Availability
19 Results Found For "Choke"
Momobeam RFC-DU 5kW RF Choke Baluns
Momobeam RFC-DU 5kW RF Choke Baluns provide an excellent balance of currents and ensure a proper transition between balanced resonant antenna systems (with low SWR)—such as dipoles and Yagi antennas—and unbalanced coaxial feedlines. These RF Chokes are highly effective at suppressing common mode current from flowing along the exterior of coaxial feedlines, a condition that can cause several issues, including: - Increased noise levels - Inaccurate SWR meter readings - Interference affecting electronic devices within our shack or near the antenna system
Not Yet Reviewed
$265.99
Momobeam RFC-DU 10kW RF Choke Baluns
Momobeam RFC DU 10kW RF Choke Baluns provide an excellent balance of currents and ensure a proper transition between balanced resonant antenna systems (with low SWR)—such as dipoles and Yagi antennas—and unbalanced coaxial feedlines. These RF Current Chokes are highly effective at suppressing common mode current from flowing along the exterior of coaxial feedlines, a condition that can cause several issues, including:
Not Yet Reviewed
$361.99
Momobeam RFC-TC-5kW RF Choke Baluns
Momobeam RFC-TC-5kW RF Choke Baluns are broadband common-mode current (CMC) chokes designed for operation from 3 to 50 MHz. They provide current balance between balanced resonant antennas and unbalanced coaxial feed lines, helping prevent common-mode current from flowing on the outside of the coaxial cable. Applications include 50-Ohm Yagi antennas, resonant dipoles, and replacement of damaged 1:1 current baluns or RF chokes. The RFC-TC-5kW RF choke balun is constructed using high-quality Teflon-insulated coaxial cable wound on three 2.4-inch toroidal cores and housed in a UV-resistant IP65-rated enclosure. Key Features • Function: Suppresses common-mode current (CMC) on coaxial feed lines • Noise Reduction: Helps reduce received noise levels • SWR Accuracy: Helps prevent incorrect SWR meter readings • Interference Mitigation: Helps reduce RF interference to nearby electronic devices • Recommended Applications: 50-Ohm Yagi antennas, resonant dipoles, and replacement of damaged 1:1 baluns or RF chokes Additional Features & Specifications: • Frequency Range: 3-50 MHz • Impedance Ratio: 50 Ω (1:1) • Common-Mode Rejection: 30 to 50 dB • Maximum Applicable Power: 5 kW PEP (50 Ω resonant load, SWR 1:1) • Core Configuration: Triple 2.4 in toroidal cores • Cable Type: High-quality Teflon-insulated coaxial cable • Enclosure Material: UV-resistant ABS • Environmental Rating: IP65 • Connector Configuration: 1 × SO-239, 2 × stainless-steel threaded terminals • Weight: 2.0 lbs. (0.9kg) excluding packaging • Manual Language: English
Not Yet Reviewed
$255.99
Momobeam RFC-PC 6kW RF Choke Baluns
Momobeam RFC-PC 6kW RF Choke Baluns are efficient broadband common mode current chokes designed to ensure proper current balance and clean transitions between balanced resonant antennas—such as dipoles and Yagi antennas—and unbalanced coaxial feed lines. By delivering excellent suppression of unwanted common mode current across a wide frequency range, these RF chokes help maintain optimal antenna performance and protect sensitive station equipment. Common mode currents can cause a variety of station problems, including elevated receiver noise levels, inaccurate SWR measurements, and interference affecting nearby electronic devices or equipment within the shack. The RFC-PC 6kW effectively prevents these issues by stopping common mode current from traveling on the outside of the coaxial shield, ensuring cleaner transmit and receive performance under all operating conditions. Thanks to its broadband characteristics, the RFC-PC 6kW can be used with virtually any 50 ohm feed antenna system. It is ideal for Yagi antennas, resonant dipoles, and any installation where clean feedline behavior is essential. The choke also serves as an excellent replacement for damaged or aging 1:1 RF chokes or baluns, offering improved suppression and modern build quality. With robust performance, wide compatibility, and reliable common mode current elimination, the Momobeam RFC-PC 6kW RF Choke Baluns provides a simple yet essential upgrade for ensuring your antenna system operates at its best.
Not Yet Reviewed
$434.99
Momobeam RFC-LI-5kW-TC Line Isolator RF Current Baluns
Momobeam RFC-LI-5kW-TC Line Isolator RF Current Baluns are a broadband 1:1 line isolator and common-mode current (CMC) choke designed for operation from 3 to 50 MHz. Installed directly in a 50 Ω coaxial feed line, it suppresses common-mode current on the outside of the coax shield and helps maintain proper current balance between balanced antennas and unbalanced feed systems. The line isolator can be installed at the antenna feed point, at the base of a tower, near the radio station, or along feed lines used with End Fed antennas. Construction consists of high-quality Teflon-insulated coaxial cable wound on three 2.4-inch toroidal cores and housed in a UV-resistant IP65-rated ABS enclosure. Benefits: • Function: Suppresses common-mode current on coaxial feed lines • Installation Locations: Antenna feed point, tower base, near the shack, or inline with the feed system • Feedline Application: Suitable for use as a feedline choke on coaxial cable runs • End Fed Compatibility: Can be used with End Fed antenna feed lines • Noise Reduction: Helps reduce receiver noise caused by feedline current • SWR Accuracy: Helps prevent inaccurate SWR meter readings • Interference Mitigation: Helps reduce RF interference to nearby electronic equipment • Construction: Triple-core design using Teflon-insulated coaxial cable wound on 2.4-inch toroidal cores Additional Features & Specifications: • Frequency Range: 3-50 MHz • Impedance Ratio: 50-Ohm to 50-Ohm (1:1) • Common-Mode Rejection: 30 to 50 dB • Maximum Applicable Power: 5 kW PEP (50 Ω resonant load, SWR 1:1) • Core Configuration: Triple 2.4 in toroidal cores • Cable Type: High-quality Teflon-insulated coaxial cable • Enclosure Material: UV-resistant ABS • Environmental Rating: IP65 • Connector Configuration: (2) UHF SO-239 female • Weight: 2.0 lbs. (0.9kg) excluding packaging • Manual Language: English
Not Yet Reviewed
$255.99
CG Antennas BL-49 Unun
CG Antennas BL-49 Unun, also referred to as a 49:1 Balun, is an outdoor HF antenna feedpoint transformer. This high ratio device is particularly suitable for building an End Fed Half Wave, or EFHW antenna. Available as part number CGA-11365-49 from DX Engineering, this 49:1 Unun is built with heavy gauge wire and a large toroidal ferrite core which handles up to 600W PEP over the entire range from 1.8 to 30 MHz. The waterproof case is high strength plastic with a special valve to drain off unavoidable condensation while preventing insects from entering and nesting. A stainless steel eye hook at the top of the Unun provides an attachment point for a support rope to handle the weight of the Unun, antenna wire, and coax. Also on top is a stainless steel stud and wing nut for the antenna wire and another is on the bottom, next to a SO-239, for an optional counterpoise wire or ground connection. End-fed half-wave antennas (EFHW) are very popular because they are easy to hang in limited space installations while achieving multi-band functionality with a transceiver built-in tuner or an external wide range tuner. In many cases the use of a BL-49 Unun with a specific monoband wire length can achieve low or reasonable SWR on many harmonically related Amateur bands. The radiation pattern of an EFHW antenna is similar to that of a dipole and the 49:1 Unun adapts to different end-fed wire configurations; the antenna wire may be suspended straight and parallel to the ground, or angled as an inverted-V or inverted-L, or run diagonally as a sloper wire, with the BL-49 Unun feedpoint located anywhere from a few feet above the ground hanging high from a support. Experimentation is encouraged with this very adaptable and forgiving feedpoint method, where the position of the wire in relation to the ground or any metal having the greatest effect on the efficiency and the pattern of the EFHW wire antenna. See antenna texts and web forums for wire lengths known to provide the best results, such as 60-70 ft. for 80-10 meters. CG Antennas BL-49 Unun Specifications: Frequency Range: 1.8 - 30 MHz, antenna tuner required. Transformer Ratio: 49:1 Feedline Impedance (Ω): 50 Ohm Max. Power: 600W SSB Connector: SO-239 – UHF female Size (WHD): 3.582 x 5.984 x 2.165 in. (91 x 152 x 55 mm) Weight : 1.15 lbs. (520 g)
( 1 )
$335.99
Momobeam Mono3-10 Three Element 10M Yagi Antennas
Momobeam Mono3-10 Three Element 10M Yagi Antennas are engineered using the latest generation design software to deliver exceptional performance across the entire 10 meter band. With full size elements and precision optimized geometry, these antennas are ideal for operators who want maximum efficiency, gain, and on air reliability without compromise. Built on a robust square boom, the MONO3 10 is designed for easy, accurate assembly. Each system includes an assembly tool, spare hardware (bolts and aluminum tubing), and fully labeled components. All hardware is packaged in clearly marked bags, and every aluminum tube is labeled to ensure a fast, frustration free installation experience. These antennas are suitable for both mast mounting and side mount tower configurations, offering excellent flexibility for station design. A medium duty rotor is required for proper operation. To further enhance performance and reduce feedline issues, every MONO3 10 comes standard with a 3 kW RF choke balun—a premium component that many manufacturers offer only as an upgrade. Momobeam RF Chokes are constructed from high quality, low loss, double shielded coaxial cable with a Teflon dielectric, combined with carefully selected ferrite material sleeved over the cable to create a high impedance path for RF, providing excellent isolation between the antenna and the coaxial feedline. Mono3-10 Features and Specifications: RF Choke Balun: 3kW included Band Coverage: 10-meters Frequency Range: 27 – 28.8 MHz Bandwidth@ S.W.R. ≤ 1.5:1: 1800 kHz Longest element: 9.4 ft. (287cm) Power Handling: 10kW Wind Area: 2.7 sq. ft. (0.25m²) Wind Load: (80 MPH): (500N) 112.4 lbf. Wind Survival*: 100 Mph (160 Km/h) Tower Leg/Mast Diameter: 2.0-2.36in. (50/60mm) Tower Lift Side: 1.25ft. (40cm) above the tower top Weight: 22 lbs. (10kg) Feedline Connector: (1) 50-Ohm UHF SO-239 female Tubes and Plates: Aluminum alloy 6061T6 Hardware: Stainless steel Insulating Clamps: Polypropylene, UV resistant
Not Yet Reviewed
$437.99
DX Engineering ISO-PLUS Ethernet RF Filters
DX Engineering ISO-PLUS Ethernet RF Filters are very effective EMI Suppressors that are quickly and easily connected inline on Cat5e or Cat6 network cables. Their patented* design provides common mode RF interference and EMI noise filtering of radio frequencies from well below 1 MHz to 100 MHz and beyond. DX Engineering ISO-PLUS Ethernet RF Filters have no effect on throughput; Ethernet data signal levels and speed remain unchanged. *US Patent No. 11,211,679 B2 Electromagnetic interference (EMI), also known as RF interference (RFI), can be imposed onto your received radio and data signals from many electronic devices normally found around a residence, a radio room or a business network. Areas of major concern are the Gigabit Ethernet Cat5(e) and Cat6 cables used for network (LAN) connections between personal computers, printers, multi-port switches, cable modems, routers and radio transceivers, and between many other devices. DX Engineering ISO-PLUS RF filters, installed on both ends of Ethernet cables, work two ways. First, they can mitigate RF interference caused to the Ethernet connected device. Second, they can reduce interference to radio receivers and other Ethernet devices that is caused by RFI or EMI generated by an Ethernet connected device. ISO-PLUS filters are sold in pairs and are normally installed at each end of an Ethernet cable; one filter at the RJ-45 Ethernet plug of the first device and the other filter at the RJ-45 Ethernet plug of the second device. Each ISO-Plus comes with one six inch shielded RJ-45 patch cable (color may vary). They are designed to be installed in pairs; offered in a 2 filter package DXE-ISO-PLUS-2 or a 10 filter package DXE-ISO-PLUS-10. Click "More Details" below for additional information. DX Engineering ISO-PLUS Ethernet RF Filters are an important tool to improve productivity and radio reception of weak signals. "If you can't hear them, you can't work them." Order ISO-PLUS Ethernet RF Filters exclusively from DXEngineering.com
( 49 )
$355.99
Momobeam Mono4-6 Monoband Yagi Antennas
Momobeam Mono4 6 Monoband Yagi Antennas are purpose built for the 6-meter magic band of 50MHz and optimized for DX operators who demand high performance in a lightweight, field ready design—perfect for SOTA, POTA, and other portable VHF activities. Weighing only 8.82lbs., these antennas deliver impressive gain, strong front to back performance, and a remarkably flat SWR curve of less than 1.5:1 across the entire 6 meter band. Despite their compact profile, they provide the reliable on air results expected from a full featured Yagi. Assembly is simple and intuitive. Built on a durable round boom, each antenna includes all hardware packed in clearly labeled bags, and every aluminum tube is individually marked to ensure a quick and effortless setup—whether in the field or at home. Requiring only a light duty rotator, the Mono4 6 is an excellent choice for portable masts, lightweight towers, or temporary installations where performance and convenience both matter.
Not Yet Reviewed
$327.99
Chameleon Antenna MPAS Lite with Hybrid Mini Modular Antenna Systems
CHAMELEON ANTENNA CHA MPAS Lite is the little brother of the CHA MPAS 2.0. The Modular Portable Antenna System is a concept allowing the radio operator to configure and deploy the antenna system in a variety of configurations. Some of the possible deployment configurations include Vertical, Horizontal, Sloper, Inverted V, Inverted L, NVIS, Balcony, Vehicle (Stationary) and Backpack Portable. The MPAS Lite With Hybrid MINI Antenna System consists of: • 1 X CHA HYBRID-MINI Feedpoint with SO-239 • 1 X 60 ft. Wire • 1 X SS17 (17' long collapsible stainless steel whip) • 1 X CHA SPIKE • 1 X CHA 50 ft. coax with RFI choke • Stainless Steel Hardware Longer antenna wires, counterpoise and carry bag are user supplied. The integral broadband impedance matching network transformer of the CHA HYBRID-MINI allows broadband antenna tuning. These antennas will operate from 1.8 - 54 MHz, continuous, without any adjustment when using a wide-range antenna tuner (the shortest configuration has limited performance below 3.5 MHz). The CHA MPAS Lite With Hybrid MINI Antenna System details: * Frequency Range: 1.8 - 54 MHz (all configurations require a wide-range antenna tuner) * CHA HYBRID MINI with 60 ft. wire and customer-supplied counterpoise: 1.8 MHz through 54 MHz * CHA SS17 TELESCOPIC WHIP: 24-54 MHz (whip only) * CHA HYBRID MINI, all configurations: 250 W (CW, AM, FM, RTTY), 500 W SSB RF Connection: * UHF Female on CHA HYBRID MINI UHF Female SO-239 Use of SS17 WHIP is NOT RECOMMENDED for permanent installations Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 4 )
$385.00
Grazioli Antennas G-Max 10 & 11 Meter 5/8-Wave Collinear Vertical Antennas
Grazioli Antennas G-Max 10 & 11 Meter 5/8-Wave Collinear Vertical Antennas are the world's first and only vertical antennas for the 10 and 11 meter bands to utilize a true 5/8-wave collinear configuration, delivering gain well beyond that of a conventional 1/4-wave design. Built on the proven mechanical platform of the FE10V, the G-Max delivers performance comparable to, and in some cases surpassing, that of a 2-element Yagi while maintaining the key advantage of omnidirectional coverage. The G-Max stands apart from conventional vertical antennas, including 5/8-wave, J-Pole, and other competing designs. Its high gain, compressed radiation pattern, and low-angle radiation characteristics provide outstanding local and DX performance, setting a new benchmark for omnidirectional 10 and 11 meter operation. Materials & Construction: The antenna is constructed from AW6063-T66 aluminum alloy, a high-strength aluminum-magnesium-silicon alloy hardened to the T66 temper. This material provides exceptional durability through an extrusion and cold-drawing process. Precision-manufactured tubing maintains tight tolerances for both diameter and wall thickness, ensuring accurate fitment with minimal play between sections. The ground plane consists of four heavy-duty 8.9-foot full quarter-wave radials built from two telescoping sections secured with clamps. Radial sections measure 0.50 and 0.39 inches in diameter. The radials are attached to the support plate using U-bolts and self-locking nuts, while four fiberglass reinforcements strengthen the mounting points and help prevent tube deformation during installation and operation.\ The Phasing Correction Coil: The G-Max phase coil is strategically positioned between the two central radiating sections and performs three critical functions essential to the antenna's collinear design. First, it introduces a 180° phase shift between the lower 1/4-wave section and the upper 5/8-wave section, ensuring the entire radiating element operates in phase for maximum efficiency. Second, the coil compensates for the significant capacitive reactance present in the upper 5/8-wave section through its inherent inductive reactance. Third, it transfers RF power to the upper radiating section with minimal loss, maintaining efficient energy distribution throughout the antenna. These functions are made possible by the coil's high-Q design, engineered to provide precise phase control, effective reactance compensation, and low-loss power transfer for optimum performance. The Fixing Bracket: The heavy-duty mounting bracket is manufactured from 0.09 in. (2.5 mm) thick AISI 304 stainless steel for excellent strength and corrosion resistance. It attaches to the antenna tube using a clamping system that provides an exceptionally secure mechanical connection. Mast mounting is accomplished with AISI 304 stainless steel M6 V-bolts and high-profile nuts, allowing for easy installation and secure tightening while ensuring long-term durability in outdoor environments. Additional Features & Specifications: - Radiation Type: Omnidirectional - Polarization: Linear Vertical - Gain: 3.5 dBd (5.65 dBi) - Bandwidth (SWR 2:1): ≥ 1.3 MHz @ 27 MHz - SWR at Resonance: ≤ 1.2 typical, < 1.1 - Feed System: Direct feed with DC-ground choke - Input Connector: 50 Ω UHF SO-239 female, PTFE insulator, gold-plated pin - Maximum Input Power: 5,000 watts continuous, all modes - Antenna Height (with mounting tube): 35.60 ft. (10.85m) - Radial Length: 8.90 ft. (2.7m) (full quarter-wave) - Mounting Mast Diameter: 1.57 – 2.12 in. (40-54mm) - Wind Survival (with guy ropes, no ice): 80.78 MPH (130 km/h) - Antenna Net Weight: 15 Lbs. (6.8kg) - Package Dimensions: 5.50 x 5.50 x 57.0 in. (14 × 14 × 145cm) - Shipping Weight: 18.07 lbs.8.2 kg
Not Yet Reviewed
$449.99
Chelegance JPC-7 Portable HF Dipole Antenna
Chelegance JPC-7 Portable HF Dipole Antenna features a very handy set of parts that assemble quickly, to cover 40 through 6 meters. This set includes special antenna base, a 1:1 choke balun with SO-239 and connection leads, hardware, manual tuning multi-band coils, heavy-duty aluminum arms, and stainless telescopic whips. This dipole kit comes packed into the provided 14.5 x 9.0 in. carry bag but extends out to over 21.5 ft. overall. With manually tuned center-mount coils and whip adjustments, this antenna offers very good performance from 7 MHz and up. It handles up to 100 watts and is quickly assembled to mount and connect with a user supplied tripod/mast and coax, for temporary portable use, on the go! Chelegance JPC-7 Portable HF Dipole Antenna parts list: * 1 x Antenna base * 1 x 1:1 Choke balun * 1 x Balun strap * 2 x Telescopic whips 98.4 in. (2.5 m) * 2 x Multi-band coil * 4 x Aluminum arms, 0.75 x 12.6 in. (19 x 320 mm) * 2 x Rotating arm bracket kit * 2 x Brass connector * 1 x Tripod adapter * 1 x Antenna bag 14.5 x 9.0 in. (37 x 23 cm) * 1 x User manual
( 1 )
$374.99
CHAMELON ANTENNA CHA MPAS Lite Modular Portable Antenna Systems
CHAMELON ANTENNA CHA MPAS Lite is the little brother of the CHA MPAS 2.0. The Modular Portable Antenna System is a concept allowing the radio operator to configure and deploy the antenna system in a variety of configurations. Some of the possible deployment configurations include Vertical, Horizontal, Sloper, Inverted V, Inverted L, NVIS, Balcony, Vehicle (Stationary) and Backpack Portable. The MPAS Lite antenna system consists of: • 1 X CHA HYBRID-MICRO Feedpoint with SO-239 • 1 X 60 ft. Wire • 1 X SS17 (17' long collapsible stainless steel whip) • 1 X CHA SPIKE • 1 X CHA 50 ft. coax with RFI choke • Stainless Steel Hardware Longer antenna wires, counterpoise and carry bag are user supplied. The integral broadband impedance matching network transformer of the CHA HYBRID-MICRO allows broadband antenna tuning. These antennas will operate from 1.8 - 54 MHz, continuous, without any adjustment when using a wide range antenna tuner (the shortest configuration has limited performance below 3.5 MHz). Here are the CHA MPAS Lite details: Frequency: (all configurations require a wide range antenna tuner) * CHA HYBRID MICRO with 60 ft. wire and customer supplied counterpoise: 1.8 MHz through 54 MHz * CHA SS17 TELESCOPIC WHIP: 24-54 MHz (whip only) * CHA HYBRID MICRO, all configurations: 50 W (CW, AM, FM, RTTY), 100 W (SSB and SSB-based digital modes) RF Connection: * UHF Female on CHA HYBRID MICRO (SO-239) Use of SS17 WHIP is NOT RECOMMENDED for permanent installations.
( 9 )
$360.00
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles
Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles are compact all aluminum self-supported dipole antennas specifically designed for "Limited-Small space" applications. Designed for use with an antenna tuner, each element is fitted with an M5 stud and wing nut to enable easy feed wire connection. The central bracket has two U bolts to allow attachment to a 50mm (1-7/8 in.) OD mast. Radiating elements are manufactured from telescoping 25mm and 22mm diameter "drawn," not extruded, aluminum tubing. This makes them flexible and extremely resilient to high winds and bird landings. The width of the assembled antenna is only 6.8 meters (22.31 ft.). They are configured to operate in a frequency range of 3-54 MHz with the aid of a manual/auto tuner. Ultimate band coverage is subject to the functional range of your antenna tuner. If not using a remote mast-mounted tuner, then an RF choke or balun should be used at the antenna to limit RFI. Dipole elements are two-piece to reduce the shipping length to 202 centimeters (79.53 in.). These antennas are very easy to assemble and with a weight of only 3 kg (6.6 lbs.) they are extremely easy to erect. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. These antennas are ideal for pairing with an LDG-RT-RC-100 remote autotuner and a Channel Master CNM-9521A light Duty Rotator System. Order Bushcomm Horizon 6.7 Compact Non-Resonant Dipoles and accessories from DX Engineering!
( 5 )
$429.99
InnovAntennas OP-DES 50 MHz Yagi Antennas
InnovAntennas OP-DES 50 MHz Yagi Antennas are a relatively new development from InnovAntennas. OP-DES stands for Opposing Phase Driven Element System, in which the ends of the dipole radiator of these antennas is angled backwards towards the reflector, parallel to the boom. This results in opposing phase relationships in the ends of the driven element, providing a very clean directional pattern with few side lobes. The OP-DES Yagi has optimized gain over a wide frequency range, while retaining a good front-to-back ratio. The driven element dipole of an OP-DES antenna has a low impedance of 50 ohms. This eliminates the need for matching elements or a transformer balun. For this reason, the antenna is offered without a balun, but an RF choke balun made of ferrites on coax should be used at the feedpoint terminal studs. With the coaxial cable directly connected to the driven element dipole, well over full legal limit power levels are possible. Like all InnovAntennas Yagis, the OP-DES 50MHz antennas are extremely robustly constructed; the larger model uses truss cables for the boom. All elements of the antenna use high quality aluminum, the clamps and screws are made of stainless steel. The supplied mast clamp is designed for masts up to 2 in. (50mm) diameter. Application Description Monoband Yagis are often used at contest stations, or when you want to use only one band for a certain time, for example to focus on a specific target during sunspot minimum. Another advantage of monoband antennas are the stacking possibilities, i.e. the arrangement of two or more identical antennas properly spaced from each other. InnovAntennas Yagis provide all the necessary technical specifications, so there is no guesswork about the stack spacing. The InnovAntennas OP-DES 50 MHz Yagis are designed through careful numerical optimizations to provide excellent gain with good bandwidth. As a result, a low SWR of 1.1:1 is achieved in the frequency range of 50.0 - 50.6 MHz (6-element) or 50.0 - 51.35 MHz (5-element). The experience of the developer Justin, G0KSC ensure superior operations with these antennas in practice, often supported by a lively exchange between users. TECHNICAL DATA InnovAntennas OP-DES 50 MHz Yagi (Monoband) Antenna Mast Mount: Center Antenna Type Directional Antenna Band 6m Power Handling: 5000 W Polarization: Horizontal Balun Included: No Mast Diameter Max.: 2.00 in. (50mm)
( 2 )
$389.99
DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies
What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849
( 8 )
$250.40
—
$499.20
InnovAntennas VertiGO HF Vertical Antennas
InnovAntennas VertiGO HF Vertical Antennas cover multiple bands when fed as a non-resonant radiator using a remote antenna tuner mounted at the base. They can also be fed directly as a monoband vertical and are typically and most easily installed as a ground-mounted vertical, depending on the location and the support. To achieve the matching required by modern transceivers and amplifiers, other shortened vertical radiators use traps or coils but, those components contribute to losses; power lost as heat. InnovAntennas VertiGO Antennas radiate on all bands along their entire length. Radials are required for efficient operation of any HF vertical; 16 or more ground radials are better, where their length isn't critical. A remote tuner installed at the base of the antenna provides maximum efficiency and the best performance on the bands indicated. Higher frequencies will tune but higher angle patterns will limit performance. A ferrite bead choke should be used at the remote tuner on the coaxial cable from the station to prevent it from radiating and collecting RF noise. VertiGO Vertical Antennas from InnovAntennas are available in three different height versions, each with rugged aluminum tubing sections, swaged and slit at the top for the element clamps. Brackets and clamps are included for mounting to a user supplied support pipe.
( 1 )
$399.99
—
$475.99
Grazioli Antennas MV3 HF Tri-Band 20/15/10M Vertical Ground Plane Antennas
The Grazioli Antennas MV3 is a base-fed 1/4-wave tri-band vertical ground plane antenna designed for operation on the 20, 15, and 10-meter Amateur Radio bands. Engineered to provide an excellent balance of performance, durability, and low visual impact, the MV3 is an ideal solution for operators seeking a compact multiband antenna without sacrificing efficiency. Standing 18.5 ft (5.63 m) tall and weighing just 11.0 lb (5 kg), the MV3 is lightweight yet rugged, making it suitable for a wide range of installations while typically requiring no guying under normal conditions. Constructed from premium AW6063-T66 aluminum alloy tubing, precision CNC-machined aluminum components, and high-quality AISI 304 and AISI 316 stainless steel hardware, the MV3 is built to provide years of dependable service in demanding outdoor environments. The antenna is rated for up to 3 kW continuous power in all operating modes and includes a detailed assembly manual along with a unique serial number identifying the production batch and manufacturing data for quality traceability. Note: For installations in areas subject to exceptionally high winds, the use of non-conductive guy ropes is recommended for additional mechanical support. High-Performance Tri-Band Design The MV3 is a resonant vertical antenna designed specifically for operation on the 20, 15, and 10-meter amateur bands. Its direct-feed design eliminates the need for impedance transformers or matching devices that could introduce losses or limit power-handling capability. By utilizing a resonant feed system, the antenna maintains efficient RF power transfer while supporting its full 3 kW continuous power rating. The antenna incorporates a high-impedance inductive network that creates a DC-grounded condition, helping to dissipate atmospheric electrical disturbances and electrostatic charges that may accumulate on the antenna structure. DBFC Counterpoise System The MV3 incorporates Grazioli's DBFC (Dual Band Folded Counterpoise) system, a unique counterpoise design that enhances operation across all supported bands while maintaining a compact installation footprint. The system utilizes four aluminum radial elements measuring 7.9 ft (2.4 m) each, along with an additional radial constructed from AISI 316 stainless steel cable. This arrangement eliminates the need for loaded radial systems or long wire radials spread across a roof or property. The DBFC design assists with maintaining proper antenna operation even in installations located near the ground or on rooftop structures while preserving efficiency and simplifying installation. FAIR-RITE RF Choke System The MV3 is supplied with an original FAIR-RITE FT240-43 ferrite toroid, manufactured in the USA, for construction of a high-performance RF choke. When installed directly below the antenna feed point, the choke significantly attenuates common-mode currents within the HF spectrum from 1.8 to 30 MHz. This helps maximize antenna performance while reducing unwanted RF current on the feed line. Proprietary High-Power UHF Connector Rather than utilizing a conventional commercial SO-239 connector, the MV3 features a proprietary connector designed and manufactured by Grazioli. The connector provides a true 50-ohm characteristic impedance and is rated for operation up to 500 MHz. Heavy-Duty Mounting System The MV3 mounting bracket is fabricated from 0.098 in (2.5 mm) thick AISI 304 stainless steel and secures to the antenna through a robust clamping system that provides exceptional mechanical strength. Mast attachment is accomplished using an AISI 304 stainless steel M6 V-bolt and column-nut assembly, ensuring a secure installation and long-term reliability in outdoor operating environments.
Not Yet Reviewed
$469.99
InnovAntennas 144 MHz OWL Ultra Yagi Antennas
InnovAntennas 144 MHz OWL Ultra Yagi Antennas offer the 2 meter weak-signal enthusiast undeniable low-noise performance with amazing SWR bandwidth, particularly good gain and an excellent front-to-back ratio. Five Optimized Wideband Low-impedance (OWL) Ultra Yagi antennas are available, starting with six element up through ten element models. InnovAntennas' OWL Ultra Yagi beams have been extensively numerically simulated and optimized using special software that includes a 3D simulation of the boom, the insulators, the connector and the cable; an elaborate numerical simulation of these antennas that was inconceivable a decade before. InnovAntenna has achieved the best of what is technically possible for a wideband 2 meter Yagi. The boom of the 144 MHz OWL Ultra Yagi is 1 in. (25mm) square aluminum featuring through-the-boom insulated elements. The adjustable center fed folded dipole has the side opposite the 50 ohm feedpoint connected to the boom, which removes static charge to protect the transceiver. This antenna acts like a band-pass and noise filter outside the 2 meter band, due to rapidly rising impedance. However, the most important feature of OWL Ultra Yagi antenna is optimization for reduced side lobe in the elevation plane, achieving dramatically reduced received noise, even in high ambient noise city locations. The InnovAntennas OWL Ultra Yagis are suitable for all "weak signal modes" on the low end of the 2 meter band due to the optimization for high gain with incredibly low noise for EME, Meteor Scatter, Tropo-DX, Sporadic-E, etc. Despite the robust construction (the antennas can withstand wind speeds of up to 100 mph (160 km/h), the Yagis are still relatively light and thus suitable for smaller masts or for stacking several antennas. The OWL Ultra Yagis do not include a balun, as the coaxial cable connects directly to the loop driven element dipole. The antenna can handle 5 kW, but the recommended choke balun handles a maximum power of approx. 1.0 to 1.5 kW is possible. Exceptionally good SWR is achieved over a wide frequency range. With excellent gain to noise ratios (G/T ratio), the economical InnovAntennas OWL Ultra Yagis are well suited for use in stacked arrays, for EME, satellite or terrestrial operations. Each model listing describes the key benefits of the OWL Ultra Yagi Antennas. Your antenna is a part of your receiver and arguably the most important part of your station. You have spent thousands on radio equipment; make sure you don't short-change your set-up by choosing anything other than an InnovAntennas OWL Ultra Yagi.
Not Yet Reviewed
$274.99
—
$469.99