yet lightweight, and handles 1,500 watts SSB and CW. These kits include two lengths of premium 14 gauge relaxed PVC antenna wire, each with a ring terminal soldered on one end; one DXE-MC20-C4-1 DX Engineering Maxi-Core® 4:1 Dual Core Balun (with SO-239); the DXE-WA-BMB Dipole Center Insulator Mounting Bracket for Maxi-Core® Balun including End Insulators; and Stainless Steel hardware. Add supports, coax and rope to your order for a complete multi-band antenna installation.

Not Yet Reviewed

$231.97

—

$243.97

DX Engineering 8040 NVIS Antennas

DX Engineering 8040 NVIS Antennas: Near Vertical Incidence Skywave (NVIS) is a propagation mode which uses high-angle radiation that sends signals almost straight up! They are then reflected back to Earth for very effective short to medium distance communications that works virtually every day and into the evening. NVIS dipoles are almost Omni-directional and their height requirement is for the feedpoint to be at only 15 feet above the ground! These 80 and 40 meter wire antennas work very well with their feedpoint at only 15 feet above the ground, supported by the included mast, or your own non-metallic support. The ropes tied to the wire dipole end-insulators are used as guys for the support mast, and are secured to the ground with four tent pegs. DXE-NVIS-8040S and the DXE-NVIS-8040 antenna kits are complete with everything required; the fiberglass mast (four, 4 ft. sections that extend to 15 ft.), a DX Engineering Maxi-Core® 20 1:1 Balun, model DXE-MC20-1-1T, a balun mounting kit, coax strain relief bracket, antenna wire, insulators, four tent pegs, rope, and a 100 ft. RG-8X coax assembly with PL-259s! The four legs of the antenna, each deployed 90 degrees apart, provide the mast guying. DXE-NVIS-8040SNM and the DXE-NVIS-8040NM antenna kits are exactly the same kits with everything except the 15 ft. fiberglass mast. Use your own non-metallic mast or hang the feedpoint 15 ft. above the ground from the limb of a tree. The DXE-NVIS-8040S and DXE-NVIS-8040SNM are shortened NVIS wire antenna kit version that features loading coils to make the 80 meter dipole legs the same length as the 40 meter dipole legs, 34 ft., so this antenna fits into a square area that is only about 50 ft. by 50 ft. The DXE-NVIS-8040 and DXE-NVIS-8040NM are full size, with 67 ft. wire dipole antenna legs for 80 meters and 34 ft. legs for 40 meters and it fits into a rectangular area approximately 100 ft. by 50 ft. NVIS rarely works at frequencies outside the range of 2 MHz to 10 MHz. The signal must penetrate the D layer of the ionosphere and bounce off the F layer. Signals on frequencies below 2 MHz will not penetrate the D layer; frequencies higher than 10 MHz will not bounce off the F layer at these sharp angles, they penetrate and continue out into space. Regular-height dipoles or vertical antennas have a lower take off angle and your signal may be heard three states away, but not in your own state due to the "skip zone." This skip zone is the area between the maximum ground wave distance and the shortest sky wave distance where no communications are possible. Depending on operating frequencies, antennas, their height above ground and propagation conditions, this skip zone can start at roughly 10 to 20 miles away and extend out to several hundred miles. NVIS mode of operation makes it ideal for in-state and next state communications during disasters or other emergency situations. The military has used NVIS techniques for decades to provide short haul communication with other units on the ground. This is why these antennas are ideal for round-table gatherings with regional ham friends on 40 and 80 meters, day to day and night after night. These antennas are easy to deploy and are great for camping, RVs, QRP, ARES, EMCOMM, State QSO Parties and Parks On The Air (POTA) and any other uses where short range HF operation on 80 or 40 meters is desirable. They are actually pretty stealthy, too! Due to their near vertical radiation, NVIS dipoles are almost Omni-directional. They even have a legal-limit power rating! Remember, Amateur Radio operators look to 80 and 40 meters for short skip NVIS operations. Order DX Engineering 8040 NVIS Antennas and fill in the skip zone!

4.67 out of 5 stars ( 6 )

$426.38

—

$656.86

Momobeam Multiband End Fed Wire Antennas

Momobeam Multiband End Fed Wire Antennas are the perfect HF solution for amateur radio operators seeking simplicity, versatility, and performance. Designed for both fixed and portable operation, these multiband antennas can be deployed quickly in horizontal, inverted L, or sloper configurations—ideal for operators on the go. Covering the 80–10m or 40–10m amateur bands (depending on the model) and delivers reliable multiband performance. Built to last, these end-fed wire antennas feature stainless steel hardware and UV-resistant materials for long-term durability. At their core is a coated copper wire radiator paired with a 49:1 impedance transformer, ensuring efficient 50-Ohm operation across the entire operating range. Rooted in the rich history of end-fed technology—dating back to the Zepp antennas used on Zeppelin airships during World War I—these antennas combine proven design principles with modern engineering for unmatched versatility. Whether you're a beginner or a seasoned operator, Momobeam Multiband End Fed Wire Antennas are your go-to solution for dependable HF performance.

5.0 out of 5 stars ( 2 )

$159.99

—

$313.99

ICOM AH-710 Folded Dipole Antennas

ICOM AH-710 Folded Dipole Antennas get you on the air--fast! You can cover all amateur bands and operate with up to 150 watts with these ICOM pre-assembled, multi-band folded dipole antennas. Designed to work with any ICOM amateur HF transceivers, including their marine transceivers, the AH-710 antennas can be installed in flat top or inverted V configurations. The specs for ICOM AH-710 folded dipole antennas are: * Frequency range: 1.9 to 30 MHz * Power rating: 150 W * Input impedance: 50-ohm connection * VSWR: Less than 2:1 (1.9 to 18 MHz) Less than 2.5:1 (18 to 30 MHz) * Length: 24.5 m (80.4 ft.) * Coaxial feed line: 30 m (98.4 ft.) with PL-259s * Support Rope: 10 m (32.8 ft.) white Nylon * Auto-bonding Tape: 30 cm ( 1 ft.)

4.77 out of 5 stars ( 13 )

$429.99

Kelemen Monoband Dipoles

Kelemen Monoband Dipoles are high-quality, preassembled wire antennas featuring full-size models and a few shortened low-band models with coils for lengths that are easier to fit in the yard. Kelemen Dipoles are rugged; strong but lightweight, with good stability and excellent longevity. The included balun is intentionally not potted watertight to save on weight, instead using effective weep holes. Maximum power handling depends on each model's balun or coil used on shorter antennas. Kelemen Dipoles are pre-tuned to the lower end of the band (CW) because they are easily shortened for use on the phone (SSB) end of the band. Monoband dipoles are the simplest and most efficient type of dipole. Depending on the availability of supports, the Kelemen Dipole can be suspended in different ways and achieve different directional characteristics depending on the height. As an inverted-V set up close to the ground, it is an ideal omnidirectional antenna with strong high-angle radiation which is good for local traffic. The higher the dipole hangs, the flatter the radiation, and the better the chances for DX. Due to the light construction of the Kelemen dipoles, the requirements for the supports are not very high. For example, with inverted-vee setups, a push-up mast is usually sufficient as a mast. With horizontal suspension, a small tree with a pulley can often be used as a support point. Insulators and center hooks are included with each preassemble Kelemen Dipole antenna. For installation, use lengths of non-conductive antenna rope for the center support and for each end of the dipole. Order Kelemen Monoband Dipoles in North America exclusively from DX Engineering.

4.33 out of 5 stars ( 12 )

$129.99

—

$279.99

DX Engineering TWIG End Fed Half Wave QRP Antenna Kits

DX Engineering TWIG End Fed Half Wave QRP Antenna Kits include the essential components needed to build a lightweight, low-power (QRP) end-fed half-wave antenna for portable and field operations. Ideal for activities such as POTA® and SOTA™, these kits are designed for quick deployment, efficient operation, and minimal equipment requirements. When properly assembled and tuned, TWIG End Fed Half Wave QRP antennas deliver an SWR of less than 2:1 without the need for an antenna tuner and are rated for 25 watts SSB, 10 watts CW, and 5 watts digital modes. At the heart of these kits is a 49:1 transformer that matches the high feedpoint impedance of the half-wave radiator to a standard 50-ohm coaxial feedline. The integrated BNC female connector is compatible with recommended coaxial cables and most QRP transceivers. Once the included antenna wire is properly tuned for the desired operating band, an external tuner is typically unnecessary, reducing pack weight and simplifying field operation. No separate counterpoise wire is required, as the coaxial feedline serves this function when installed correctly. To simplify assembly and deployment, the kits feature a built-in quick-connect wire terminal designed for use with the included 24 AWG antenna wire. Two end insulators and attachment clips are also included to provide secure strain relief and convenient field installation. A DX Engineering wire winder and reusable Bongo ties help keep the antenna organized and compact when stored or transported. A typical installation uses a sloper configuration, with the feedpoint positioned approximately 6 to 7 feet above ground level and the antenna wire extending upward to a height of 25 to 30 feet. For optimum performance, a 25- to 35-foot coaxial feedline with BNC connectors is recommended. An optional DXE-LPFC-BNC Feedline Choke installed at the transceiver end of the coax is also recommended to help minimize common-mode current. While the antenna can be deployed in a variety of configurations, final wire lengths may vary depending on the installation method and operating requirements. User assembly is required. Recommended tools and materials include wire cutters, a tape measure, 3/16-inch diameter rope to hang the antenna, electrical tape, a suitable throwing weight for antenna installation, and an antenna analyzer for trimming and tuning the antenna element to the desired operating band.

Not Yet Reviewed

$77.99

EAntenna Multi-Band Dipole Wire Antennas

EAntenna Multi-Band Dipole Wire Antennas come in single wire and parallel-wire types. Those with multiple wire elements come with special spacers to keep the dipole elements separated. All are supplied with 1.5 kW PEP balun with SO-239 coax connector. A variety of models are available including 80, 40 20, 15 and 10 meters, or 40, 20, 15 and 10 meters, a 20, 15 and 10 meter model, a two-band model for 80 and 40 meters and a special 30, 17, 12 and 6 meter model. They are made with top quality components to offer long service and excellent operational results. Featuring high strength polycarbonate insulators, you can depend on excellent multi-band operations with EAntenna Multi-Band Dipole Antennas. NOTE: Manuals are normally supplied in Spanish and English. If your manual doesn't have an English section, please contact DX Engineering for an English version.

3.97 out of 5 stars ( 34 )

$289.99

—

$349.99

CHAMELEON ANTENNA Base HF SKYLOOP 2.0 Antennas

CHAMELEON ANTENNA Base HF SKYLOOP 2.0 Antennas are the next iteration of extreme-performance horizontal antennas. SKYLOOP 2.0 antennas are comprised of 265 feet of wire, insulators, hardware and a matching transformer. Their integral impedance matching transformer allows broadband antenna tuning. These antennas will operate from 3.5 - 54 MHz (80 through 6-meter amateur bands) without any physical adjustment by simply employing a wide-range antenna tuner. Their low visual impact also makes them a good choice for hams living in developments with homeowners associations, deed restrictions or any hams that need stealthy antennas. They are also outstanding shortwave listening (SWL) antennas. CHAMELEON SKYLOOP 2.0 specifications: * Frequency: 80 - 6 meters * Power handling: 250 W CW or 500 W SSB * RF Connection: UHF female on impedance transformer * VSWR: Antenna tuner required * Length 265 ft. CHAMELEON SKYLOOP 2.0 antenna systems consist of: * One matching transformer * 265 ft. antenna wire * Two isolation loops * One carabiner * Three insulators CHAMELEON ANTENNA Base HF SKYLOOP 2.0 Antennas are well built antennas that will satisfy your need for a stealthy HF multi-band capable antenna system. Order CHAMELEON ANTENNA Base HF SKYLOOP 2.0 Antennas from DX Engineering and listen to the world!

5.0 out of 5 stars ( 3 )

$299.00

On Sale

Kelemen Trap Dipole Antennas

Kelemen Trap Dipole Antennas are high-quality, heavy-duty pre-assembled wire antennas intended for permanent installations. They feature special traps made with of PTFE (Teflon®) insulated coax for high Q and low losses, offer high performance multi-band operations—and are excellent shortened antennas where there's not enough space for a full-size dipole. Kelemen Trap Dipole Antennas include a series of monoband models, as well as a series of multi-band models that cover an extensive combination of HF bands from 160m through 10 meters. Specific models handle either 400 watts, 1,000 watts or 2,000 watts PEP SSB and CW at resonance. Kelemen Antennas are fully temperature-resistant and weather-proof, and are manufactured from high-quality materials. Balun cases are constructed of transparent, weather-proof polycarbonate with a bottom-mounted SO-239 (UHF female) connector. Hardware and clamps are all stainless steel. Each antenna is completely assembled with the balun, clear PVC-insulated stranded copper wire, stainless wire clamps and egg insulators, ready for operation. Just add rope and coax to complete your Kelemen wire antenna installation. Kelemen Trap Dipole Antennas may be mounted horizontally or in an Inverted-Vee configuration with a central support required. Many Kelemen Antennas are perfect for portable operations because of their low weight. Their coaxial traps are much lighter than conventional traps, making it easier to keep the antenna at an effective height. In many cases they can be easily supported by a single fiberglass pole. For base operations, these antennas should be placed high, in an unobstructed location well away from buildings to limit shifting of resonant frequencies. Kelemen Antennas are often the best possible antenna choice for full-time base operations, offering the advantages of specialized multi-band coverage that perfectly complements the other antennas of the station. Order Kelemen Antennas in North America exclusively from DX Engineering.

4.62 out of 5 stars ( 29 )

$339.99

$159.99

—

$549.99

DX Engineering Multi-Band Dipole Antennas

DX Engineering Multi-Band Dipole Antennas are designs that are rugged, yet lightweight. Using a tuner, they are usable to 30 MHz and come complete with the wire elements, ladder feedline, center T support, and end mount brackets. These antennas are built using the highest quality components. They use 14 AWG stranded-copper, PVC jacketed elements for flexibility and strength and 100 ft. of 18 AWG 300-ohm 0.88 Velocity Factor ladder lines that are UV-resistant. Stainless steel hardware is included. Often, a 4:1 balun is suggested for multi-band dipoles; however, the best balun to use for this application is a 1:1 ratio. The 1:1 baluns provide better balance, have lower loss, and are more tolerant to load impedance and balance variations than other baluns. A tuner balun is not included in the dipole antenna kits and is available separately. The dipole center T support has pre-drilled holes for the attachment of the wire elements, feedline, and support or messenger lines. The center support top hole is used for the attachment of a "messenger line" that can be strung above the antenna wire and is used to provide support for the antenna wire and feedline. The use of the messenger line, which is strongly recommended but not included, will reduce the stress on the element wires and keep the antenna from stretching over time, which will change its resonant frequency. This line can be thin Synthetic Textile rope available from DX Engineering, which has a high breaking strength. Ideally, it should attach to the same structure used for the dipole, only above it, forming at least a 30 degree angle between the dipole and the messenger line. For further information and to decide the amount of rope you will need, please read the included instructions and check your wire antenna area of construction. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you lack the room for more than one antenna or need a multiband antenna for band agility, consider one of these DX Engineering Multi-Band Dipole Antennas as an elegant and economical solution!

4.87 out of 5 stars ( 30 )

$93.99

—

$125.99

Bushcomm BBA-1KD Kilowatt Multi-Wire Broadband Antennas

Bushcomm BBA-1KD Kilowatt Multi-Wire Broadband Antennas are in Bushcomm's flagship antenna group (BBA Series) and are all-round best performers. These antennas are highly efficient and engineered to meet the exacting standards of professional and commercial users. BBA-1KD 80 through 10 meter dipoles are significantly more compact than their 160 meter counterparts. Bushcomm BBA Series antennas have the flexibility to suit a wide range of installation situations - between two purpose built towers, in an inverted "V" configuration or even between a tower and the shed out back. All BBA Series antennas include a purpose-designed balun. BBA-1KD specifications: * Frequency Range 3.5 - 30MHz * Nominal Input Impedance 50 Ohm * VSWR (typical) Better than 2:1 * Gain (height dependent) 5dBi (typical) -4dBi at 3.5MHz (height dependent) * Power Rating 1,000 Watts continuous 1.5 kW PEP (voice) * 1kW digital ready * Input connector UHF Type socket (SO-239) * Operating Temperature -22 degrees F to 122 degrees F * Storage Temperature -40 degrees F to 185 degrees F * Antenna Weight: approximately 11.0 lbs. * Antenna Length: 85.58 ft. * Radiating elements 0.079 in. (14AWG) Stainless Steel (304) * Wind rating 130mph (horizontal) * Ice loading 0.25 in., (with reduced wind rating) * Mast Spacing 95 ft. horizontal tower spacing; 65.6 ft. footprint inverted V Note: When the "Documentation" tab is available, please look at the associated files for additional product information. The highest quality materials are used in construction of these antennas including stainless steel wire and fittings and UV resistant fiberglass rods. Quality materials and excellent design produces an antenna that will survive the rigors of the outdoors for many years. For a broadband 80-10 meter dipole, remember these Bushcomm BBA-1KD Kilowatt Multi-Wire Broadband Antennas from DX Engineering.

5.0 out of 5 stars ( 1 )

$2,089.99

DX Engineering Single-Band Dipole Antenna Kits

DX Engineering Single-Band Dipole Antenna Kits are one of the best low-cost HF antenna options available for Amateur Radio operations or Shortwave Listening (SWL). These high-quality wire dipole antenna kits are lightweight, rugged and easy to construct. Wires are supplied long so any frequency of the desired band can be cut to resonance or lowest SWR. Add antenna rope and coaxial cable to put up and connect your dipole antenna. Your dipole can be installed horizontally between supports or as an Inverted-Vee with the center feedpoint on the highest support; see instructions for details. From the kits listed, select the model that covers the HF band desired. Then cut the supplied wire to the dimensions in the manual for that band and assemble. Having been a proven type of antenna for decades, wire dipole antennas will get you on-the-air either from your home QTH or at a portable operating area. Order a DX Engineering Single-Band Dipole Antenna kit and enjoy efficient and reliable HF communication! DX Engineering Single-Band Dipole Antenna Kits include: - Premium 14 AWG Stranded Copper, Relaxed PVC Antenna Wire, one end 1/4 in. ring terminals - DXE-MC20-1-1 DX Engineering Maxi-Core® 1:1 Balun - DXE-WA-BMB Wire Antenna Balun Mounting Bracket and End Insulators: High-Strength UV Resistant Black Polyresin Compound - Stainless Steel Hardware - Instruction Manual Power Rating - Up to legal limit of 1.5 kW using the included DX Engineering DXE-MC20-1-1 MaxiCore® 20 Balun. Limiting factors will be the height above ground and physical location. Note: For more details on antenna design, feedline and radiation angles, consult a reliable text such as the ARRL Antenna Book.

5.0 out of 5 stars ( 3 )

$227.46

—

$252.96

DX Engineering Low Power Portable Dipole and Winder Kits

DX Engineering Low Power Portable Dipole and Winder Kits supply the parts for a fun DIY build of a lightweight resonant HF antenna. They are designed for fast portable operations on 40 meters or higher frequency bands. Making your own Single Band or Dual Band Linked Dipole is easy and fun, especially because once they are built, they are designed to repeatedly and quickly unwind, install, make contacts on the air, wind up and go! Typically set up as an Inverted Vee, DXE-LPB1-DWHF series portable dipoles are a perfect match for DX Engineering Nomad Portable Telescopic Masts (sold separately). Great for POTA, SOTA and JOTA, here are some of the best, low-cost DIY antenna kits available for 'on-the-go' amateur radio. Here's what comes in the lightweight DX Engineering Low Power Portable Dipole and Winder Kits: • Center Insulator with a 1:1 Low Power Balun, 50-ohm (max. RF power 250 watts PEP SSB, 100 watts CW or Digital); BNC female right-angle connector pre-installed. • 24 Gauge Stranded Hi-Visibility Yellow Insulated Wire; 80 feet, Two 40 ft. sections. • 4 Link Insulators support the wire and may be used to "break up" the dipole into multiband sections. • 4 Alligator Clips are used two per link, one link per side makes a two band dipole. • 4 Clip Hooks for user supplied rope. • 1 Snap Hook to support the Center Insulator Balun on a Nomad Portable Mast • 3 easy to hold DX Engineering Red Winders for the portable dipole wires and user supplied coaxial cable; Winders have notches and holes for a variety of uses. • One bag of Bongo Ties (available in variety of colors) to secure wires onto Winders. Resonant, low-SWR operation is accommodated on two bands by adding a pair of Band Links. Changing bands is done easily by linking or unlinking pairs of clips on opposite sides of the dipole. With the center of the antenna at 15 to 20 ft. high, and the ends of the dipole a few feet above the ground, the links are easy to reach. Additional band link kits (DXE-LINK-KIT) are available separately to create multiband linked dipole antennas. Each optional Link Kit has the parts for one additional band and contains 2 insulators, 4 'gator clips and 4 clip covers. The Center Insulator 1:1 Balun feedpoint BNC is easily connected with super thin DXE-174VDB or special adapter DXE-8XVDXB DX Engineering Hi-Visibility Orange Coaxial Cables, available in various lengths. Set up at a park or other portable operating site quickly! Get DX Engineering Low Power Portable Dipole and Winder Kits and build up a new pastime!

5.0 out of 5 stars ( 1 )

$84.99

Bushcomm BBA-1KDE Kilowatt Multi-Wire Broadband Antennas

Bushcomm BBA-1KDE Kilowatt Multi-Wire Broadband Antennas are in their flagship antenna group (BBA Series) and are all-round best performers. These antennas are highly efficient and engineered to meet the exacting standards of professional users. Bushcomm BBA Series Antennas have the flexibility to suit a wide range of installation situations - between two purpose built towers, in an inverted "V" configuration or even between a tower and the shed out back. All BBA Series antennas include a purpose-designed balun. BBA-1KDE specifications: * Frequency Range 1.6 - 30MHz * Nominal Input Impedance 50 Ohm * VSWR (typical) Better than 2:1 (with 30m RG-213) * Gain (height dependent) 5dBi (typical) -5dBi at 1.8MHz (typical, 130 ft. height) * Power Rating 1,000 Watts continuous 1.5 kW PEP (voice) * Input connector UHF Type socket (SO-239) * Operating Temperature -22 degrees F to 122 degrees F * Storage Temperature -40 degrees F to 185 degrees F * Shipping 57 x 15.7 x 8.7 in., approximately 35 lbs. * Antenna Length 177 ft. * Radiating elements 0.079 in. (14AWG) Stainless Steel (304) * Wind rating 130mph (horizontal) * Ice loading 0.25 in., (with reduced wind rating) * Mast Spacing 183 ft. horizontal tower spacing; 131 ft. footprint inverted V Note: When the "Documentation" tab is available, please look at the associated files for additional product information. The highest quality materials are used in construction of these antennas including stainless steel wire and fittings and UV resistant fiberglass rods. Quality materials and excellent design produces an antenna that will survive the rigors of the outdoors for many years. For an ultimate broadband dipole, remember these Bushcomm BBA-1KDE Kilowatt Multi-Wire Broadband Antennas from DX Engineering.

Not Yet Reviewed

$2,610.99