Filters
10 Results Found For "Tinned braid"
DX Engineering Tinned Copper Braid Assemblies
DX Engineering Tinned Copper Braid Assemblies are typically used for the proper grounding of individual pieces of electrical or electronic equipment to a common grounding bus, such as a copper strap or a thicker bus bar. DX Engineering tinned copper braid assemblies are used for industrial, commercial, and broadcasting applications inside of electrical racks, for the connection of sub-assemblies to a metal chassis or grounding point, and for any special application where a high-quality tinned copper braid assembly is required. Our assemblies are made with top-quality tinned copper braid of various widths and lengths, and most are terminated with machine-crimped and hand-soldered terminals. Some assemblies feature heat shrink tubing over the connections for strain relief and longevity. Be confident with your equipment and system grounding with the best--DX Engineering Tinned Copper Braid Assemblies.
( 95 )
$23.99
—
$31.99
DX Engineering Exhaust Grounding Kits
Eliminate stubborn noise in your mobile installation with DX Engineering Exhaust Grounding Kits. Many modern vehicles have individual injectors and spark plug coils for each cylinder. These units can create substantial pulses on the vehicle wiring against the ground system. Engine blocks often have a poor ground, so anything attached to them can become a radiator. The exhaust pipe is directly bolted to the engine and can be excited just like an antenna, radiating the pulsing noise. By using one of our exhaust grounding kits, you can eliminate noise from your mobile installation. All hardware in these kits is made from high quality stainless steel. Each kit includes: * Exhaust saddle clamp * 14 in. long x 0.75 in. wide x 0.125 in. thick tinned copper braid * 3/8 x 1 in. bolt * 3/8 nut * Three 3/8 external tooth washers * 3/8 flat washer * 3/8 split washer
( 5 )
$31.99
—
$34.99
DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies
Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849
( 324 )
$40.99
—
$44.99
DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies
DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!
( 33 )
$41.99
—
$45.99
Times Microwave Systems® Mid-span Coaxial Grounding Kits
Times Microwave Systems Mid-span Coaxial Grounding Kits let you ground the coaxial shield to any convenient location with a ground lug. This includes most grounding clamps, plates and fixtures. For towers, an additional tower leg clamp is usually required. After stripping the outer jacket with a mid-span stripping tool, a pre-formed metal strap is applied to the braid/shield and tightened down. This strap is then electrically and mechanically connected to the ground source with a ground lead assembly, providing an excellent ground for the shield. These mid-span shield-grounding kits include: (1) Pre-formed tinned copper ground strap (1) Ground lead assembly (2) 1/4 in. brass lock-washers (2) 1/4 in. brass nuts (1) Roll 2-1/2 in. x 24 in. (610mm) butyl mastic (1) Roll 3/4 in. x 20 ft. (6.1m) PVC tape (1) Heat shrink tube (1) Field-crimp 3/8 in. 2-hole lug (2) 3/8 in. x 1-1/4 in. slotted bolts (2) 3/8 in. lock-washers (2) 3/8 in. nuts (2) 3/8 in. flat-washers (1) Detailed assembly instructions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Their included weatherproofing materials provide long-lasting environmental protection to help maintain a reliable ground for your coax. Shop DX Engineering for Times Microwave Systems Mid-span Coaxial Grounding Kits! LMR® is a registered trademark of Times Microwave Systems.
( 4 )
$34.65
—
$45.99
DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies
DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies are very flexible, solid dielectric, braided shield cable intended for RF connections to SO-239 and BNC equipment and antennas. These assemblies are suitable for moderate-power applications where flexibility is a key consideration. NOTE: These premade cables come with either high quality, silver plated 83-1SP PL-259 or silver plated BNC Male connectors installed at each end of the DXE-58AU cable, for use on any equipment with SO-239 or BNC Female connectors. Slightly smaller than RG-8X cable, DX Engineering RG-58A/U Coaxial Cable Assemblies are made from our new-process DXE-58AU solid dielectric cable. Featuring a stranded tinned copper center conductor, a braided tinned copper shield and a standard Type I PVC jacket, our 58AU cable assemblies are intended for low to moderate power, test and mobile applications where short runs and flexibility are required. DX Engineering RG-58AU offers easy handling characteristics and good shielding. Plus, this solid dielectric cannot gather moisture and has longer viability than old RG-58 foam cables. INFO: Type-I PVC is not intended for permanent installation in outdoor locations where sun exposure is expected. This cable can last well over 10 years if it is protected from UV sunlight. Our RG-58AU Coaxial Cable Assemblies come complete with high-quality silver-plated Delrin-dielectric PL-259 or BNC male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. Their center conductors are hand soldered and inspected. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. When you are looking for lightweight and flexible pre-assembled cable assemblies and want a high-quality, reliable product, look no further than our own DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies.
( 1 )
$34.99
—
$45.99
Clearance
Georgia Copper Flexible Ground Strap Jumpers
Georgia Copper Flexible Ground Strap Jumpers are excellent for low impedance outdoor grounding and HF antenna feedpoint and radial system connections. Even weathered to a dull patina, copper strap does not lose its low impedance advantages over wire or cables, for DC and AC through HF and VHF. Plus, flexible copper strap is far superior to tinned copper braid, which holds moisture and disintegrates which causes a undesirable increase in connection impedance over a relatively short time. Flexible SOLID Copper Strap Jumpers come in pre-cut lengths at 1 in. or 3/4 in. widths and 0.022 in. thickness, punched with 0.280 in. holes at each end, to accommodate 1/4 in. bolts. They're available in two-packs at six different lengths, 6 in., 12 in., 24 in., 36 in., 48 in., 72 in. and also in a variety pack that contains one piece of all six lengths. Order and use any of these specific length straps for your project. Or, use your tin snips and your imagination to make all types of low impedance connections for surge protection grounding boxes and panels, protectors, equipment racks, vertical antenna feedpoints, radial system connections and antenna feedpoint connections from a bolt terminal balun to the driven elements. This pre-cut copper strap may also be used as a shack ground bus or for the bus bar connection to the station ground rod or rods. Hobbyists and Electricians order extra copper straps to have on hand and be ready for those grounding and antenna connection projects that come up. Georgia Copper Ground Strap Jumpers are here at DX Engineering, ready for your needs.
( 10 )
$39.99
$21.99
—
$49.99
DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies
DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are available in several useful lengths, terminated with DX Engineering Next Generation PL-259 connectors; ultra-high quality all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. DX Engineering Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that fully engage even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and adhesive heat-shrink weather-sealed for the ultimate in service longevity Times Microwave Coaxial Cables are recognized as superior RF cable products. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center conductor, a gas foam polyethylene dielectric, and a rubber-like black thermoplastic elastomer jacket designed for repeated bending. LMR®'s RF shielding is typically 50 dB greater than off-brand single braided shield coax. LMR® UltraFlex copper braid and multi-ply bonded foil outer conductor shields provide greater than 90dB shielding. That is better than 180 dB isolation between two adjacent LMR® cables. DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are an excellent choice for a variety of indoor, mobile, portable, and outdoor applications.
( 1 )
$42.99
—
$47.99
Heil Sound Heil Wire Microphone Cable
Heil Sound Heilwire Microphone Cable is a specially-designed cable ideal for connecting microphones, foot switches, keyer paddles, and other audio, data or control devices. Heilwire features two 18-gauge wires inside a 100% coverage silver-plated braid shield, plus two 18-gauge wires external to the braid, for PTT or other control purposes. This design reduces capacitive coupling between the control lines and the sensitive AC audio signals residing inside the shield, resulting in significant reduction of the possibility of hum pickup, PTT pulses or RFI. Heilwire has an outer jacket made with extra flexible PVC and has a specified outer diameter of 1/4 in. to fit perfectly inside Heil Sound connectors. Heilwire Microphone Cable is great for many different types of audio and switching connectors and applications. For making connections to microphones and other devices, Heil Sound's exclusive Heilwire is the best choice. Get some today from DX Engineering.
( 7 )
$30.00
Sierra Radio Systems Coax Cables
Sierra Radio Systems Coax Cables are pre-terminated, 6 foot runs of LMR-195 with a BNC Male on one end and a PL-259 on the other. The cable is ready to use with the Sierra Radio Systems Coax Switch module.
Not Yet Reviewed
$29.00