Availability
Antennas
Yaesu ATAS-120A Auto Active Tuning Antennas
Yaesu's patented ATAS™ Active Tuning Antenna System has been enhanced with the latest model: ATAS-120A. This is a unique mobile antenna that provides HF, VHF and UHF coverage with automatic motorized tuning. Designed for use exclusively with Yaesu transceivers that support ATAS, microprocessor controlled voltages are sent on the coaxial cable to adjust the antenna radiator length for best SWR. Yaesu ATAS-120A active tuning antennas cover the 7, 14, 21, 28, 50, 144 and 430 MHz Amateur bands and are compatible with the Yaesu FTX-1, FT891, FTDX-10, FT-710, FT-991A, FT-991, FT-857D, FT-897D, FT-100, FT-100D and the FT-450D. They are typically attached to a vehicle hatch or trunk lip UHF mount (not supplied), also available from DX Engineering. The ATAS-120A antennas were designed for mobile use, however they can be adapted for base, or portable operation with the appropriate mount and a substantial counterpoise radial wire system. Specifications of the Yaesu ATAS-120A Auto Active Tuning Antennas: * Operational Bands: 40, 20, 15, 10, 6 and 2 meters and 70 cm * Height, appx.: 4.59 to 5.25 ft. * Weight, appx.: 1.98 lbs. * Input Impedance: 50 ohms * Maximum Power: 120 Watts, SSB, CW, 50 percent duty cycle * Matched SWR: Less than 2.0:1 with proper grounding or counterpoise As with any HF, VHF and UHF mobile antenna, performance depends upon the grounding of the mount and bonding to the metal vehicle surfaces to create an optimal ground plane. Portable VHF and UHF operation is made possible with the addition of the optional Yaesu ATBK-100 Antenna Base Kit. This kit is not required, nor should it be used, for mobile operation. Operational convenience and performance is available for your Yaesu HF, VHF and UHF Mobile Transceiver. Order Yaesu ATAS-120A Active Tuning Antennas from DX Engineering.
( 50 )
$449.99
Yaesu G-450ADC Medium-Duty Rotator Systems
Yaesu G-450ADC Medium-Duty Rotator Systems are the entry-level rotator and controller that are perfect for small HF beams, a tri-bander or VHF and UHF antennas up to about 10 sq. ft. of tower-mounted wind load. A lesser wind load of about 5 sq. ft. can be handled when mounting the G-450ADC on top of a mast with the optional lower mast bracket, GC-038. Rotate Amateur and professional antennas with the Yaesu's handsome 120 Vac desktop remote control console, featuring a compass-style indicator at the station operating position. The G-450ADC rotator system provides 450 degrees of azimuth rotation in just over one minute. The rotator handles masts of 1.25 to 2.48 in. outside diameter and, when tower mounted, a total vertical mast load up to 200 lbs. In the Yaesu G-450ADC, the clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-450ADC Rotator motors and controllers operate with a 20 V DC control voltage, four-wire system, using the provided connectors to be installed at each end of the user supplied control cable, same as the previous models. For clarity, the new DC rotator motors are marked "G-450DC" at the connector. The rear panel of the controller is titled "G-450ADC" on the serial number label. WARNING: The legacy Yaesu G-450A Rotator motors and controllers used a 26 VAC control voltage, five-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-450ADC components, which only use pins 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use four-conductor, 20 gauge control cable (4 x 20 AWG). If the rotator cable needs to be longer than 125 ft., then use four-conductor 18 gauge cable (4 x 18 AWG). The input voltage for the G-450ADC controller is labeled "117 VAC" to indicate house current of 110 to 120 Vac. When you need a medium-duty rotator system, which is durable and attractive, order a new Yaesu G-450ADC Medium-Duty Rotator System from DX Engineering.
( 46 )
$429.99
Comet CHA-250HD HF/VHF Vertical Antennas
Comet CHA-250HD HF/VHF Vertical Antennas is an updated design of the popular CHA-250B vertical antennas. These antennas make the most of a tight situation! - Please CLICK on the title of the product(s) listed for the Overview, Specifications, a complete Description and Suggested Parts. Links to instruction manuals also appear in the Documentation section.
( 41 )
$499.95
Chelegance MC-750 Portable HF Vertical Antennas
Chelegance MC-750 Portable HF Vertical Antennas feature a quick, no tools required antenna system that is easy to set up and disassemble covers 40 through 6 meters and will handle up to 100 watts. The antenna base with a built-in ground spike has a female SO-239 connector and jacks for up to 4 preassembled, 11.48 ft. counterpoise radials. The MC-750 functions as a quarter-wave vertical ground plane antenna for the 14 - 50 MHz frequency range while using the included 17 ft. telescoping whip. Install the supplied loading coil for operating in the 7 MHz/40M band. This vertical antenna kit comes packed in a handy carrying bag to keep things organized. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Additional Features and Specifications: * Antenna Base with Ground Spike * 7 Mhz Loading Coil * 1.64 ft. Extension * 17 ft. Telescopic Whip * 4 – 11.48 ft. Wire Radials * Cable Winder * Carrying Bag
( 49 )
$327.99
Alpha Antenna HF/VHF/UHF MagLoop EmComm Antennas
Alpha Antenna HF/VHF/UHF MagLoop EmComm Antennas are designed in an oval shape to maximize signal transmission skyward. These versatile antennas include a low-loss BNC coaxial feedline connector and built-in, removable tripod legs, making it ideal for various deployments such as balconies, desktops, parks (POTA), summits (SOTA), and similar operating locations.
( 7 )
$399.00
Buckmaster OCF Dipole Antennas
Buckmaster OCF Dipole Antennas are made from the best quality materials with a completely potted waterproof balun and no external connectors. They are designed to give you years of trouble-free service! Buckmaster antennas are shipped fully assembled, ready to deploy with no tuning or trimming required. Choose a model with a 300 watt balun or a 3,000 watt balun. Each has a weather protected SO-239 connector. They are offered in three lengths to operate in these bands: - 270 ft. models cover 160, 80/75, 40, 20, 17, 12, 10, 6 meters - 135 ft. models cover 80/75, 40, 20, 17, 12, 10, 6 meters - 68 ft. models cover 40, 20, 10 and 6 meters Classic OCF (Off-Center Fed) antennas, like Buckmaster, typically have the feedpoint at the 2/3 and 1/3 point on the overall half-wave wire antenna. That means one leg is twice as long as the other. They are intended to be installed with the feedpoint at 35 ft. and the ends at about 15 to 25 ft. However, other installations such as a horizontal "flat top" can work very well. A tuner may be required for best SWR. Buckmaster OCF Dipole Antennas are a very simple way to get on the air and work multiple bands… quickly! They are a great choice as a first antenna or as a supplement to others. Order your Buckmaster OCF Dipole from DX Engineering.
( 67 )
$276.00
—
$429.00
DX Engineering Pre-Assembled Radial Wire Kits
DX Engineering Pre-Assembled Radial Wire Kits have 1/4 in. ring terminals that are CRIMPED and SOLDERED onto one end of high quality 14-gauge stranded copper wire with UV black soft PVC insulation. They make the installation of your ground radial system fast and easy. The stranded wire and soft insulation means that the wire will lay flat as you place it on the ground for a simple, no-tangle installation and convenient attachment to your DX Engineering Radial Plate, model DXE-RADP-3. These radial wire kits are designed for users of vertical antenna systems that have the need for a high quality radial system for optimum antenna performance. These kits feature: * 20 radial wires of the same length in each package * 20-packs are offered in three lengths; 20 ft. (-20RT), 32 ft. (-32RT) and 65 ft. (-65RT) * 10-packs of 120 ft. radials for 160 meter verticals also available (-120RT) * 14 AWG, stranded copper wire * UV resistant black soft PVC insulation * 1/4 in. ring terminals are machine crimped and hand soldered onto each radial wire Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. An effective and efficient system of many radials dramatically improves vertical antenna performance. Give your vertical a boost with DX Engineering Pre-Assembled Radial Wire Kits!
( 29 )
$345.99
—
$425.99
Yaesu Rotator Units
Yaesu Rotator Units are available as replacements or as stand-alone azimuth positioners for use with a third party controller. They include only the top mast bracket and hardware. Lower mast brackets are sold separately.
( 19 )
$329.99
—
$389.99
DX Engineering MBVE-5A/AE Series SAF-T-TILT™ Vertical Antenna Components
DX Engineering MBVE-5A and MBVE-5AE Vertical Antenna Components are the specialized parts for these SAF-T-TILT™ antenna systems. Top tubing sets include hardware are used on both standard and extended base versions. Standard and extended base tubing and insulators use separate hardware sets included in antenna packages or sold separately. These components are original parts, which are also available here as replacements. These are genuine DX Engineering SAF-T-TILT™ Vertical Antenna Components.
( 7 )
$499.99
Comet GP-9 Dual-Band VHF/UHF Base Vertical Antennas
Comet GP-9 Dual-Band VHF/UHF Base Vertical Antennas provide very high gain on the 2-meter and 70-centimeter bands. These superior-quality base station antennas feature a three-piece, heavy duty, UV-stabilized fiberglass radome for many years of reliable service. With the highest power rating in their class, these base station antennas are ready to handle long QSOs from your high-power VHF/UHF radios. Although light in weight, they incorporate strong, easy-to-use, extruded aluminum and stainless steel clamp-on mounting hardware. While the standard GP-9 features an SO-239 style connector base, the GP-9N version is available with an N-Type female connector for maximum signal transfer! When you need to reach out with absolute maximum gain from your omnidirectional VHF/UHF base station antennas, remember that Comet GP-9 Dual-Band VHF/UHF Base Vertical Antennas were designed just for you!
( 52 )
$324.95
REZ Antenna Systems Recon 40 Version 2 High Performance HF Antenna Coils
REZ Antenna Systems Recon 40 Version 2 High Performance HF Antenna Coils are engineered for reliable HF operation across the 40–10 meter bands when paired with the REZ-Z17 17-foot telescoping whip (sold separately). Built with 14-gauge enameled copper wire, the Recon 40 handles up to 500W SSB, 300W CW, and 200W digital (50% duty cycle). Switching bands is effortless with the integrated weatherproof coil bypass switch—just flip the switch and adjust the whip for higher frequency operation.
( 3 )
$349.00
WiMo X-Quad Antennas
WiMo X-Quad Antennas, with separate monoband models for 144-146 MHz or 430-440 MHz, represent a refinement of VHF and UHF cross-polarized Yagis. They are well-known in Europe as "multi-element quads"—an antenna with aluminum elements, not a wire and fiberglass antenna—which offer excellent gain with a relatively short boom length. X-Quads are a great solution due to their short length and lightweight construction, especially for VHF/UHF satellite systems which require rotation in all compass directions and elevations. Two X-Quad Antennas, one for 144-146 MHz and one for 430-440 MHz, may be mounted at opposite ends of an azimuth-elevation rotator cross-boom for high-performance full duplex Satellite operations. For either or both bands, X-Quad Antennas may instead be used in a stationary mount, as pictured, for all-mode terrestrial operations. In either application, multiple X-Quad Antennas may be stacked vertically and horizontally for additional gain and tighter patterns. The WiMo X-Quad special features, developed specifically for Satellite Amateur Radio include: * Switchable Polarization Plane; horizontal/vertical/right hand circular/left hand circular (remote switching requires optional equipment) * High gain compared to other antenna forms due to the "stacking effect" * Short boom length and compact design * Back-end boom or mid-boom centered mounting to the mast is possible The radiator element is a "stacked quad" multi-element beam, for which linear polarization can be compared to a crossed slotted radiator. However, the advantage of the X-Quad is that it can be optimally used for the desired polarization by simply changing the feed. Compared to a typical cross-polarized Yagi, all directors and reflectors are active in the X-Quad, which enables the compact design. As with cross-polarized Yagis, switching is accomplished on the mono-band X-Quad either by a coaxial relay or with a band specific WiMo Remote Polarization Switch (sold separately). If the remote switch is mounted at the antenna, then only one coax cable and a 4-conductor control cable are required, sold separately. If the Switch is used at the station, then two coaxial cables from the antenna to the station are needed. The WiMo X-Quad Antenna can also be permanently set for circular operation by using an optional, band-specific Phase Line. The secondary elements are arranged diagonally in relation to the square-shaped driven element, which corresponds to the voltage distribution on the radiating element, for the most favorable results. In comparison to Yagi antennas, the X-Quad pattern and tuning are affected less by the influence of external fields, making them ideal for installation under a roof, in an attic space. All elements are electrically conductively connected with boom and cable outer sheath, thus eliminating interference from atmospheric noise. Two Type-N female coaxial connectors, one for each polarization, are mounted in a housing that is waterproof. Boom and elements are made of aluminum, all hardware is stainless steel. Construction and design of the antennas are protected by law (DBGM). The antennas are designed for boom-end mounting; however, alternatively the mast clamp can be mounted in the middle of a non-metallic boom. These antennas have a split boom, so their transport length is only 29.53 in. (75cm) for the 2m antenna and 25.59 in. (65cm) for the 70cm X-Quad. For portable operations they can be stowed away comfortably in the trunk of car and their shipping costs are comparatively low.
( 5 )
$349.99
ICOM AH-710 Folded Dipole Antennas
ICOM AH-710 Folded Dipole Antennas get you on the air--fast! You can cover all amateur bands and operate with up to 150 watts with these ICOM pre-assembled, multi-band folded dipole antennas. Designed to work with any ICOM amateur HF transceivers, including their marine transceivers, the AH-710 antennas can be installed in flat top or inverted V configurations. The specs for ICOM AH-710 folded dipole antennas are: * Frequency range: 1.9 to 30 MHz * Power rating: 150 W * Input impedance: 50-ohm connection * VSWR: Less than 2:1 (1.9 to 18 MHz) Less than 2.5:1 (18 to 30 MHz) * Length: 24.5 m (80.4 ft.) * Coaxial feed line: 30 m (98.4 ft.) with PL-259s * Support Rope: 10 m (32.8 ft.) white Nylon * Auto-bonding Tape: 30 cm ( 1 ft.)
( 13 )
$429.99
Hustler 6BTV 6-Band HF Vertical Antenna and DXE® Installation Guide Packages
Hustler 6BTV 6-Band HF Vertical Antenna and DXE® Installation Guide Packages are trapped-vertical antennas that provide an omni-directional pattern. 6BTVs were designed as self-supporting verticals to provide efficient operation in the 10, 15, 20, 30, 40, and 75 or 80 meter bands. These antennas perform well in restricted space areas. For peak performance, a field of radial wires should be used. Hustler 6-BTVs provide for automatic selection of bands through the use of optimum-Q traps which are individually and precisely tuned and internally sealed at the factory. These traps are parallel-tuned circuits, which provide very effective isolation between the vertical sections, permitting precise multi-band operation. Broadband operation, with low SWR over the entire ham band, (limited on 80 and 75 meters), is possible in a proper installation. These antennas were designed to provide optimum performance from both an electrical and mechanical standpoint. Mechanically, these antennas boast a heavy-duty base and heavy-duty aluminum tubing throughout. The mechanical assembly is accomplished with all stainless steel hardware. Performance provided by the Hustler 6BTVs is better than any other antenna of this type. Broad-banding is such that one measurement and setting permits both phone and CW operation. The antenna provides nominal 52-ohm base impedance when installed and tuned according to the instructions. The radiation efficiency is equal to, or greater than, other trap verticals. An optional DX Engineering Tilt Base allows the antennas to be easily brought down during non-operating times or for tuning and maintenance. Want a multi-band vertical antenna with a proven track record? Order Hustler 6BTV 6-Band HF Vertical Antenna and DXE® Installation Guide Packages from DX Engineering!
( 44 )
$499.98
DX Engineering RPA-2 Modular Receive Preamplifiers
DX Engineering RPA-2 Modular Receive Preamplifiers are newly designed versions of the RPA-1 with internal slots for accessory modules. They accommodate the addition of the one optional plug-in module, such as the 75 to 50 ohm Impedance Transformer Module, or the Receiver Guard 5000HD Plug-In Module, or the DX Engineering Clifton Laboratories Z10020 AM Band Filter Module. DXE-RPA-2 preamps have very low internal noise and are optimized for the 300 kHz to 35 MHz range. They help you hear the weakest signals without artificially raising the noise. Meticulous craftsmanship and durable, robust components allow these preamplifiers to withstand high signal levels while providing superior dynamic range and third-order intercept performance that equals or exceeds most receiver and transceiver front-ends. RPA-2 Receive Preamplifiers have key features added, as requested by our tech-oriented customers and enthusiasts: - Internal slot accommodates the optional 75 to 50 ohm Impedance Transformer Module to accomplish typical receive antenna feedline to equipment transitions without losses -Also allows direct connection to 50 ohm receive antenna feedline BNC connectors with no transformer required - Internal slot for DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module – Front-end protection for the RPA-2 - Secure BNC female connectors and receive-system friendly F female connectors remain; both prevent accidental connection to transmitting devices with UHF connectors - A green LED indicates when DC power is present and the preamplifier circuit is engaged. - An ingenious positive-capture threaded-sleeve 2.1 mm power connector that ensures the DC power cannot be accidentally disconnected from the RPA-2. - Alternatively, a simple internal jumper change allows the RPA-2 to be powered by DC on the feedline While many other common preamplifiers suffer from harmonic distortion, RPA-2 Modular Receive Preamplifiers include our exclusive, advanced push-pull design that eliminates harmonic distortion. Their high quiescent current increases their ability to handle strong signals without distortion or overload. These high performance devices must be powered with a well filtered and regulated DC power supply and will offer maximum performance at 12 to 18 Vdc input. Please do not use a cheap wall transformer or noisy switching wall-wart to power these top-of-the-line preamplifiers. Indoor installation at the back of the radio is recommended for RPA-2. For those who want to place them in an enclosure at a receive antenna system, a handy internal jumper allows these new units to be powered on the coaxial cable. RPA-2 Receive Preamplifier Specifications: -Input and Output Connectors, female: BNC and F -Frequency Range: 300 kHz to 35 MHz -Gain: 16 dB, +/- 1.5 dB (over entire frequency range) -Output Third Order Intercept: 43 dBm -Noise Figure: 3.5 dB -One dB Compression Point: +26 dBm (400 mW output) -Dynamic Range, IM3: 110 dB or greater (500 Hz bandwidth) -Power Requirement: 12-18 Vdc, 140 mA max. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. DX Engineering RPA-2 Modular Receive Preamplifiers offer superior receiving results on crowded medium wave and shortwave bands as well as on the ham bands. SWLs and Radio Amateurs around the world have come to rely on the advanced operational performance of DX Engineering Receive Preamplifiers. You will be able to pull in the weakest signals and snag that rare one, under the most difficult conditions, when you need it the most. Order your DX Engineering RPA-2 today!
( 14 )
$269.99
DX Engineering Vertical Ground Mount Tubing
DX Engineering Vertical Ground Mount Tubing is very high-strength 4130 Chromoly steel intended to be placed into a concrete foundation for the installation and support of large vertical antennas, tilt pivot bases and other antenna and mast tilt mounts. We have made these mounting masts the appropriate length for the intended installation and for common ground shipment at a reasonable cost; no more searching for a special pipe or paying high freight charges! Cut from our original 4130 Chromoly Masts that are nominally 22 ft., this high-strength galvanized steel tubing is available only in two tubing sizes at nominal lengths for the intended ground mount use. DXE-VGMT-2CG: 2.0 in. OD is about 5 ft.4 in. length, + or - 2 in. DXE-VGMT-3CG: 3.0 in. OD is about 7 ft. 3 in. length, + or - 3 in. Each tube features a 0.250 in. wall thickness and meets ASTM A-513 Type 5 ratings. They are cold-drawn, electric-weld, high-strength carbon-steel tubing with a yield stress rating of over 100,000 psi! Tensile strength minimum is above 110,000 psi. Minimum Rockwell B hardness is 96. They are temperature stress-relieved to ensure consistent mechanical strength. Galvanizing on these masts meets ASTM A123/A123M specifications. The surface finish has a nearly polished appearance. Cut ends have been sprayed with cold galvanizing to inhibit rust. Click on the More Detail link below to see specific DX Engineering pivot base, tilt base and vertical antenna model applications. Are you raising a BIG vertical or antenna mast? If you are going to crank up a large vertical antenna or antenna support mast that will put a LOT of torque on the pivot base or tilt base mount, then order DX Engineering Vertical Ground Mount Tubing for your antenna project and get it without paying truck freight!
( 7 )
$405.99
Yaesu SCU-LAN10 Network Remote Control System
Yaesu SCU-LAN10 Network Remote Control System brings the advanced functionality of Ethernet LAN port direct remote control to the unparalleled FTDX-101D and FTDX-101MP Transceivers and the impressive, compact and affordable FTDX10 Transceiver. All of the excitement of these phenomenal radios is available to any PC, on your local network or via the Internet from anywhere in the world, with the SCU-LAN10 interface units connected to the transceiver and a local network or the Internet. SCU-LAN10 Network Remote Control Software is available for download from www.yaesu.com Also available from the same link is the required Firmware Update versions listed here for the FTdx-101 series transceiver to be used with the SCU-LAN10 Interface: - MAIN: V01-14 - DISPLAY: V01-06 - IF DSP: V01-05 - SDR: V02-03 To confirm the firmware version on your FTdx-101 series transceiver, press [FUNC] key, touch [EXTENSION SETTING] and then select [Soft Version]. The software version will be displayed. All FTDX10 versions are supported. Each SCU-10LAN unit includes a special 13-pin DIN interface cable, a USB cable and two snap-on ferrite RFI suppressors. Specifications: Supply Voltage: 13.8 VDC Nominal Operating Voltage: 9 VDC to 15.2 VDC Current Consumption: 800 mA (max) Operating Temp Range: +32F-122F (0C to 50C) Dimensions: (WHD) 4.37 x 1.24 x 5.31 in. (111 x 31.5 x 135 mm) Weight: 0.93 lbs. (420g) NOTE: * A wired LAN port Ethernet router connection is required. Wi-Fi is not supported. * When using the internet, a fixed global IP address or fixed domain name is required for the network where the remote controlled radio is installed. Equip your Yaesu FTDX-101MP, FTDX-101D or FTDX10 transceiver for Internet LAN remote control operations with the Yaesu SCU-LAN10 Network Remote Control interface unit from DX Engineering.
( 5 )
$447.99
DX Engineering Bulk Radial Wire Kits
DX Engineering Bulk Radial Wire Kits will help you achieve optimal performance with a ground-mounted vertical and allow you to install as many radials as possible. These PVC-insulated stranded-copper radial wires are UV-resistant and roll out easily, unlike the wire that's commonly available at "big box" stores. Any type of ground-mounted vertical antenna—an Inverted L for instance—can usually benefit from the addition of a radial system. The increase in field currents provided by radials improves efficiency and antenna Q. Compared to bare wire, DX Engineering Bulk Radial Wire Kits will last much longer when exposed to the elements. These kits include either steel or biodegradable resin radial wire staples for holding down the radials until grass grows over them. The kits work extremely well with DX Engineering Radial Plates (DXE-RADP-3) to create a complete radial system. Biodegradable staples allow easy installation of radial wires and will degrade and disappear in about a year when they are no longer needed, making them environmentally friendly! Biodegradable staples are intended for softer ground, where they may be pushed or lightly tapped into the ground with a tool head. Since they are a resin material, the staples are subject to breaking in rocky or hard soil. They're not intended to be hammered in; if hammering is required for installation, you should use the steel wire staples. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. For easy installation of antenna radials, DX Engineering Bulk Radial Wire Kits provide the wire, ring terminals and lawn staples. Suggested as a station upgrade product; make more contacts to worldwide DX stations and DXpeditions.
( 17 )
$387.95
—
$393.95
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$275.99
—
$464.45
REZ Antenna Systems Ranger 80 II™ HF Tuning Coils
REZ Antenna Systems Ranger 80 II™ HF Tuning Coils are a base-loaded vertical coil designed for portable HF operations. It supports rapid deployment and is suitable for use in POTA, Field Day, and emergency communications. These antenna tuning coils are precision-machined in the USA from high-grade materials and operate from 80 to 6 meters when paired with a telescoping whip extended to at least 9.3 feet (sold separately). It supports up to 200 watts SSB and 100 watts digital (50% duty cycle). The updated Ranger 80 II™ features integrated radial ports and improved weather resistance and will accept up to eight 4mm banana plugs for fast, secure radial wire connections—no fumbling, just plug in and get on the air. The antenna coil mounts to a ground spike or [z]Pod™ (sold separately) using standard 3/8-24 hardware, making it compatible with many industry-standard mounting accessories for ultimate flexibility.
Not Yet Reviewed
$375.00
Hustler Base Model G6-270R Vertical Antennas
Hustler Base Model G6-270R Vertical Antennas are dual-band collinear designs using phased 5/8 wave elements on both bands. Two 5/8 wave elements are used on 2 meter bands, and four 5/8 wave elements are utilized on the UHF band. They offer a solid gain of 6dB on both bands for outstanding fringe-area performance. Featuring a one-piece tapered fiberglass radome, they eliminate the inter-modulation and mechanical problems associated with 2 and 3-piece UHF radome designs. Hustler G6-270R vertical antennas are shunt-fed and DC-grounded for lightning protection and static discharge and will survive winds of up to 100 mph. Hustler antennas have a long-standing reputation for high quality and exceptional craftsmanship. Order Hustler Base Model G6-270R Vertical Antennas from DX Engineering for your 2 meter and 70cm operations!
( 12 )
$494.99
Hustler G-3754 37-54 MHz Monoband Vertical Antennas
Hustler G-3754 37-54 MHz Monoband Vertical Antennas are full size 5/8 wave, 6 meter vertical antennas from Hustler. They were developed in the early 1970s and have been available ever since. Designed for commercial VHF and government VHF-Low Band use, they are extremely durable. They also provide gain of 6.4 dBi! A full size radiator with a lower radiation angle concentrates power closer to the horizon, where you want it. The elements are easily adjusted to any frequency from 37 through 54 MHz, so these antennas vary in height depending on the frequency to which they are tuned. For 6 meters, they are about 8.3 ft. tall. Tuned radials at the base of the vertical enhance electrical performance and help provide a 6 meter bandwidth of over 4.0 MHz with 2:1 SWR or less. An integral shunt-fed matching system also provides a DC path to ground to drain off static, resulting in extremely low-noise antennas. Hustler G-3754 antennas are a value-packed option for 6 meters and handle 300 watts CW/FM/AM. VHF verticals are usually mobile/repeater FM antennas but, due to their wideband coverage, you may want to use one of these in the SSB portion of the band. Purchase your Hustler G-3754 37-54 MHz Monoband Vertical Antennas from DX Engineering and start having more fun on 6 meters!
( 6 )
$398.99
Chameleon Antenna CHA-BV-SO239 HF Basic Vertical Antennas
The Chameleon Antenna CHA-BV-SO239 HF Basic Vertical Antenna system redefines versatility in portable antennas, offering an efficient and highly adaptable setup for single-band resonance from 40 - 6M. This antenna system is specifically engineered to meet the needs of field operators, emergency responders, and amateur radio enthusiasts who require reliable communication in varied environments.
( 1 )
$450.00
EAntenna HF Rotatable Antennas
EAntenna HF Rotatable Antennas include a comprehensive range of mono-band and multi-band Yagi beams and rotatable Delta Loops and Dipoles. Find the band coverage and performance antenna of your dreams right here. For example, the exciting EAntenna 59+ provides great performance on 20, 17, 15, 12 and 10 meters! Check out the specs on this great line of HF directional antennas. DX Engineering offers EAntenna because their attention to manufacturing detail is excellent! Their Yagi, log periodic, and rotatable dipole antennas are built with high-quality stainless steel hardware and aircraft-grade aluminum. As you look through these selections, be aware that advanced, cutting-edge computer modeling and optimization techniques were used to produce every one of the EAntenna premier HF beam antennas and state-of-the-art VHF and UHF Yagi antennas. Their mechanical designs are very robust in every way, as most are rated for at least 100 mph wind survival. To see additional information about each antenna, click on the "More Details" link on the antenna of interest. Then click the Specifications tab to see all of the physical and electrical characteristics of that antenna. EAntenna products are offered exclusively in North America by DX Engineering. Plus, we can ship these great antennas internationally! When you're making plans for a new antenna at your station, look no further for the outstanding solutions by EAntenna, "The Best Choice for Your Antenna System!" NOTE: Manuals are normally supplied bilingual. If your manual lacks an English section, contact DX Engineering for an English version.
( 47 )
$355.99
—
$499.99