Availability
11 Results Found For "preamp"
Moonraker M-100 Professional 24-2300 MHz Preamplifier
Using GaAs FET technology, Moonraker M-100 Professional 24-2300 MHz Preamplifiers feature a variable gain control, -10 to +22 dB, and switched band pass filters to minimize interference. This preamp can be powered by an internal 9V battery or externally from 12 Vdc supply (not included). It comes complete with input and output BNC female connectors and BNC patch cable. Key Features and Specifications: Frequency coverage: 24-2300MHz Band Selections: Band A: 225-1500MHz Band B: 108-185MHz Band C: 24-2300MHz Gain: Variable, -10 TO +22dB Impedance: 50 ohms
( 15 )
$109.99
DX Engineering Portable Receive Preamplifier-Attenuator
DX Engineering Portable Receive Preamplifier-Attenuator DXE-NL-PRE-ATT-1 – A very handy device to use with your receiver; handheld, portable or base. This attractive, light-weight unit comes completely assembled and tested, and provides a nominal 30 dB gain across the frequency range from 100 kHz through 30 MHz. Powered by an internal 9 volt battery (not included), it features BNC connectors for RF Input and Output, easy to use slide switches and a 'power on' LED when the preamp is on. Attenuation is selected with switches for -10 dB or -20 dB and -30 dB with both. Plus, an AM Broadcast Band Rejection Filter can be switched in or out, as needed. This unit measures 3.25 x 7.00 x 1.00 in. (WHD) and weighs approx. 8.5 oz. with the user supplied 9V battery installed. This preamplifier has a Noise Figure (NF) of 4.5 dB. This Portable Preamplifier-Attenuator is a perfect companion device for use with the DXE-NOISELOOP WD8DSB Portable Receive Flag Antenna Kit, for RFI noise finding and for MW through SW receiving. NOTE: The DXE-NL-PRE-ATT-1 Portable Receive Preamplifier-Attenuator is a Receive Only device. Attempting to transmit RF into this unit will cause damage that is not covered by warranty.
( 14 )
$175.99
DX Engineering Clifton Laboratories Z10046 High-Gain Preamplifiers
DX Engineering Clifton Laboratories High-Gain Preamplifiers are adapted, assembled versions of the circuit project kits developed by Jack Smith, K8ZOA (SK). This is our version, the DXE-Z10046B-PM High-Output Preamplifier with 23dB gain, which is virtually identical to its predecessor in specs and performance. This versatile module preamp can plug directly into the DXE-NCC-2 and DXE-RTR-2 units. Also, you can easily create a separate high-performance in-line receive-only preamplifier with the DXE-Z10046B-PM module installed in our DXE-DMC-2 Dual Module Chassis. The legacy built by Jack Smith, K8ZOA (SK) with Clifton Laboratories lives on with select products by DX Engineering.
( 1 )
$109.99
I0JXX LNA Receive Preamplifiers
I0JXX LNA Receive Preamplifiers offer high gain amplification with very low internal noise for VHF and UHF amateur band optimized devices used world-wide by experimenters and contest enthusiasts. Excellent receive-only performance at low current is achieved by these compact 12VDC units, available in two connector configurations: SMA female input and output, or Type N male input and female output. LNA (low noise amplifiers) offer preamplification using ultra-low noise components as good or better than most receiver front ends, to preserve the capabilities of a low-noise antenna system. Typically, they do not have relays in the signal path that might introduce noise or loss. These devices can be used directly in most receive applications and may be used to build a sequencer-controlled Receive-Transmit relay system for two-way VHF or UHF communications. I0JXX LNA Receive Preamplifiers are built with high quality components including low-loss FR4 copper clad PCBs and environmentally safe tri-chrome high-conductivity passivated aluminum chassis. View the specific device specifications on each part detail page.
Not Yet Reviewed
$191.99
—
$223.99
QRO.cz RX Preamp Module Boxes
QRO.cz RX Preamp Module Boxes, featuring the 2N5109 transistor, are based on the proven W7IUV design and are ideal for use with receive-only antennas such as beverages, Double Half Delta Loops, flags, and other popular RX antenna designs. The Preamp Box offers up to 18dB of gain, with a built-in variable attenuator that allows you to easily adjust the gain to your desired level. A multi-turn potentiometer lets you fine-tune the transistor bias for optimal performance. The unit includes two relays that automatically switch to bypass mode when no power is supplied. Power can be provided either through a direct external DC connection or via a bias tee for power over coax.
Not Yet Reviewed
$123.99
DX Engineering Dual Module Chassis
The DX Engineering Dual Module Chassis is the connector and power interface box for all DX Engineering and Clifton Laboratories Plug-In Modules and Receive Filters. The DXE-DMC-2 is a versatile multi-purpose DX Engineering receive device box. It can be used for two passive plug-in modules or one powered module and one passive module. It is a great way to create a wide pass filter, or protect a receiver with a filter and a limiter, or add a preamplifier that has filtering or limiter protection. Here are the modules that can internally plug into the DX Engineering Dual Module Chassis: • DXE-Z10020-PM - Clifton Laboratories Z10020 AM Band Filter Module • DXE-Z10046B-PM - Clifton Laboratories Z10046 High-Gain Preamplifiers • DXE-RG5000HD-PM - Receiver Guard 5000HD Plug-in Module (passive) • DXE-IT-PM - 75 to 50 Ohm Impedance Transformer Plug-in Module (passive) • DXE-RPA-2-PM - Receive Preamplifier Plug-in Module (powered) • DXE-RXFL-1 - Receive Filter Adapter Board, for RXFL Filters (passive) One DXE-RXFL-1 Receive Filter Adapter Board is required to install any one of the RXFL filters listed below. They fit into the DXE-DMC-2, as well as the DXE-NCC-2, DXE-RTR-2 and DXE-RPA-2. The DXE-DMC-2 can accommodate one or two filters to create the filter type and input signal band pass frequency coverage and limitations that serves your needs. NOTE: The transition from the natural aluminum to the black powder coated chassis is occurring in early 2020. There is no internal electronic difference between them. Click on more details to see how you can build the receive accessory of your desires with the DX Engineering Dual Module Chassis.
( 2 )
$195.99
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit is based on the design by Don Kirk, WD8DSB. Don's article on this antenna is published in the March 2021 issue of QST Magazine (used by permission). The DXE-NOISELOOP is a kit of parts to build this receive-only portable directional HF loop antenna, which measures only 48 by 24 inches plus 36 inches of mast-handle. It may be used while walking or stationary with your portable HF receiver. Oriented vertically, this loop antenna features a cardioid pattern at the horizon with a deep null of up to 30 dB rejection. It is an excellent tool for locating noise sources from 1.8 through 30 MHz and for low-noise, general coverage reception from the AM broadcast band through 30 MHz. An optional Preamplifier-Attenuator Unit, DXE-NL-PRE-ATT-1, may be attached to the loop mast handle for enhanced operations. An IC-705, a portable SW or a handheld HF receiver are excellent choices for searching for local noise sources with the NOISELOOP, around the neighborhood and even around your own home. This Portable Flag Antenna Kit includes everything needed to make the antenna: fiberglass tubing for the frame and handle, mounting plate, separate PC boards for the bifilar wound transformer and load resistor, antenna wire, coaxial cable with male BNC and stainless steel hardware. Simple hand tools and a solder iron are required for assembly. Included instructions detail assembly. This kit will typically take between 1 and 2 hours to build. The WD8DSB Portable Flag Antenna design has become a real game changer in direction finding of RFI on MF and HF frequencies, and you will also find it an invaluable tool when hunting RFI due to the following key features. *Unidirectional (unlike a tuned loop) *Broadband (unlike a tuned loop, excellent for AM DXing, SWL and Amateur) *Portable (easy to walk with while directional noise finding or HF Fox Hunting) Traditionally Flag antennas are large and designed for stationary use, but the idea for this antenna was to design a Portable Flag. It was designed to be the largest possible (to maximize gain) that would fit inside a car and it's still small enough to maintain a cardioid pattern up through 30 MHz. The portable Flag has an approximate dimension of 2 feet tall by 4 feet long which you (or a helper) can easily walk with while tracking down a signal. Unlike a tuned loop, the Portable Flag is a broadband antenna with unidirectional properties, and it's designed for direction finding from 1.8 to 30 MHz as long as an appropriate preamp is used. It's even useful for direction finding down in the AM broadcast band. The rear of the antenna produces a sharp null when pointed at the signal of interest and the sharp null is often used for direction finding versus using the broad peak which occurs when the front of the antenna is pointed at the signal of interest. Learn more about how to build this antenna kit by clicking on More Detail and the Documentation link for the Instruction Manual. Order your DX Engineering NOISELOOP Portable Receive Flag Antenna Kit here.
( 15 )
$159.99
DX Engineering Clifton Laboratories Z10020 AM Band Filter Module
DX Engineering Clifton Laboratories Z10020 AM Band Filter Module drastically reduces RF signals in the 530 to 1700 kHz MW range while passing frequencies below and above this range with minimal attenuation. A large section of the AM Broadcast Band (BCB) is attenuated by nearly 70db with a maximum of 75dB. Response rolls off quickly above 490 kHz and below 1.8 MHz. Detailed plots demonstrate the excellent performance of this AM band receiving rejection filter. The DXE-Z10020-PM RX AM Reject Filter plug-in module is our version of the 7th Order Chebyshev design built to deliver the performance of the original Clifton Labs AM Broadcast Band (BCB) filter. It provides excellent Broadcast Interference (BCI) filtering performance for Amateur low band and commercial SW receive applications, with less than 2dB insertion loss across the 160 meter band. The DXE-Z10020-PM module can be installed in the DXE-DMC-2 Dual Module Chassis to create an inline high-performance receive-only AM Band Reject Filter. Or, install one of these versatile AM filter modules inside of the DXE-RPA-2 Receive Preamplifier or the DXE-RTR-2 Receive Antenna Interface. Two AM BCB Reject Filter modules will cover the two channels of the DXE-NCC-2 Receive Antenna Phasing Unit. The legacy built by Jack Smith, K8ZOA (SK), at Clifton Laboratories lives on with select products by DX Engineering.
( 2 )
$163.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$103.99
Antennas-Amplifiers 6505 70cm Low Loss Receive Band Pass Filters
Antennas-Amplifiers 6505 70cm Low Loss Receive Band Pass Filters are engineered for optimal performance in weak signal, terrestrial, and EME applications. Designed for direct connection to a coaxial relay, the 6505 filter minimizes insertion loss in the receive path, ensuring that wideband preamplifiers experience virtually no degradation to their noise performance. By sharply rejecting strong out of band signals, the 6505 provides stable operation in environments with strong adjacent band or high power local signals. The filter is housed in a sturdy 0.8 mm brass enclosure, providing excellent mechanical stability, long term durability, and consistent electrical characteristics over time.
Not Yet Reviewed
$175.99
Antennas-Amplifiers 5910 Low Loss 6-meter Receive Band Pass Filters
Antennas Amplifiers 5910 Low Loss 6 meter Receive Band Pass Filters deliver exceptional performance on the legendary 6m "Magic Band," offering high selectivity, a high Q design, and impressively low insertion loss. Engineered to confine received signals strictly within the 50–51 MHz amateur band, these filters dramatically reduce out of band noise, lowering the noise floor and enhancing weak signal reception. When placed ahead of SDRs or wideband receivers, they effectively remove unwanted HF, 4m, FM broadcast, 2m, and 70cm signals, leaving us with a clean and focused 6m passband. Just as important, these filters will not disturb the noise performance of preamplifiers—an essential advantage for contesting, DXing, and EME—while ensuring smooth, stable operation even in the presence of strong nearby signals. With an insertion loss of just 0.1 dB, they safeguard receiving performance without compromise, a level of efficiency achieved through careful design and precise tuning. In multi operator contest stations or portable field setups, they provide essential isolation by minimizing images and harmonic interference, ensuring crisp monoband operation even in crowded RF environments. These 6 meter band pass filters are the ideal choice for operators seeking cleaner signals, improved performance, and reliable protection for sensitive front end equipment.
( 1 )
$180.99