Selected Filters


Availability


2 Results Found For "Receive Array"

Part Groups

Results 1 - 2 of 2

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.

Not Yet Reviewed

$1,299.99

Manufacturer Rebate

ICOM IC-7300 HF Plus 50 MHz Transceivers

ICOM IC-7300 HF Plus 50 MHz Transceivers employ a new-technology real-time touch-screen spectrum scope that leads its class in resolution, sweep speed and dynamic range. While listening to received audio, you can check the real-time spectrum scope and quickly move to another signal. When you first touch the scope screen around the intended signal, the touched part is magnified. A second touch of the scope screen changes the operating frequency and allows you to accurately tune to the desired signal. The combination of the waterfall function and the real-time spectrum scope assists in maximum receive performance of IC-7300 radios and increases QSO opportunities without missing weak signals. The waterfall function shows a change of signal strength over a period of time and allows you to find weak signals that may not be apparent on the real-time spectrum scope. The audio scope function can be used to observe various AF characteristics such as microphone compressor level, filter width, notch filter width and keying waveform in the CW mode. Either transmit or receive audio may be displayed on the FFT scope, with the waterfall function and the oscilloscope. The large 4.3 in. color TFT touch LCD offers intuitive operation. Using the software keypad of the touch screen, you can easily set various functions and edit memory contents. IC-7300 transceivers employ an RF direct-sampling system. RF signals are directly converted to digital data and processed in the FPGA (Field-Programmable Gate Array), making it possible to simplify the circuit construction. This system is a leading-edge technology; creating a new era in amateur radio. The new "IP-plus" function improves 3rd order intercept point (IP3) performance. When a weak signal is received adjacent to strong interference, the AD converter is optimized against signal distortion. IC-7300 transceivers' RMDR is improved to about 97dB (typical value) and Phase Noise characteristics are improved about 15dB (at 1 kHz frequency separation) compared to the IC-7200. The superior Phase Noise characteristics reduce noise components in both receive and transmit signals. IC-7300's have 15 discrete RF band-pass filters. The RF signal is passed through only one of the band-pass filters, while any out of range signals are rejected. High Q factor coils are used to minimize the loss in the RF band-pass filters. The built-in antenna tuner memorizes its settings based on your transmit frequency, so that it can rapidly tune when you change operating bands. The Enforced Tuning function allows a wide range of temporary antennas to be tuned. NOTE: Do not use the Enforced Tuning function except in case of an emergency. Transmitter output power may be automatically reduced. IC-7300 transceivers can store various contents into an SD card, such as received and transmitted audio, voice memories, RTTY/CW memories, RTTY decode logs and captured screen images. Updated personal and firmware data can also be stored to the SD card for easy setting. To offer superior sound quality, a new speaker unit has been incorporated and is designed into the aluminum die-cast chassis; not just squeezed in as a necessity. Other IC-7300 features include: * HM-219 hand microphone supplied * Large, effective cooling fan system * Multi-function meter * 101 memory channels (99 regular, plus 2 scan edges) * Optional RS-BA1 IP remote control software (the spectrum scope with the waterfall can be observed) * CW functions: Full break-in, CW reverse, CW auto tuning Note: For additional information, look at the files under the "Documentation" tab. The innovative features included in ICOM's IC-7300 offer tremendous advantages and represent a paradigm shift for its modest price point. ICOM says of its 7300 that "The Real HF Fun Starts Here." Order one of their ICOM IC-7300 HF Plus 50 MHz Transceivers and discover the fun to be had with leading-edge technology transceivers from DX Engineering!

4.93 out of 5 stars ( 553 )

$1,039.95

  • 1
  • Page 1 of 1