Availability
Parts and Accessories
DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coax Cable Assemblies
Our patented* revolutionary new PL-259 connector and our premium flexible DXE-8X coaxial cable were designed to make the new DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8X cable assemblies available for HF applications. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket, good for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. DX Engineering RG-8X PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These new, ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849
( 538 )
$36.99
—
$49.99
DX Engineering Ferrite
DX Engineering Ferrites are partially magnetic metal and ceramic mixes available in a variety of forms, including toroid core, bead type and plastic-covered split-bead ferrite called snap-beads. They are used in a myriad of RF suppression applications to mitigate RFI (radio frequency interference) as well as to reduce pulse and other types of RF noise interference. Special ferrites are used for experimentation and electronic circuit building and for making transformers, RF chokes and antenna baluns. The variations of magnetic and non-magnetic metals and non-metal ceramics used to make ferrites are called "Mixes" and each has different radio frequency properties or ranges. Therefore, different mix number ferrites are typically used for different applications within those ranges, determined by decades of experiments by engineers and applications by hams. Each Mix has been assigned a color code to help identify the ferrite, so numerical labeling is not used on the metal. Color coded ferrite can be identified long after the numbered package is discarded or has disintegrated with time. How do they work? Simply use snap-on beads on a cable or wire. An even more effective choke takes a few to several turns of a wire or cable through and around a ferrite snap-on bead or toroid core. This mitigates RFI to, or from, the connected RF noise producing or noise affected electronic device. The results can be very surprising. Solving noise and RFI can be frustrating. Due to the nature of RF and noise interference suppression; the techniques of appropriate use of ferrites can take a bit of trial and error, but are often the best solution for a difficult problem. Use DX Engineering Ferrite for an incredible range of electronic circuits, noise abatement and RF suppression projects. The details of DX Engineering Ferrite mixes and types appear in each product description. Sizes and applications are discussed in "More Details" and in the literature available at the "Documentation" tab of each of these products.
( 194 )
$27.99
—
$49.99
DX Engineering Next Generation Crimp/Solder 8X PL-259 Connectors
DX Engineering proudly announces our new, ultra-high quality, PL-259 connector that is so different from previous designs that we have a Patent**! DX Engineering Next Generation Crimp/Solder 8X UHF Male Connectors are now available to build your custom coaxial cable assemblies. Engineering studies have confirmed that the absolute best RF connections for double-shielded cables are made by crimping the shield, not soldering. However, most PL-259 crimped center pins aren't long enough and some don't even have enough crimped contact area, which affects reliability. DX Engineering has solved those issues with these custom-designed connectors that we introduced on new DX Engineering 8XDX Series Coaxial Cable Assemblies. These PL-259s have soldered center pins that are full length and full diameter, so they connect properly, even with worn SO-239s. DX Engineering Next Generation PL-259CS8X series connectors achieve exceptional RF performance with these features: * Fits all standard RG-8X size cables including DXE-8X, LMR-240 as well as RG-59, RG-62 and many others, including Belden 9258, 8241, 1505 and 7808 series * All silver-plated brass shell and body * Silver-plated center pin securely mounted in PTFE dielectric * Center pin scalloped-tip allows generous solder flow * Crimped shield connection provides maximum reliability for all cables * Deep, double-knurled threaded shells for secure finger tightening * Available in packages of 6, 12 or 24 connectors NOTE: DX Engineering offers reasonably priced, professional grade cable prep and connector crimping tools for an entire range of cables and connectors. Click "More Details" and the "Suggested Parts" tab to see available related products. Now you don't have to use the same old PL-259s. These advanced-technology PL-259 connectors let you build the highest quality coaxial cable assemblies. We designed them to be strong and lightweight and they represent a landmark improvement over decades-old, unchanged connector designs. This time, new IS better! Order DX Engineering Next Generation Crimp/Solder 8X UHF Male Connectors today and take advantage of DX Engineering innovations in RF connectivity! **U.S. Patent D745849
( 157 )
$33.99
DX Engineering Next Generation Crimp/Solder 8U PL-259 Connectors
DX Engineering proudly announces our new, ultra-high quality, PL-259 connector that is so different from previous designs that we have a Patent**! DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors are now available to build your custom coaxial cable assemblies. Engineering studies have confirmed that the absolute best RF connections for double-shielded cables like LMR-400 and DXE-400MAX are made by crimping the shield, not soldering. However, most PL-259 crimped center pins aren't large enough and don't have enough contact area, which affects reliability. DX Engineering has solved those issues with these custom-designed connectors that we introduced on DX Engineering DX Series Coaxial Cable Assemblies. These PL-259s have soldered center pins that are full length and full diameter, so they connect properly, even with worn SO-239s. DX Engineering Next Generation PL-259CS8U series connectors achieve exceptional RF performance and power handling with these features: * All silver-plated brass shell and body * Silver-plated center pin securely mounted in PTFE dielectric * Center pin accepts large conductors and scalloped-tip allows generous solder flow * Crimped shield connection provides maximum reliability for all cables * Deep, double-knurled threaded shells for secure finger tightening * Fits all RG-8U size cables with center conductors up to 10 AWG including DXE-400MAX and LMR-400 as well as RG-213U, RG-11U and many others, including Belden 7810A, 8214, 8267 and 8237, 9913 and 9913F7. * Available in packages of 6, 12 or 24 connectors NOTE: DX Engineering offers reasonably priced, professional grade cable prep and connector crimping tools for an entire range of cables and connectors. Click "More Details" and the "Suggested Parts" tab to see available related products. Now you don't have to use the same old PL-259s. These advanced-technology PL-259 connectors let you build the highest quality coaxial cable assemblies. We designed them to be strong and lightweight and they represent a landmark improvement over decades-old, unchanged connector designs. This time, new IS better! Order DX Engineering Next Generation Crimp/Solder 8U UHF Male Connectors today and take advantage of DX Engineering innovations in RF connectivity! **U.S. Patent D745849
( 230 )
$39.99
LDG Electronics RU-9:1 Unun
LDG Electronics RU-9:1 Unun was designed to allow easy interface of random length vertical and end fed antennas to the LDG line of Automatic Antenna Tuners. This 200 watt Unun also operates as a standalone, meaning that it does not necessarily require a tuner for use on a certain antenna. It may be used with many of your antenna projects where a 4:1 Unun is typically recommended. This model is small and easy to weatherproof for use in the elements. LDG RU-9:1 Unun specs: * Ratio: 9:1 * Frequency coverage: 1.8 to 30 MHz. * Power range: Up to 200 watts PEP * Enclosure dimensions (WHD): 2.5 x 5 x 1.25 in. * Weight: 6 oz.
( 96 )
$29.99
LDG Electronics RU-1:1 Unun
LDG Electronics RU-1:1 Unun is intended to help remove unwanted RF from the coax cable shield. It is normally used as a common-mode RF choke for short coax cable runs or non-resonant antennas. The RU-1:1 features SO-239s for input and output. RU-1:1 Unun Specs: * Ratio: 1:1 * Frequency coverage: 1.8 to 30 MHz. * Power range: Up to 200 watts PEP * Enclosure dimensions (WHD): 2.5 x 5 x 1.25 in. * Weight: 6 oz.
( 57 )
$29.99
DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits
DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits are ready to help you make professional quality crimped coaxial cable assemblies, Powerpole® connections and many other popular-size wire terminations. Ultra-Grip 2 Crimp Tools are precision made heavy-duty commercial grade hand crimp tools. They are multi-purpose interchangeable-die tools made from high-quality carbon steel with a tough black-oxide finish for corrosion resistance and durability. These easy-to-use ratcheting crimpers are ergonomically shaped to produce extra manual power, with soft non-slip dual-color thermoplastic rubber grips for comfortable and positive connector crimping results. Ultra-Grip 2's integral ratcheting mechanism lets you make 'semi-automatic' perfect crimps, again and again, with any of the available dies for RF connectors and wire terminations. One of or DXE-UT-CRMP2 Crimp Tools is supplied with the DXE-UT-DIE-8U Crimp Die for RG-8U/213/LMR-400 size cable. The included 2.5 mm Allen wrench is used to change to one of the other optional die sets. Other sets cover the most popular sizes of coaxial cables with ten different Amphenol Connex crimp connectors in UHF Male/PL-259, Type N, BNC; Powerpole® connector sizes 15, 30 and 45 Ampere connectors, Molex connector pins, insulated crimp type connectors for 22-18/16-14/12-10 AWG and un-insulated crimp type connectors for 20-18/16-14/12-10 and 8 AWG. Our crimp tool and dies are compatible with major brand crimp tool manufacturers. DX Engineering Ultra-Grip 2 Crimp Connector Hand Tool Kits, model DXE-UT-KIT-CRMP2, provides a handsome, convenient carrying case furnished with the Ultra-Grip 2 Crimp Connector Hand Tool, cable shears, braid trimming tool and ALL FIVE CRIMP DIE SETS with a precut foam insert providing a home for each tool and die set. Coaxial cable connector crimping dies are cut to enable crimping both the ferrule and the center pin. DXE-UT-CRMP2 Crimp Tools, sold individually, include one set of DXE-UT-DIE-8U Crimp Dies for RG-8U/213/LMR-400 size cable. DXE-UT-KIT-CRMP2 Complete Kits contain: * DXE-UT-CRMP2 Ultra-Grip 2 Crimp Connector Hand Tool * DXE-UT-DIE-8U Crimp Die works on connectors for RG-8U/213/LMR-400 size cable * DXE-UT-DIE-8X Crimp Die works on connectors for RG-8X/LMR-240 AND RG-58/LMR-195 size cable * DXE-UT-DIE-PP Crimp Die for Powerpole® 15, 30, 45A contacts and Molex connector pins * DXE-UT-DIE-INS for insulated crimp style terminals 22-18/15-14/12-10 AWG * DXE-UT-DIE-UNIS for uninsulated crimp style terminals 20-28/26-24/12-10/8 AWG * CNL-911 Coaxial cable shears * DXE-170M Precision braid trimmers * 2.5 mm Allen Wrench * DXE-CRIMP-CASE Custom Tool Case Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Here is a link to a "how-to" video about using DX Engineering Cable Prep and Crimp Tools for Crimp Connectors by Randy, K7AGE: https://youtu.be/T6sYL_eJFaQ Not only are these DX Engineering Ultra-Grip 2 Crimp Connector Hand Tools and Tool Kits perfect for helping you make quality crimps and keeping track of your tools, but they also make it easy for you to duplicate quality crimps every time.
( 126 )
$40.99
DX Engineering OTMC-250P Mounting Clamp Kits
DX Engineering OTMC-250P Mounting Clamp Kits are versatile double-V saddle clamp and hardware sets that mount a pipe or tube to a plate with extreme security. Featuring two folded stainless steel toothed-V saddles with multiple points of grip, these clamps provide superior clamping and holding power than generic U-bolts. Designed for the DX Engineering OMNI-TILT™ Tilt Bases, all stainless steel OTMC Mounting Clamp Kits may be used in many applications for mounting antennas and other apparatus to pipes and tubing. These clamps can mount pipes and tubing ranging from 1-1/4 up to 2-1/2 inches OD (outside diameter); another important feature of these ingenious clamps. DX Engineering OTMC-250P Mounting Clamp Kits, model DXE-OTMC-250P contain all of these parts: 2 each - Toothed V-Saddles, Stainless Steel, clamps 1-1/4 to 2-1/2 in. OD 2 each - Hex Head Bolt, Full Thread, Stainless Steel, 5/16 in. -18 tpi x 4-1/2 in. length. 4 each – Flat Washer, Stainless Steel, 5/16 in. 2 each - Split Lock Washer, Stainless Steel, 5/16 in. 2 each - Hex Nut, Stainless Steel, 5/16 in. -18 tpi. NOTE: The parts in this kit (listed above) allow you to assemble 1 (one) complete clamp. If you need two of these clamps for your project, you will need to purchase 2 (two) of these kits. Put the clamping power of DX Engineering OTMC-250P Mounting Clamps to use on your next project. Order DXE-OTMC-250P now!
( 33 )
$31.99
Grommet Assortment Kits
Need to replace a grommet? These Summit Racing Rubber Grommet Assortment Kits will help you replace many grommets with ease. These kits feature the most commonly used grommet sizes. To make grommet selection easier, these kits include the three key measurements: The OD of your wire or cables; the pass-through wall thickness allowable and the ID of the hole to be used. Sorted into a convenient plastic case by size, these Summit Racing Rubber Grommet Assortment Kits are just the ticket for repairs, replacements and restoration projects.
( 2 )
$25.99
—
$29.99
DX Engineering Coaxial RF Connector Adapters
DX Engineering Coaxial RF Connector Adapters feature a wide selection of high-quality coaxial adapters. These adapters are used for changing connectors to different types and genders as well as connecting RF cables and equipment with different types of connectors. Type N, UHF Male (PL-259), UHF Female (SO-239), BNC, Type F and mini-UHF adapters, DX Engineering Coaxial RF Connector Adapters are available to complete your RF connections. You never know when you will need one, so order several today!
( 232 )
$21.99
—
$44.99
Times Microwave Systems® Coaxial Connectors
Times Microwave Systems Coaxial Connectors are innovative designs of the highest quality. Using genuine LMR® connectors and tools will assure reliable connections and quality you can trust. Times Microwave Systems LMR connectors are designed to work perfectly with LMR cables, so choosing and using Times connectors and termination tools assures reliable connections and puts Times quality you can trust to work for you. Although LMR cables through LMR-400 work with just about any manufacturer's connectors, LMR-600 cable requires Times Microwave Systems coaxial connectors. Order your cable and quality Times Microwave Systems Coaxial Connectors from DX Engineering! LMR® is a registered trademark of Times Microwave Systems.
( 38 )
$20.19
—
$49.15
Jet-Lube SS-30 Pure Copper Anti-Seize
Jet-Lube SS-30 Pure Copper Anti-Seize is the top choice of engineers and technicians in government, industry and leading Amateur Radio contest stations, for protecting mechanical assemblies of aluminum tubing, general hardware and copper grounding systems! On bonded metal surfaces Jet-Lube SS-30 assures electrical and RF conductivity while preventing oxidation and corrosion. Surpassing the capabilities of other aluminum anti-oxidants, the wide temperature range of Jet-Lube SS-30 prevents long-term drying and caking, and allows easy disassembly and effortless cleaning of parts. Jet-Lube SS-30 Pure Copper Anti-Seize is designed for use on taps, lugs, wiping contacts, drum switches, slip rings, and more. An environmentally preferred thread lubricant and conductive termination compound, Jet-Lube SS-30 helps keep your equipment in serviceable condition. It contains a high concentration of copper flakes (a requirement for heavy loads or compression) yielding controlled frictional characteristics that allow the surfaces of nuts and bolts to be easily tightened to their design torque specifications. This anti-seize product assures full hydraulic efficiency by allowing the metal surfaces to slide over each other without damaging metal-to-metal contact. Jet-Lube SS-30 is also designed to work as a similar and dissimilar component between two metal surfaces to prevent seizing and galvanic action. The SS-30 compound formula improves conductivity and ground continuity--and will not melt in high temperatures. Jet-Lube SS-30 Pure Copper Anti-Seize features include: * Meets MIL-PRF-907E spec * K-factor: 0.13 * Service rating: -65 degrees F (-54 degrees C) to 1800 degrees F (820 degrees C) * SS-30 Resistivity (Ohm-CM x108) 5 * Available in 0.25 and 0.50 lb. sizes Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Jet-Lube SS-30 Pure Copper Anti-Seize is perfect for building aluminum antennas, copper grounding systems, or as a general anti-seize for aluminum, stainless steel, steel, bronze, tin, brass, copper and galvanized hardware. Keep a supply of Jet-Lube SS-30 Pure Copper Anti-Seize on hand by ordering some from DX Engineering today!
( 67 )
$39.99
LDG Electronics RU-4:1 200 Watt UNUNs
These LDG RU-4:1 200 Watt UNUNs were designed to allow for an easy interface of 43 ft., non-resonant vertical antennas to antenna tuners via 50-ohm coaxial cable. These 200 watt peak-power UNUNs also allow for the easy matching of resonant verticals--in many cases, without the use of an antenna tuner! They may also be used with many of your antenna projects where a 4:1 match is needed. When you are looking for an inexpensive solution to your antenna matching needs, these LDG RU-4:1 200 Watt UNUNs from DX Engineering are real matchmakers!
( 26 )
$29.99
Amphenol RF Type N Male Crimp Connectors
Amphenol RF Type N Male Crimp Connectors are precision 50-ohm RF coaxial connectors that provide a positive, secure connection for your coaxial cable. Choose one of these different versions of the Type N connectors for your applications: 172102H-2 is our two-pack of the 172102-243 which has a larger center pin ID for DXE-400MAX and LMR-400. They work for 0.405 in. coaxial cables with larger 10 AWG through 11 AWG center conductor, including DXE-8U, some RG-8U, 8214, 9913, etc. 172102-2 is our two-pack of the 172102 that has the standard center pin that fits some RG-8U and RG-213 with smaller center conductors of 12 AWG, 12.5 AWG and 13 AWG. 172100-2 is our two-pack of the 172100 with the standard center pin for RG-58, LMR-195 and RG-400 (not 400MAX) size cables. N-Type connectors are designed to satisfy the need for a durable, weatherproof, medium-size RF connector with consistent performance through 11 GHz. Amphenol RF N-Type connectors feature threaded coupling mechanisms and are fully interchangeable with N-Type connectors made to the MIL-C-39012 specification. These connectors are used in all systems where excellent RF and mechanical performance is critical. Amphenol RF N-Type connectors have high-quality gold-plated center pins to ensure the best performance for any application. They are sold as a pair. Amphenol RF connector details: * Description: Coaxial connector, N-Male * Body Material: Brass * Body Plating: White Bronze * Body Style: Straight * Contact Material: Gold-plated brass * Maximum Frequency: 11 GHz * Dielectric: PTFE * Gender: male (Plug) * Impedance: 50 Ohms Choose the coaxial connectors you need from our wide selection of coax adapters and connectors. When you need Type- N Male connectors, Amphenol RF Type N Male Crimp Connectors are always a good choice. Order yours from DX Engineering today!
( 27 )
$20.99
—
$28.49
Summit Racing™ Foldable Kneeling Mats
Summit Racing™ foldable kneeling mats are made with non-recycled, non-toxic, and high-density foam material to provide better and stronger support for knees. It can help remove stress, discomfort, and pressure, allowing you to focus more on your task. The kneeling pad overall dimensions are 4 ft. long by 15.74 in. wide and 1.18 in. thick. Each pad is big enough to offer sufficient room for both your knees when kneeling and bending. The high-density PE foam has good water resistance, ensuring that it will remain clean and dry. And thanks to its high-density foam, the mats have great compression resistance; they won't compress, crack, or become flattened or deformed over time. The double-sided anti-slippery and cross-pattern design pattern ensures that it will not slip even when used in wet areas. A built-in handle on one side makes it easy to take the mat with you. These portable mats can be used for all kinds of hard, uneven surfaces. They're ideal for garage, workshop repairing, home installation, and more.
Not Yet Reviewed
$29.99
Icom IC-7110 HF/VHF/UHF All Mode Transceiver Reservation
Introducing the new Icom IC-7110, a versatile all-band, all-mode transceiver engineered for Amateur Radio operators who demand premium performance across every operating environment. Covering HF, 50 MHz, 144 MHz, and 430/440 MHz bands with support for SSB, CW, RTTY, AM, FM, and D-STAR digital voice operation, the IC-7110 delivers powerful 100-watt output on HF and 50 MHz and 50 watts on VHF/UHF. Its advanced dual-receiver architecture enables true HF/VHF or HF/UHF dual-watch capability, allowing operators to monitor multiple bands simultaneously while maintaining independent operating modes for each receiver. At the heart of the IC-7110 is a large 4.3-inch color touchscreen display featuring a real-time spectrum scope and waterfall display. Instantly identify open frequencies, monitor band activity, and visually track signal movement across the band with exceptional clarity. Whether chasing DX, contesting, or monitoring local repeaters, the intuitive display keeps critical operating information within easy reach. Digital mode enthusiasts will appreciate the IC-7110's simplified FT8 setup, which automatically configures the radio for FT8 operation with a single preset selection. Additional customizable presets provide flexibility for future digital modes, streamlining station setup and reducing configuration time. CW operators benefit from the integrated CW decoder technology derived from Icom's acclaimed IC-7300 series, offering adjustable decoding parameters to optimize performance under varying band conditions. The IC-7110 also delivers comprehensive D-STAR functionality, including DR mode, Terminal Mode, Access Point Mode, DV repeater monitoring, and even picture transmission and reception directly from the radio. Built-in Wi-Fi® and Bluetooth® connectivity provides seamless integration with smartphones, computers, and wireless headsets, while enabling convenient online firmware and repeater database updates. Designed for today's connected Amateur Radio operator, the Icom IC-7110 combines advanced digital features, powerful multi-band coverage, intuitive touchscreen operation, and state-of-the-art spectrum analysis tools into a compact, modern transceiver ready for home, portable, mobile, and emergency communications applications. Whether you're exploring HF DX, local VHF/UHF activity, digital modes, or D-STAR networking, the IC-7110 is built to keep you connected wherever your operating adventures take you.
Not Yet Reviewed
$35.00
Heil Sound Hand Switches
Heil Sound HS-2 Hand Switches are ergonomically designed pistol-grip hand switches combining functionality with ease of use. A typical application would be to key a transceiver when using a microphone without PTT, or in a noisy environment where VOX operation is useless or erratic. They feature a pistol grip, so you can operate the switch as a trigger, rather than as a tiring thumb-operated push button. Heil Sound HS-2 pistol grip hand switches terminate in a 1/4 in. phone plug for connection to the 1/4 in. female pigtail of the Heil Microphone Adapter Cables and Headset Adapter Cables, thus providing push-to-talk (PTT) control of almost any transceiver and microphone combination. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you want total PTT control, Heil Sound HS-2 Hand Switches from DX Engineering are a great way to go!
( 80 )
$45.00
LDG Electronics 1:1 Current Baluns
LDG Electronics 1:1 Current Baluns were designed to allow for the easy interface of ladder line antennas and long wires with the LDG line of automatic antenna tuners. * Configuration: 1:1 Current Balun * Frequency Coverage: 1.8 to 30 MHz. * Power Range: 100W continuous or 200 watts PEP * Easy to weatherproof * Enclosure size: 5 x 2.5 x 1.25 in. * Weight: 6 oz. (including enclosure) These baluns operate "stand alone"; thus, they do not require an LDG tuner. They may be used with any of your longwire, random wire, or ladder line antenna projects. For low power operation it's hard to beat the value in LDG Electronics 1:1 Current Baluns from DX Engineering!
( 27 )
$29.99
Summit Racing™ 20V 4.0 Ah Lithium Rechargeable Battery Packs
One battery for many tools. Summit Racing™ 20V 4.0 Ah lithium rechargeable battery packs provide constant and consistent power for cordless tools. Designed for compatibility with Summit Racing™ impact wrenches and driver, drill, inflators, and more, our 20V Max lithium-ion batteries deliver durability and the runtime to meet your job's demands. Additional features include: * High-current protection * High-voltage protection * Low-voltage protection * Over heating protection * Charging and discharging protection * Short Circuit Protection
Not Yet Reviewed
$45.99
DX Engineering Coaxial Cable Prep Tools for Crimp Connectors
DX Engineering Coaxial Cable Prep Tools for Crimp Connectors are an easy way to prepare cable ends for RF crimp connectors. These are the tools to use for dual shield cables that require crimp connectors, as well as on single shield cables when you want to use crimp connectors. - Please CLICK or TAP on the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation.
( 175 )
$44.49
—
$44.99
DX Engineering Saddle Clamps
DX Engineering Saddle Clamps are the best designed and tested clamps you'll find anywhere! And, the selection is extensive! Designed specifically to fit and secure tubing to surfaces in antenna construction, our Saddle Clamps are built strong to prevent slippage. DX Engineering U-bolts and V-bolts are crafted from high-strength 18-8 stainless steel with enough length to attach to thick plates. Saddles are cast from high-strength 535.0 aluminum with a rippled surface for superb gripping plus superior anti-corrosion properties. Saddles are available with natural or powder coated finishes. Need to clamp steel pipe or ground rods? Choose our V-clamps with stainless steel saddles. They have serrated teeth for clamping to a pipe or rod securely. All saddle clamps include stainless steel flat washers, lock washers, and nuts. NOTE: Due to the nature of high-tolerance metals, especially stainless steel, this hardware requires the application of an anti-seize thread lubricant before assembly to prevent galling and seizing. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you need Saddle Clamps for your application, there's only one smart choice--clamp central at DX Engineering.
( 111 )
$23.49
—
$44.99
Summit Racing™ Solderless Heat Shrink Terminal Kits
Don't risk the integrity of your electrical system by using cheap electrical connectors. Our Summit Racing™ solderless heat shrink terminals are tougher than typical vinyl connectors, keeping your electrical connections secure, better insulated, and corrosion-free. They come with connectors from 22-18 gauge to 12-10 gauge--everything you need for your current (and future) wiring jobs.
( 1 )
$37.99
DX Engineering Aluminum Tubing
DX Engineering High-Strength Aluminum Tubes are ideal for your antenna building projects. It is made available in sizes that fit into and over the next, with close tolerances specifically designed for strength when joined and overlapping only by a few to several inches, to build Yagi, Moxon or vertical antenna elements. NOTE: This tubing is NOT intended for each size to telescope completely into the full length of the next; it cannot be used for telescopic mast building. DX Engineering aluminum tubing is manufactured to very close tolerances. This provides the greatest amount of surface contact between nesting tubes for mechanical and electrical stability. Due to the close tolerance, any burrs, dirt, grit or other foreign material, as well as dents, dings and unseen bending or crushing suffered during shipment will cause binding that prevents this aluminum tubing from fully nesting. 6063-T832 seamless drawn aluminum tubing is available in 3, 6 and 12 ft. lengths. 6063-T832 tubing provides good resistance to general corrosion, including stress corrosion cracking, and an excellent surface appearance. Use a series of 3 ft. lengths to build an element that tapers more quickly for lower wind-resistance applications. Use a series of 6 ft. lengths to make an element that tapers more slowly for greater strength and bandwidth. The 12 ft. lengths are great for HF Yagi construction. Most sizes (except 12 ft.) are available slit on one end for use with DX Engineering stainless steel element clamps. If un-slit ends are required for your applications, merely insert the slit end into the next larger size in the stack and use your own attachment method. 6063-T832 tubing features a 0.058 in. wall thickness and is available in 1/8 in. increments from 3/8 in. to 2-1/8 in. O.D. 3003-H14 drawn aluminum tubing features a 0.035 inch wall thickness and a 1/4 inch outside diameter. Each piece is supplied with non slit ends and is available in both 3 foot and 6 foot lengths, making them ideal for your antenna building projects. If your setup requires maximum strength at very long assembly lengths, then choose DX Engineering 6061-T8 tubing. This heavy-duty version features a 0.120 in. wall thickness and is available in 1/4 in. increments from 1-1/2 in. to 3 in. O.D. Packaged shipments of 6 ft. tubing have oversize shipping fees, regardless of the number of 6 ft. pieces. Therefore, order more 6 ft. pieces to spread oversize fees over more tubing for a more cost effective shipment. Tubing that is 12 ft. long MUST be shipped by truck freight. If you need many pieces of the same size in a 12 ft. tube length, then buying DX Engineering High-Strength Aluminum Tubing Bundles (elsewhere in our catalog) maximizes the economy of scale for your shipping costs. NOTE: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Order DX Engineering High-Strength Aluminum Tubing here.
( 133 )
$20.49
—
$49.49
DX Engineering Premium Antenna Wire
DX Engineering Premium Antenna Wire helps you achieve top performance and long, trouble-free operation at a very reasonable cost. This PVC-insulated 14 AWG stranded copper wire is comprised of 19 strands of 27 AWG solid copper. Its relaxed PVC insulation is UV-resistant and rolls out easily, unlike wire that is commonly available at "big-box" stores, which coils and kinks. Our antenna wire is well worth its price for its features, especially for ease in handling. Over a decade of successful wire antenna installations have proven this insulated copper wire is up to the task. Conservatively rated at 92.5 lbs. breaking strength, this wire is strong enough for virtually every wire antenna application. Suggested installation includes supporting the feedpoint to properly handle the weight of the feedline, and balun if used, so that the wires only need to support themselves. When placed under extreme stress, this copper wire will stretch before breaking, allowing it to serve in a longer lasting installation for wire antennas of almost any style. Available in several pre-cut coiled lengths as well as on 500 and 1,000 ft. rolls, UV-resistant black insulated 14 AWG stranded copper DX Engineering Antenna Wire lasts longer than bare wire exposed to the elements. Use it with confidence for your wire antenna projects and get on the air!
( 143 )
$22.49
—
$49.99