Availability
2 Results Found For "75W"
LDG Electronics AT-200ProII Automatic Antenna Tuners
There was a time when 100 watts was a lot of power. Today, more and more transceivers feature 200 watts of output. Even though many of these modern radios feature a built-in tuner, the tuners' range and features are usually quite limited. Break through those barriers with LDG Electronics AT-200ProII Automatic Antenna Tuners! They're designed for this new generation of rigs and are specifically recommended for Ten-Tec and tube radios. Many QRP operators have a small 100-150 watt amplifier for times when you need a few more S-units. The AT-200ProII tuners are ideal for this kind of operation; their minimum required power is only 5 watts, but they will handle higher power as well. The AT-200ProII tuners will handle up to 250 watts SSB or CW (75 watts RTTY, FT8) on 1.8-30 MHz, and 100 watts on 54 MHz. They feature LDG's state-of-the-art, processor-controlled Switched-L tuner. The AT-200ProII tuners will match virtually any kind of coax-fed antenna, including Yagis, dipoles, inverted Vs, slopers, loops, or just about anything. They will typically match a 10:1 SWR down to 1.5:1 in just a few seconds. You can also use the AT-200ProIIs with end-fed antennas, random wires, and antennas fed with ladder line with the optional LDG balun. Operation couldn't be simpler--while transmitting a carrier, just press the tune button. An automatic tuning cycle will begin and then end a few seconds later with the tuners set at the lowest SWR (almost instant for frequencies stored in memory). The AT-200ProII automatic memory tuners are the latest in a long line of innovative LDG Electronics tuners and will allow you to get the most out of your Kenwood, Yaesu, Ten-Tec, or ICOM radio that operates at higher power. Additional features include: * 5 to 250 watts SSB and CW (100 watts on 6M, 75 watts HF Digital, RTTY, PSK, FT8) * Easy-to-read LED bar graph display for RF power, SWR, and status * LEDs for antenna position and bypass * 4,000 memories (2,000 for each antenna) for instantaneous band changing * 2-position antenna switch with memories for four antennas on each position * Tuning time: 0.5 to 6 seconds full tune, less than 0.1 second memory tune * Built-in frequency counter for memory operation * Tunes 6 to 800 ohm loads (16 to 150 ohms on 6m), 6 to 3,600 ohms with optional 4:1 balun * Includes 6 ft. DC power cable * Power requirements: 11 to 16V DC at 750 mA max during tuning * Weighs 2 lbs. Note: For additional information, please look at the files under the "Documentation" tab. If you are running an older, high-output tube rig, a newer 200 watt rig, or have a small amplifier to give your QRP rig a boost, consider LDG Electronics AT-200ProII Automatic Antenna Tuners from DX Engineering!
( 36 )
$349.99
Yaesu YA-30 Broadband HF Folded Dipole Antennas
Yaesu YA-30 Broadband HF Folded Dipole Antennas are compact folded dipole antennas. YA-30 Folded Dipoles not only cover 1.6 to 30 MHz, they handle RF power input of 150W PEP. Best of all, as with the majority of broadband antennas, no antenna tuner is required. These folded dipoles are multi-wire but relatively light in weight. By having only two stainless steel wires they have little wind loading and an SWR of better than 2:1 on 1.6 to 18 MHz, and 3:1 above 18 MHz. Yaesu YA-30 specifications: * Frequency Range: 1.6-30 MHz * Input Impedance: 50 Ohms * Power Input: 150W PEP (voice) for 3-30MHz * Power Input: 75W (AM, FM, Data, RTTY) TX five minutes maximum 20 percent duty cycle * Input Connector: UHF-type socket * Antenna Length: 83 ft. * 55 ft. inverted "V" configuration (with a 35 ft. tower) Special features: * No Tuner required * UV resistant spacer rods * UV resistant balun * Stainless steel wire * Supplied with 100 ft. of coaxial cable You've heard of the renowned Yaesu quality. If you would like a broadband antenna for 160 through 10 that will last the test of time, then look at one of these Yaesu YA-30 Broadband HF Folded Dipole Antennas from DX Engineering!
( 2 )
$349.99