Availability
12 Results Found For "anchor"
Amerite Anchor Bases
Some hams like to look for options when doing concrete tower bases. American Tower Company Amerite Anchor Bases give you another option: Instead of burying part of a tower section in concrete, you may find that using a tower-anchor base cage better suits your needs. These anchors are available for Amerite 25 and 45 Series towers. Included with the AME-25-ABC: Three 1/2 by 3 by 6 in. bar with three 1-1/4 in. diameter tower stubs Three 3/4 by 3/4 by 1/8 in. angle brackets Six 1/2 by 18 in. "J" bolts with nuts Included with the AME-45-ABC Three 1/2 by 3 by 6 in. bar with three 1-1/4 in. diameter tower stubs Three 3/4 by 3/4 by 1/8 in. angle brackets Six 3/4 by 18 in. "J" bolts with nuts Once assembled, these anchor bases may be embedded in concrete to provide a fixed base for your tower. Order your American Tower Company Amerite Anchor Bases from DX Engineering!
Not Yet Reviewed
$268.99
—
$315.99
ROHN Guy Anchor Rods
ROHN Guy Anchor Rods allow for the attachment of up to five levels of guy wires. Some models are provided with a top plate for guy wire attachment and are designed to be installed in a concrete base. All are galvanized for extended service.
( 3 )
$279.99
Universal Towers Tower Base Anchors
Universal Towers Tower Base Anchors are designed for use with Universal Towers towers. Ensure correct fitment by choosing your corresponding tower section. Universal Towers tower bases are constructed from high-quality materials and engineered for high strength and durability. Give your tower a proper foundation with Universal Towers Tower Base Anchors from DX Engineering.
Not Yet Reviewed
$270.75
—
$429.40
ROHN Tower Base Bolts
ROHN Tower Base Bolts are galvanized steel bolts that are set into the concrete base pier when it is poured. These bolts anchor ROHN Tower Concrete Base Plates and Hinged Base Plates to the concrete pier.
( 4 )
$499.99
TBX Tower Base Stubs
TBX Tower Base Stubs facilitate mounting the bottom of the tower to the concrete tower base. These are literally stubbed tower-leg sections that are 4 ft. in length. Each base stub number corresponds to the tower section that the stubs fit. That means that a TBX-BS-3 will fit the TBX-3 tower section. The TBX-BS-7/8 will fit both the TBX-7 and TBX-8 tower sections. Use these base stubs to anchor your TBX Tower when NOT using a tilt-base. For tilt-base applications, use the recommended anchor bolts. TBX Towers are deluxe steel towers that won't break the bank! When you want to anchor one of your own TBX towers, contact DX Engineering for some TBX Tower Base Stubs!
Not Yet Reviewed
$280.00
ROHN 25G/45G-Series Guy Anchor Grounding Kits
ROHN 25G/45G-Series Guy Anchor Grounding Kits are so important that they are included in each ROHN 25G and 45G complete tower package. However, when purchased from ROHN separately, this part number includes only the 30 ft. of 7/16 in. ground wire, three 10 ft. copper-clad 5/8 in. ground rods and three 3/4 in. ground rod clamps. The required R-CPC.5/.75 anchor rod clamps (three) that connect to the actual Guy Anchor Rod (and are needed to complete the grounding installation) are sold separately. Also, as these kits contain items 10 ft. in length, they can only ship truck freight. Tower grounding is the single most important effort in protecting your shack from lightning. Order these ROHN 25G/45G-Series Guy Anchor Grounding Kits from DX Engineering and improve your tower grounds.
Not Yet Reviewed
$399.99
ROHN Self-Supporting Concrete Base Plates
ROHN self-supporting tower base plates ensure the proper installation of your ROHN 25G or45G series tower when anchored to a concrete base with 5/8 x 12.0 in. bolts. ROHN concrete base plates are made from durable, 1/2 in. thick galvanized steel.
( 1 )
$349.99
ROHN 55G Tower Short Bases
ROHN SB55G Tower Short Bases are designed to be embedded directly into concrete as the base section for a 55G tower installation. They are positioned in the ground and then have concrete poured around them to provide an anchored connection to the 55G main tower sections. The SB55G short bases use double-bolted joints, which are time-proven to be the best method of joining tower sections of this size for sturdiness and dependability. The ROHN SB55G short bases feature the 55G equilateral triangular design, and are constructed of extra heavy-duty steel tubing legs with a continuous solid-steel rod used in ROHN's signature Zig-Zag bracing. For heavy-duty service and solidly anchored towers, turn to DX Engineering for your ROHN SB55G Tower Short Bases!
( 1 )
$297.99
DX Engineering Tinned Copper Radial Wire Kits
DX Engineering Tinned Copper Radial Wire Kits include plentiful quantities of biodegradable staples and tinned crimp ring terminals that are easily soldered. Along with spools of the same wire as used by the most successful contest stations and DX enthusiasts for their ground-mounted vertical antennas, these kits will help your antenna system achieve optimal performance. The 16 AWG tinned solid copper wire in these kits provide an extremely cost effective solution for the high-count, full-size ground radial wire systems that are required for top-performing HF vertical antenna installations. Ground wire radials do not need to be any specific length because the earth detunes them. Fill your ground-mounted vertical space with radials that run out from the antenna feedpoint in all possible directions, as far as they can go, up to about one-quarter wavelength on the lowest frequency. Even radials that are all about one-eighth wavelength long on the lowest frequency band are just fine for multi-band verticals over reasonably conductive soils. Use longer radials on lossy soils with sand and rocks. In most cases, a greater number of short ground radials will provide greater efficiency and stronger signals than is achieved with a few long radials. DX Engineering Tinned Copper Radial Wire Kits are available in four sizes: Shorter spool kits, 500 ft. and 1,000 ft., are perfect for the single HF ground-mounted vertical. Longer spool kits, 2,500 ft. and 5,000 ft., are intended for 2-element Dual Vertical Arrays, 3-element ProStack Arrays, and 4-element Four Square Array Systems. Each kit has the appropriate number of biodegradable staples and tinned crimp ring terminals. Why is this wire the absolute best choice for any ground-mounted vertical antenna? Because, DX Engineering Tinned Copper Radial Wire will last much longer in a variety of soil conditions as compared to bare copper, copper coated steel or aluminum wires. Radials deployed with those other wire types actually corrode and degrade rather quickly. Unfortunately, they do so slowly enough that the operator does not easily perceive that degradation in terms of antenna system performance. With Tinned Copper wire, full radial system integrity is maintained for a greater number of years. Depending upon soil type, installations with DXE-TCRW16 will maintain vertical antenna performance for many, many years… and even decades. NOTE: To prevent accelerated corrosion and the possibility of noise, DO NOT use metal anchor pins (lawn staples) on Tinned Copper Radial Wire. These kits contain only the DXE-STPL-100BD Biodegradable Anchor Pins to hold down bare wire radials. Biodegradable staples allow easy installation of radial wires and will disperse in a couple years, after they are no longer needed, making them site friendly. Biodegradable staples work best in soft ground where they may be pushed or lightly tapped into the ground. Since they are a lacto-resin material they are subject to breaking in rocky or hard soil and are not intended to be hammered. DX Engineering Tinned Copper Radial Wire kits are the right choice for long lasting top-performance radial systems for your ground-mounted vertical antenna system.
( 2 )
$315.91
Vibroplex Double Keys
If you have been looking for the ultimate double key, then look no further than Vibroplex double keys! Never before in the Vibroplex company history have they offered a double key in their line. A massive steel base anchors the double key in the operating position, while bright chrome top parts and precision movements provide smooth operating. Each model has the famous brass logo plate, with a unique serial number pinned on the top of each base with stainless steel pins. The double keys are available in standard, deluxe, and 24K gold finishes. The deluxe and 24K gold double keys feature jeweled movements. A cord is not included.
Not Yet Reviewed
$399.95
—
$445.95
ROHN Flat Roof Mounts
ROHN Flat Roof Mounts bolt directly to your flat roof surface to support a guyed ROHN 25G or 45G tower. The flat roof location must be water-tight and reinforced to support tower/antenna weight. These bases require the tower to be guyed or bracketed and cannot be used as a self-supporting base plate. These tower bases use double-bolted attachment joints, which are proven to be the best method of joining tower sections for sturdiness and dependability. The associated tower can be used in guyed or bracketed configurations. Roof mounted tower options may limit potential height considerably by restricted guy line lengths and anchoring options. To mount your ROHN 25G or 45G Series tower to a flat roof, use one of these ROHN Flat Roof Mounts from DX Engineering.
Not Yet Reviewed
$379.99
Vibroplex Straight Keys
Vibroplex straight keys are a first for Vibroplex in its 100+ year history. Their design is distinctly Vibroplex. Their heavy, solid-steel base anchors the straight keys to the operating position, while their lever arm pivots in the famous chromed mainframe. An adjustable stainless steel spring allows for complete control of the tension. And, of course, the straight keys have the famous brass Vibroplex logo plate with a unique serial number pinned to the top of the base with stainless steel pins. They are available in standard, deluxe, and 24K gold finishes. Vibroplex straight keys have unique mechanical action, unlike any other straight keys that have ever been manufactured. Their smooth action and heavy steel base allow the operator to send perfect code.
( 23 )
$322.95