Availability
6 Results Found For "preamp"
DX Engineering RPA-2 Modular Receive Preamplifiers
DX Engineering RPA-2 Modular Receive Preamplifiers are newly designed versions of the RPA-1 with internal slots for accessory modules. They accommodate the addition of the one optional plug-in module, such as the 75 to 50 ohm Impedance Transformer Module, or the Receiver Guard 5000HD Plug-In Module, or the DX Engineering Clifton Laboratories Z10020 AM Band Filter Module. DXE-RPA-2 preamps have very low internal noise and are optimized for the 300 kHz to 35 MHz range. They help you hear the weakest signals without artificially raising the noise. Meticulous craftsmanship and durable, robust components allow these preamplifiers to withstand high signal levels while providing superior dynamic range and third-order intercept performance that equals or exceeds most receiver and transceiver front-ends. RPA-2 Receive Preamplifiers have key features added, as requested by our tech-oriented customers and enthusiasts: - Internal slot accommodates the optional 75 to 50 ohm Impedance Transformer Module to accomplish typical receive antenna feedline to equipment transitions without losses -Also allows direct connection to 50 ohm receive antenna feedline BNC connectors with no transformer required - Internal slot for DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module – Front-end protection for the RPA-2 - Secure BNC female connectors and receive-system friendly F female connectors remain; both prevent accidental connection to transmitting devices with UHF connectors - A green LED indicates when DC power is present and the preamplifier circuit is engaged. - An ingenious positive-capture threaded-sleeve 2.1 mm power connector that ensures the DC power cannot be accidentally disconnected from the RPA-2. - Alternatively, a simple internal jumper change allows the RPA-2 to be powered by DC on the feedline While many other common preamplifiers suffer from harmonic distortion, RPA-2 Modular Receive Preamplifiers include our exclusive, advanced push-pull design that eliminates harmonic distortion. Their high quiescent current increases their ability to handle strong signals without distortion or overload. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 Vdc input. Please do not use a cheap wall transformer or noisy switching wall-wart to power these top-of-the-line preamplifiers. Indoor installation at the back of the radio is recommended for RPA-2. For those who want to place them in an enclosure at a receive antenna system, a handy internal jumper allows these new units to be powered on the coaxial cable. RPA-2 Receive Preamplifier Specifications: -Input and Output Connectors, female: BNC and F -Frequency Range: 300 kHz to 35 MHz -Gain: 16 dB, +/- 1.5 dB (over entire frequency range) -Output Third Order Intercept: 43 dBm -Noise Figure: 3.5 dB -One dB Compression Point: +26 dBm (400 mW output) -Dynamic Range, IM3: 110 dB or greater (500 Hz bandwidth) -Power Requirement: 12-18 Vdc, 140 mA max. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering RPA-2 Modular Receive Preamplifiers offer superior receiving results on crowded medium wave and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the advanced operational performance of DX Engineering Receive Preamplifiers. You will be able to pull in the weakest signals and snag that rare one, under the most difficult conditions, when you need it the most. Order your DX Engineering RPA-2 today!
( 14 )
$269.99
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$275.99
—
$464.45
DX Engineering Beverage Antenna System Combos
DX Engineering Beverage Antenna System Combos are single-wire single-direction Beverage antenna feed systems. These combos include DX Engineering's superb receive preamp and the Beverage antenna feedpoint transformer! The included BFS-1 transformer design makes them immune to the strong signal overload and core saturation. The isolated-winding matching transformer significantly increases the signal-to-noise ratio in Beverage and other high-impedance antennas. The included termination resistor is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes. Also included, the DXE-RPA-2 Modular Receive Preamplifier is the best low noise, receive preamps available… period. It is optimized for the 300 kHz through 35 MHz frequency range with an advanced push-pull amplifier design that eliminates harmonic distortion and it handles strong signals without distortion or overload. The DXE-RPA-2 Modular Preamp features one internal option slot for a plug-in module. Choose from the DXE-RG5000HD-PM Receiver Guard, the DXE-IT-PM 75 to 50 ohm Impedance Transformer, or use a RXFL Filter Adapter and a Receive Filter board for band pass, high pass or low pass filtering. Click "More Detail" for additional information. The "Documentation" tab contains links to associated files. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Beverage Antenna System Combos to get excellent MW and HF reception with your Beverage antenna.. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$385.98
DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable
DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable is our top-of-the-line, direct-bury RG-6. It has low RF signal loss and provides greater protection against electromagnetic interference. Available cut-to-length by-the-foot or in 1,000 ft. spools, this is the best ultra-high quality RG-6/U self-healing quad-shield cable solution. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. DXE-RG-6UFQ cable is ideal for many receiving applications including active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution and satellite radio installations such as Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up through microwave frequencies of satellite radio systems! Our RG-6 flooded quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding. The waterproof UV protected black jacket is made with a tough and flexible polyethylene (PE). This cable is infused with a flooding compound that provides a permanent barrier to moisture and is self-healing to minor cuts. The nominal impedance of DXE-RG-6UFQ cable is 75 ohms with a nominal Velocity Factor of 82% (VF = 0.82). The minimum bend radius is 2.500 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? DX Engineering RG-6U 75-ohm Flooded Quad-Shield Coaxial Cable is absolutely the best RG-6 quad-shield cable available and it is RoHS compliant! Check these super low attenuation figures! 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? If so, then order the new benchmark in RG-6 cable: DX Engineering RG-6U 75-ohm Flooded Quad Shield Coax. Your efforts will be rewarded with the results that you expect, using the best cable from DX Engineering.
( 8 )
$255.99
DX Engineering RTR-2 Modular Receive-Transmit Interfaces
DX Engineering RTR-2 Modular Receive-Transmit Interfaces provide the easiest and safest method for connecting a dedicated receive antenna to an HF transceiver that does not have a separate receive antenna input. Placed inline with the transceiver's antenna connector, the RTR-2 does the job of a 200 watt T/R relay using the amplifier keying line for failsafe protection, so your transmitted energy cannot go to the receive antenna. Three internal Plug-in Module option slots provide added features and protection: * DXE-RPA-2-PM Receive Preamplifier Plug-in Module * DXE-TRI-PM Transmit Receive Interrupter Plug-In Module * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-in Module DX Engineering RTR-2 Modular Receive-Transmit Interfaces allow the standard transceiver owner to enjoy the advantages of separate receive antennas. For the unswitched receive antenna (RX ANT) port on expensive transceivers, the RTR-2 interface also adds inexpensive failsafe protection. The receive antenna line can be opened or grounded with the optional DXE-TRI-PM Interrupter plug-in module. The RTR-2 is a very useful device for many applications, including: * Connection of external receiving antennas to transceivers lacking external antenna ports * T-R antenna switch for older equipment using separate transmitters and receivers * Interfacing antennas to older phasing or noise cancelling systems * Addition of a switchable receive preamplifier to any transceiver or transmitter and receiver combination * Excellent failsafe receiver protection for close-spaced transmit and receive antennas, without performance degradation of diode circuits of other devices. RTR-2 units feature a unique, failsafe connection method that prevents the hot switching and timing errors that are common on other transmit/receive relays. RTR-2 interfaces switch fast enough for partial break-in CW operation. There are many simple applications for the new RTR-2 and now internal modules can add dramatically improved reception of those really weak signals on the crowded HF bands! DX Engineering RTR-2 Modular Receive-Transmit Interfaces enable operators to enjoy improved reception with any low noise receiving antenna system. This shielded enclosure relay system provides a safe method of connecting a receive antenna, such as a Beverage, Active Receive system, or other receiving accessories to your radio. Major features that make the DX Engineering RTR-2 Receive Antenna Interfaces your best choice for a receive T/R system device: * New Status Indicating Color-changing LEDs * Three internal slots for new DX Engineering modules * New Key Line Out connector for Amplifier * New internal jumper for placing DC on the Receive Antenna feedline for Active or Loop receive antennas * Attractive and heavy stainless steel enclosure * 200 watts RF switching capability * Supports CW partial break-in * Main transmit antenna connector is SO-239 (UHF female) * Radio RF connector is SO-239 (UHF female) * Receive antenna input is 75 ohm F connector * Receive outputs are standard 75 ohm Type F connectors * Inputs are 50 ohm BNC or 75 ohm F (Optional transformer module available) * Safe switching--transmit antenna is always connected to transceiver on power-off * Hot switching lockout--disables receive antenna during transmit mode (Optional DXE-TRI-PM can be set to short the RX ANT line) * Versatile--allows inclusion of Optional RF preamplifiers and other plug-in modules * Simple 13.8 Vdc input for all operations An indispensable accessory for the DX enthusiast and useful for any Amateur's shack, DX Engineering RTR-2 Modular Receive-Transmit Interfaces can help you expand and improve your station's antenna connections and the protection of your equipment.
( 12 )
$375.99
DX Engineering Time Variable Sequencer Units
DX Engineering Time Variable Sequencer Units are microprocessor-based transmit/receive control signal-delay units. They can provide 0-30 milliseconds of delay, programmable in 2 milliseconds increments, to as many as five different outputs tied to your CW keying or push-to-talk (PTT) lines. By controlling the receive-to-transmit (and back) timing of linear amplifiers, and other sensitive equipment, damage caused by improper switch timing may be avoided. These DX Engineering TVSUs improve CW performance by eliminating the annoying leading-edge chopping or truncating of Morse characters, especially important in contests or pileups, where sending accuracy is critical. Now RoHS-compliant, they may also control external devices, such as preamps, active antennas, or external relays that need to have power removed during transmit. Separate power-in and power-out jacks on the front panel are used to control external power. Two 2.1mm power plugs and two 3.5mm stereo plugs are provided. Additional TVSU features include: * Control timing of PTT turn-on, hang delay of PTT, amplifier hang delay, external antenna relay hang delay, and turn-on delay of auxiliary output * Dip switch settable delays of 0-30ms in 2ms increments * Side tone generator that follows input of keyer or hand key, not transmitter * Side tone pitch can be programmed from 300 to 1,000 Hz in 50 Hz steps * Front panel headphone jack with adjustable volume * Supports CW full break-in * Can control external power to DX Engineering active receive antennas and thereby permit operation in closer proximity to transmit antennas Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. To make sure that all of your equipment keeps safely in step, use one of these DX Engineering Time Variable Sequencer Units!
( 1 )
$319.99