Availability
22 Results Found For "in-line"
DX Engineering Guy Line Guards
DX Engineering Guy Line Guards are used on towers to prevent damage to coaxial cable rotator loops from rubbing directly on metal guy lines or dead ends. Guy Line Guards are a high visibility yellow poly plastic tubing material that is split lengthwise for easy installation on existing guys. Each Guard features a single hole for the included zip-tie to secure it in place. For coax protection they are mounted at the top of the guy lines and, since they are yellow in color, Guy Line Guards may also be mounted at the bottom of the guy lines to warn people that the guy line is present. Guy Line Guards are approximately 45 inches (1.14 m) in length and come in a set of three.
( 4 )
$35.99
DX Engineering Porcelain Guy Line Strain Insulators
DX Engineering Porcelain Guy Line Strain Insulators provide the strength, insulation and isolation you need for guyed tower systems. These porcelain insulators accept large guy lines, dead ends or bent-pin shackles and are suitable for all guyed towers where breaking strength for each insulator is not exceeded. DXE-502 insulators are rated at 10,000 lbs. breaking strength. The more-massive DXE-504 insulators take that number to 12,000 lbs. of force. Stranded steel 1/4 EHS cable has a breaking strength of about 6,500 lbs. DXE-504 insulators are nearly twice that value! DX Engineering Porcelain Guy Line Strain Insulators provide flashover insulation of at least 12kV… when wet! These insulators will also let you section your steel guy lines to avoid resonant-length interactions or pattern-modifying interference with your radiated signals. They are perfect for use with synthetic guy lines too. Use them to provide steel lower guy tails to avoid vandalism or damage to synthetics due to large animals. Do towers right! Choose a good design and then buy DX Engineering Porcelain Guy Line Strain Insulators to erect and maintain towers the right way.
( 13 )
$21.99
—
$29.99
DX Engineering RF Attenuators
DX Engineering RF Attenuators are used inline with receiving equipment for testing purposes. An inline attenuator will limit the RF input to preamplifier to prevent overload or be used to pad the output of a high gain preamp to an appropriate level. Adding an inline attenuator to a receiver input allows determination of accuracy of s-meter readings on transceivers with a constant RF input signal source. Sometimes, the level of low power RF equipment needs to be reduced for measurement or to obtain the proper input level to an amplification device, such as with QRP equipment. Specifications of impedance, attenuation, power handling and connectors appear on the part number description. Order inline RF Attenuators for your test bench or shack from DX Engineering.
( 5 )
$45.99
DX Engineering Ladder Line Surge Protector Replacement Parts Kit
DX Engineering Ladder Line Surge Protector Replacement Parts Kit, DXE-LLSP-RP, is a kit to use if your DXE-LLSP should ever be damaged. In some locations with lots of lightning, or wind driven static charge buildup, a spare protector or this replacement parts kit is a smart investment. In a few locations you may never need one of these kits. But, here are the parts to rebuild the DXE-LLSP should the need ever arise. These are exactly the same components used in the DXE-LLSP. Along with a replacement PC board, the capacitors, resistors and gas discharge tubes provided are larger than those used in coaxial units. These components are rated to handle 5 kW, so the DXE-LLSP easily handles well over legal limit RF power at the high standing wave ratios expected on balanced line. Plus, the Ladder Line Surge Protector bleeds off the static charge that is collected on your antenna from wind driven sand, rain and snow! To refurbish your Ladder Line Surge Protector, order this kit of parts: DXE-LLSP-RP, DX Engineering Ladder Line Surge Protector Replacement Parts.
( 1 )
$29.99
DX Engineering Rotator Control Line Connectors
Available here, individually, are the "remarkable and elegant" 4-pin interlocking weather-sealed rotator control line connectors that have metal bodies to provide RF shielding, as supplied with the DXE-RT4500HD. These DX Engineering Rotator Control Line Connectors are top-of-the-line cable-mount solder connectors that are intended to be used outdoors, for a lifetime of reliable control line termination. Their positive latching, moisture-sealing, quick disconnect features make them ideal to build an extension, pigtail or test cable for your DXE-RT4500HD or controller. They are a perfect match for DX Engineering DXE-CW1812OR Heavy-Duty Spec Rotator Cable, with 5 conductors: 2 x 12 AWG and 2 x 18 AWG plus 1 x 18 AWG shield. Each gender are used to build your own rotator cable assembly extension. Just as with standard power extension cords, use female for the power source end and male for the mating end of the extension, so there is never an exposed pin with voltage present. In this case, use the DXE-LP-20-F female connector on any cable, controller pigtail or the rotator end of an extension that can have a voltage present. Use the DXE-LP-20-M male connector on the controller end of the mating extension cable. DXE-LP-20-F 4-pin female to make a controller pigtail or for the end of a cable assembly that mates with the male rotator pigtail. This connector is supplied with DXE-RT4500HD Heavy Duty Rotators DXE-LP-20-M 4-pin male as supplied on the permanently mounted DXE-RT4500HD Heavy Duty Rotator. Used for the controller end of an extension cable to mate with a controller pigtail. These are the best connectors, to make the best weather-sealed 4-conductor cable assembly, for the best rotator on the market, all from DX Engineering.
Not Yet Reviewed
$20.99
DX Engineering Radial Wire Metal Anchor Pins
DX Engineering radial wire metal anchor pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your radials during lawn maintenance. They are manufactured from 11-gauge steel and are 6 in. long to help keep the cables buried properly.
( 39 )
$22.99
DX Engineering Super Duty Saddle Clamps
DX Engineering set new standards over ten years ago with the introduction of the industry's best clamps for mounting antennas and element tubing. DX Engineering Super Duty Saddle Clamps are available to fit 2.00, 2.50 or 3.00 inch OD tubing with ultimate gripping power. Commercial and industrial engineers and installation technicians all over the world have discovered a diverse range of applications for DX Engineering Super Duty Saddle Clamps. Super Duty Saddle Clamps are designed to be used where maximum torque handling is required on aluminum, steel or stainless steel tubing. Conceived for use by builders of large and heavy Yagi antennas and Log Periodic arrays, these clamps are made in sizes that securely fit the outside diameter of tubing for mounting to a flat plate or surface. Their wider gripping surface equals superior clamping power! Perfect for antenna construction and mounting, or wherever standard U-bolt saddle clamps and other torque-control products have proven inadequate, Super Duty Saddle Clamps provide maximum grip on booms, masts and element tubing. Unlike stamped or machined-type clamps, Super Duty clamps are cast from a rugged aluminum that grips tubing with a special textured surface and are sized for an incredibly secure fit that resists torque, wind and weather. Super Duty Saddle Clamps include two cast aluminum saddles (two halves) and a stainless steel reinforcement plate for high strength and superior corrosion resistance. Due to the wide diversity of clamping applications where Super Duty clamps are beneficial, mounting hardware is NOT included. However, a complete line of Armor-Coated and Stainless Steel Hex Bolt Hardware Sets are available for top performance in most mounting applications. Click "More Detail" to see additional information. Super Duty clamp mounting applications on a 1/4 in. plate require a bolt set, as indicated in the chart linked in the Documentation tab on the part detail page. Our tradition of innovation continues with the addition of narrower solid saddle clamps, our DX Engineering Heavy Duty Saddle Clamps, available to fit tubing with Outside Diameter (OD) inch-sizes of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Plan your next project with the best clamps available... period. DX Engineering Super Duty Saddle Clamps are ready to provide superior performance for your antenna, mast or other tubing mounting application.
( 7 )
$47.99
DX Engineering Heavy-Duty Saddle Clamps
Our tradition of continuous innovation was evident with the introduction of the DX Engineering Heavy-Duty Saddle Clamp line. DX Engineering set new standards over a decade ago with the introduction of the industry's best clamps for mounting antennas and element tubing. Featuring superior gripping power, our new Heavy-Duty Saddle Clamps are available in six different sizes, to fit tubing with Outside Diameter (OD) inch sizes of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00. Commercial and industrial engineers and installation technicians all over the world have discovered a diverse range of applications for DX Engineering Heavy Duty Saddle Clamps. DX Engineering Heavy Duty Saddle Clamps are designed to be used where maximum torque handling is required on aluminum, steel or stainless steel tubing. Conceived of by builders of large and heavy Yagi antennas and Log Periodic arrays, these clamps are made in sizes that securely fit the outside diameter of tubing for mounting to a flat plate or surface. Their wide gripping surface equals superior clamping power! Perfect for antenna construction and mounting, or wherever standard U-bolt saddle clamps and other torque-control products have proven inadequate, our Heavy Duty Saddle Clamps provide excellent grip on booms, masts and element tubing. Unlike stamped or machined-type clamps, Heavy Duty Saddle Clamps are cast from a rugged aluminum alloy that grips tubing with a special textured surface and are sized for an incredibly secure fit that resists torque, wind and weather. Heavy Duty Saddle Clamps include two cast aluminum saddles (two halves) and a stainless steel reinforcement plate for high strength and superior corrosion resistance. Due to the wide diversity of clamping applications where Heavy Duty clamps are beneficial, mounting hardware is NOT included. However, a complete line of Armor-Coated and Stainless Steel Hex Bolt Hardware Sets are available for top performance in most mounting applications. Typical Heavy Duty clamp mounting applications on a 1/4 in. plate require a minimum length bolt set, as indicated in the chart, linked in "More Detail…," and displayed in the "Required Parts" tab. For larger tubing attachment applications with ultimate gripping strength, DX Engineering Super Duty Saddle clamps are also available for 2.0, 2.5 and 3.0 in. O.D. sizes. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Plan your next project with the best clamps available... period. DX Engineering Heavy Duty Saddle Clamps are ready to provide superior performance for your antenna, mast or other tubing mounting application.
( 11 )
$21.99
—
$23.99
DX Engineering Grounding Clamps
DX Engineering Grounding Clamps are used to connect wire grounding conductors of AWG 2 through 10 to a ground rod, tower leg or grounded pipe. These clamps are manufactured from cast bronze, a highly conductive copper alloy, and include high quality 1/4-20 stainless steel screws for maximum longevity and durability. These clamps also accept the stud from our IS-RCT control line protectors, to provide the proper protection of rotator control lines at the base of a grounded tower. Please note that pipe is measured by ID, not OD. For example, 1-1/4 pipe is much larger than 1-1/3 in. OD. DX Engineering Grounding Clamps are available in two sizes, to fit your grounding project. These are great general purpose grounding clamps to have on hand for future projects, so add a few to your order today!
( 8 )
$45.99
DX Engineering Portable VHF/UHF Antenna Mounts
Designed for rapid deployment in portable operations, the DXE-MOBILEPORT-U is the ideal solution for mounting VHF/UHF or GMRS vertical antennas in the field. Whether you're camping, participating in Field Day, supporting EmComm activities, or setting up a temporary station, this mounting plate simplifies antenna setup in challenging environments. The center hole is sized to fit over collapsible masts like the DXE Nomad fiberglass mast, providing a stable and secure base. Four outer holes serve dual purposes: they can anchor guy lines for mast stabilization and support soldered wires to create a ground plane—if your antenna requires one. However, for best performance and simplicity, a no-ground-plane-required antenna is recommended. Compact, lightweight, and versatile, the DX Engineering MOBILEPORT-U Portable VHF/UHF Antenna Mounts are a must-have for any portable antenna deployment kit. Important Note: This mounting plate is intended for use with fiberglass masts only. Carbon fiber masts are not recommended, as they may interfere with RF signals and cause SWR issues due to their conductive properties.
Not Yet Reviewed
$29.99
DX Engineering Electronic Protection Components
DX Engineering Electronic Protection Components may be used in a variety of electronics and radio applications. These are wire lead components that can be used on circuit boards or in multi-purpose connection devices. Choose from the components listed for detailed specifications: DXE-MOV-82VDC-10 Metal Oxide Varistor, Surge Protector, max. 82VDC/50VAC Pack of 10 DXE-GDT-4KV-5 Gas Discharge Tube, Surge Arrestor, 4kV, Pack of 5 DXE-TVS-1500-10 ESD Suppressor, TVS Diode, Bidirectional, 17VDC max., Pack of 10 DXE-CAP-PT1UF-10 Capacitor, Ceramic, 0.1uf, 1kV DC, RF Bypass, Pack of 10 ---------------------------------------------------------------------------------------------------------------------------------- This series of protection components are well suited for the DXE-CLTB Control Line Terminal Board that provides a flexible and simplified approach to control line surge protection. The DXE-CLTB is a small, 3 inch square printed circuit board (PCB) with four ten-wire compression screw terminal blocks that handle from 14 to 26 AWG conductors and up to 10A. The two outer terminal blocks are for input and output of the control wires and the two 45 degree angled ten-wire compression screw terminal blocks are for connecting electronic surge protection components. This provides for the choice of components to install between the control line and ground to provide shunt protection. Metal Oxide Varistor (MOV), Gas Discharge Tube (GDT), EMP Suppressor TVS Diodes, RF Bypass Capacitors and other wire lead components are easily connected between the control lines and ground. For effective protection wherever shunt devices are used, a low impedance ground is critical. The DXE-CLTB Control Line Terminal Board has four corner grounding screw holes for mounting on metal standoffs to a metal grounding panel inside an enclosure. DXE-CLTB-M Control Line Terminal Board includes a 10-pack of MOVs.
( 1 )
$20.99
DX Engineering F6 Cable Tool Cases
DX Engineering F6 Cable Prep Tool Cases keep your 75-ohm F-6 coaxial cable prep tools in one secure case. These rugged, lockable cases are lined with a precut foam insert to provide a home for each tool. Keep your tools together, protected, and out of sight with DX Engineering F6 Cable Prep Tool Cases.
Not Yet Reviewed
$31.99
DX Engineering Utility Tool Cases
DX Engineering Utility Tool Cases offer many uses. These rugged molded plastic cases are lined with low-density convoluted foam, which conforms to the shape of the items stored inside. These cases have two snap latches and are designed to be secured with your padlock through the handle area. Keep your tools and other handheld valuables out of sight, secure, and protected against impacts with DX Engineering Utility Tool Cases.
( 4 )
$20.99
DX Engineering Direct Coax Feed Add-On Kits
DX Engineering Direct Coax Feed Add-On Kits are designed for the Hustler BTV Series of antennas. They allow for a direct connection with a coaxial cable PL-259 (UHF male) connector. Manufactured from heavy-duty stainless steel, these add-on kits allow for a convenient connection from your coaxial cable feed line directly to the base of the Hustler BTV series vertical antennas by adding a mounted SO-239 (UHF female). They may be positioned in any one of three different directions to accommodate a straight-in or sideways connection from your feed line. If you are looking for a professional and reliable installation, then order a low power or high power (low loss) coaxial jumper cable for connecting your radial plate with a bulkhead connector. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering Direct Coax Feed Add-On Kits include a laser-cut stainless steel bracket, high quality SO-239 with PTFE insulation, and stainless steel hardware. Order one for your BTV vertical!
( 79 )
$42.99
DX Engineering TWIG Broadcast Interference Filter
Improve the performance of your QRP POTA or SOTA station with the DX Engineering DXE TWIG BCFIL Broadcast Interference (BCI) Filter. Engineered specifically for low power amateur radio applications, this compact module effectively attenuates strong AM broadcast band signals below the 80 meter amateur band. By suppressing these out of band signals, the filter helps lower your receiver's noise floor, resulting in cleaner, more reliable reception of weak amateur radio signals. The DXE TWIG BCFIL is equipped with BNC female connectors for quick, in line installation in the field. Ideal for portable, field, and low power fixed station use, it provides an effortless way to reduce unwanted broadcast interference without adding complexity to your station setup. Features: • Blocks strong AM broadcast band and 1.8 MHz signals below the 80 meter amateur band • Improves receiver noise floor and enhances reception of desired signals • Designed for low power transceivers • Compact in line module with BNC female connectors for easy installation • Ideal for portable POTA and SOTA, mobile, and fixed low power stations Power Rating: For QRP use only — maximum 20 watts PEP. Not suitable for high power transceivers.
Not Yet Reviewed
$49.99
DX Engineering Transceiver Amplifier Keying Cables
DX Engineering Transceiver Amplifier Keying Cables connect the "ground on transmit" or contact closure provided by the radio that is required to make an HF amplifier switch from "receive mode" to "transmit and amplify mode" when using PTT (push-to-talk), VOX or break-in CW keying. DX Engineering Transceiver Amplifier Keying Cables are made for specific transceiver models that have special DIN or mini-DIN connector accessory ports which provide the transceiver's only connections for linear amplifier keying. One type of amplifier keying cable has one RCA phono plug for the amplifier relay jack, which is all that is needed. When the transceiver PTT (push-to-talk) is keyed, the RCA plug center pin is connected to the shield (and chassis ground in most cases) to key the amp relay or its solid state keying circuit. Instead of a direct connection to the amp relay, the RCA plug may be connected to the keying input of an accessory device (DXE-KEYLINE-3, DXE-RTR-2 or DXE-NCC-2), amplifier keying interface (DXE-SV-KR or legacy Ameritron ARB-704 or KD9SV Products SV-KR) or other amp keying line interrupt device, such as a meter or an array controller. Each has a keying input and a keying output for the amplifier relay or another accessory. Another type of amplifier keying cable has two RCA phono plugs, one RED plug for the amplifier relay jack and one WHITE plug for ALC (Automatic Level Control) voltage from the amplifier. The legacy ALC connection does not need to be used with present era solid state transceivers and most modern amplifiers. ALC was required for use on transmitters with tube finals. Some modern amplifiers do not have an ALC output connector. If the amplifier does not have ALC it is okay to leave the WHITE plug disconnected. Order your DX Engineering Transceiver Amplifier Keying Cables to connect to your transceiver accessory port for keying amplifiers, sequencers, receive-transmit interfaces, buffer relays, and other accessories. NOTE: To enable the function of this keying cable, some late model Kenwood transceivers require menu activation of the amplifier keying circuit.
( 51 )
$36.99
—
$41.99
DX Engineering EZ-BUILD® UWA Center-T and End Insulator Kits
DX Engineering EZ-BUILD® UWA Center-T and End Insulator Kits are designed for building wire antennas for high-power operations. This model will mount to any DX Engineering Balun for a balanced and isolated wire antenna, or this insulator kit may be used directly with DX Engineering 300 Ohm Ladder Line for a non-resonant multi-band dipole. All EZ-BUILD® kits include our lightweight, high strength, UV-protected center-T and end insulators. They feature an exclusive serpentine wire grip for insulated DX Engineering antenna wire and our high strength, high power 300 ohm ladder (window) line. Threading the wire or window line through the center and end insulator openings in a serpentine manner creates a grip that is so strong, the wire ends do not need to be looped, wrapped, or soldered. EZ-BUILD® kits allow for fast and easy field adjustments! The DX Engineering EZ-BUILD® Center-T includes a centered top 3/8 in. hole for the attachment of an antenna support rope, and the End Insulators accept up to 5/16 in. antenna support rope. Our EZ-BUILD® kits simplify the construction of your wire antenna, with wire crimp terminals and stainless steel hardware. For a wire antenna, built with a DX Engineering Balun at the feed-point, the coax feedline may be secured with the optional DX Engineering Coax Strain Relief which features an aluminum bracket, neoprene-cushioned P-clamps, and stainless steel hardware. This method supports the feedline without subjecting the balun connector to the strain of the coaxial cable's weight or movement. DX Engineering EZ-BUILD® UWA Center-T and End Insulator Kits let you create any type of wire antennas, including single-band, multi-band, multi-frequency, folded dipole, doublet and inverted-V, off-center fed, Windom, Zepp, long wires, rhombic, V-beam, or loop antennas. EZ-BUILD® UWA Center-T may be used as a strain relief for our 300-ohm ladder line at the ground end or house end of the run, or as the strain relief on the feed end of a vertical wire or long wire antenna. Since soldering is not necessary when building an antenna with this kit, it is perfect for Field Day use, portable operations, or even for the weekend experimenter. However, it is certainly the best choice for your permanent wire antenna system. This UWA-KIT is for building a wire antenna with any DX Engineering Balun or 300 Ohm Ladder Line. Use the EZ-BUILD® UWA213-KIT for the construction of an RG-213 or RG-8U coax fed wire antenna without a balun, that will be operated at high power and high duty cycle modes of operation, such as AM, RTTY, or FM. The UWA8X-KIT will handle low and medium power levels and tolerate low SWR levels. DX Engineering EZ-BUILD® UWA Center-T and End Insulator Kits include: -- One center-T insulator featuring an exclusive no-loop, no-solder wire, multiple wire, or 300 ohm ladder line serpentine grip design, which allow for the rapid field adjustment of wire lengths; the center-T includes a centered top hole for attaching support ropes -- Two end insulators featuring the no-loop, no-solder, serpentine grip design -- Two stainless steel wire connection bolts, nuts, and washers. -- Six crimp ring terminals for antenna and ladder line wire connections -- Additional stainless steel hardware for mounting DX Engineering baluns DX Engineering baluns, antenna wire, 300 ohm ladder line, and support rope are sold separately. Only your imagination is the limit to the practical applications for which this useful insulator system may be used. It is made from a very strong UV resistant poly-resin plastic that can handle the weight of huge wire antennas, and a DX Engineering balun as well as the attached coaxial cables. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. So, keeping an inexpensive EZ-BUILD® DXE-UWA-KIT on hand for your next wire antenna project is a great idea!
( 25 )
$30.49
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$21.99
—
$44.99
YCCC Receive Feedline Choke Kits
Closeout- Other YCCC array components are no longer available YCCC Receive Feedline Choke Kits prevent common-mode noise or unwanted signal intrusion on the feed lines of YCCC Receive Vertical Array Kits. These choke kits are the same as provided in the array kit packages and may be used as replacements or in other applications. Component-level assembly of these kits is required. A choke enclosure is user supplied. Their function is to provide isolation between the input and output coaxial shield connections, while passing desired receive or control signals. Their isolation impedance blocks common-mode noise or unwanted signals. YCCC Receive Feedline Choke Kits are supplied with standard "F" female connectors to prevent connection to transmitting equipment. All inquiries and technical support for the discontinued YCCC kits and kit packages is handled by e-mail only, typically within two to three business days: yccctechsupport@verizon.net
Not Yet Reviewed
$22.00
DX Engineering MB-2 Passive Splitters
DX Engineering MB-2 Passive Splitters cover from 500 kHz to 2.4 GHz. These splitters allow you to feed any combination of AM/FM/TV and Satellite Radio to two separate locations from multiple antennas that employ a signal combiner. Once the combined signals pass through one of these splitters and reach their individual locations they may be split-apart into their separate bands. Insertion loss from these splitters is only 3.5-dB. One of the output ports is DC power passing to the input to allow the use of inline amplifiers or other equipment requiring coaxial-line power. When you need to split multiple-band signals to two locations from a single coaxial cable, order one of these DX Engineering MB-2 Passive Splitters!
Not Yet Reviewed
$20.99
DX Engineering Receive Filter Plug-In Modules
DX Engineering Receive Filter Plug-In Modules provide frequency-specific receiving system enhancements, which fit into special DX Engineering devices listed below. These advanced plug-in filter modules are available separately to allow any user to create a specific or customized filter with low-pass, band-pass and high-pass frequency ranges. Filter cut-off and center frequencies correspond to the major Amateur bands, 160, 80, 40, 20, 15 and 10 meters, with filter module insertion loss of only about 1dB. By reducing or excluding frequency-specific interfering noise and signals, the noise floor can be lowered for the desired passband for dramatically improved reception DX Engineering Receive Filter Plug-In Modules may be installed in these devices: DXE-DMC-2 Dual Module Chassis accepts one or two filter modules to create a stand-alone passive inline filter unit of any configuration. One high pass and one low pas can be combined to create a multi-band bandpass filter of any HF range. DXE-RPA-2-PM Modular Receive Preamplifier accepts one Receive Filter Plug-In Module to customize the preamplifier passband. DXE-NCC-2 Receive Phasing Controller can accept one or two Receive Filter Plug-In Modules, one into each, Channel A and Channel B. The DX Engineering NCC-2 is highly regarded by many owners and engineers to be the best receive phasing and noise canceling unit available and is used extensively by enthusiasts in Amateur Radio DXing, Contesting, AM DXing, and Short-Wave Listening (SWL), and is also used in commercial AM and HF broadcast applications. DX Engineering Receive Filter Plug-In Modules add an extra dimension of functionality to the NCC-2, for advanced directional noise and signal nulling performance, enhanced with a specific frequency range operations. By default, NCC-2 internal option slots have bypass boards to pass all signals. Receive Filters placed into these slots dedicate the unit to filtered operation. Typically, one pair of band-pass or high-pass or low-pass filters, depending on desired filtering, is installed in the NCC-2 to suit the specific signal rejection needs of the discerning operator. As an example, an 80 meter DX enthusiast may elect to install two 80 meter band pass Receive Filter Plug-In Modules, part number DXE-R-BP80-PM, into their NCC-2 Channel A and Channel B middle slots. This dedicates their NCC-2 to 80 meter-only operations. This dramatically reduces noise and signals from outside the 80 meter band, very effectively excluding interference from nearby AM Broadcast, 160 and 40 meter stations. A much lower noise floor across 80 meters can help achieve reception of weak 80 meter DX signals. An additional pair of filters can be swapped out for a different band when desired. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. All Receive Filter Plug-In Modules displayed here are also conveniently listed on a single page linked in Documentation.
Not Yet Reviewed
$49.99
DX Engineering Weatherproofing Kits
DX Engineering Weatherproofing Kits weatherize your outdoor connections and prevent moisture entry and corrosion with vapor wrap and high quality electrical tape. When your non-weather resistant equipment needs to be mounted outdoors, these weatherproofing kits provide needed protection. Use these kits to protect lightning protectors, coaxial connections, antenna joints, steel hardware, junction boxes and just about anything you can wrap with tape by using these kits. The non-conductive malleable vapor wrap sealant is water-impermeable and withstands temperatures from minus 65 degrees F to plus 180 degrees F without cracking. Choose from Standard, Upgraded or Ultimate kits with different grades of vinyl tape. The WK-PRO Kit has more vapor wrap material and five rolls of tape for large projects. See each kit's detailed description. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Reliable waterproofing is important to protect equipment and cable connections from damage caused by moisture penetration. Protect your equipment, handle extreme temperatures, and remain unaffected by water and UV sun rays with DX Engineering Weatherproofing Kits.
( 19 )
$20.99
—
$23.99