Selected Filters


Availability


10 Results Found For "75 ohm coax"

Part Groups

Results 1 - 10 of 10

DX Engineering RG-6/U 75-ohm Quad-Shield Coax Cable Assemblies

Our new DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies are constructed from our own premium DX Engineering brand RG-6/U 75 ohm cable and superior quality weather-sealed nickel-plated compression F connectors. Their best-in-class design reduces loss and provides greater protection against electromagnetic interference. Available in specific lengths between 3 ft. and 200 ft., these pre-assembled cables with F connectors are your most convenient ultra-high quality RG-6/U cable solution. These RG-6/U cable assemblies are ideal for many applications such as active or passive HF Amateur Radio receive antenna systems, magnetic loop antennas, Beverage antennas, over the air TV reception, FM broadcast reception, CATV systems, raw video distribution and satellite radio installations like Sirius/XM. In fact, their low-loss characteristics are excellent up to the microwave frequencies that Satellite Radio systems employ! Our RG-6/U cable assemblies have gas-injected polyethylene foam dielectric for flexibility and moisture resistance. Their 18 AWG center conductor is copper-clad steel and is durable in the extreme. They have two foil shields plus two high-density aluminum braids for ultimate four-layer RF shielding. Their UV protected black exterior jacket is tough PVC (polyvinyl chloride). DX Engineering RG-6/U cable impedance is 75 ohms with an 83 percent velocity factor and have a minimum bend radius of 2.50 in. This is absolutely the best RG-6/U cable available and it's RoHS compliant! Look at these attenuation figures per 100 ft.: 5 MHz: 0.6 dB 30 MHz: 1.1 dB 55 MHz: 1.6 dB Are you installing or upgrading any receiving antenna or video distribution system that uses RG-6/U cable? If so, then these exceptional DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies will make your installation easier and your results so much better!

5.0 out of 5 stars ( 13 )

$64.99

—

$86.99

DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our premium flexible DXE-8X coaxial cable were designed to make the new DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8X cable assemblies available for HF applications. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket, good for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. DX Engineering RG-8X PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These new, ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849

4.96 out of 5 stars ( 545 )

$78.99

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259s, and select lengths with BNC connectors for POTA and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color delivered can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

4.96 out of 5 stars ( 23 )

$99.99

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies feature different silver plated connectors at each end – high quality BNC and PL-259s PTFE dielectric connectors – especially useful for POTA activations and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. The actual jacket color delivered can vary. DXE-8XV is the part number for this coaxial cable sold by the foot and is also available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 1 )

$99.99

DX Engineering RG-8X 50-ohm Coaxial Cable Adapter Assemblies

DX Engineering RG-8X 50-ohm Coaxial Cable Adapter Assemblies feature different silver plated connectors at each end – high quality BNC and PL-259s PTFE dielectric connectors – especially useful for POTA activations and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering cable assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. DX Engineering RG-8X 50-ohm Coaxial Cable Assemblies are the most flexible, lowest loss and highest quality coaxial cable assemblies on the market. DXE-8X cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8X cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. DX Engineering DXE-8X is the industry standard specifications black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8X is the part number for this coaxial cable sold by the foot and it is also available in 1,000 ft. spools as DXE-8X-1000. DXE-8X Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 1 )

$89.99

DX Engineering RG6 Type-F Compression Connector Tools

DX Engineering RG6 Type-F Compression Connector Tools are designed to install all modern watertight Type-F compression connectors. These ratchet compression tools install all Type-F compression connectors onto all types of RG6 properly. Installing Type-F compression connectors? Do the job right with DX Engineering RG6 Type-F Compression Connector Tools.

5.0 out of 5 stars ( 3 )

$53.99

DX Engineering Receive Feedline Transformers

DX Engineering Receive Feedline Transformers are designed to match your receive antenna 75 ohm output impedance to the nominal 50 ohm input impedance of most receivers. These transformers may be used in almost any receiving application that requires a 75 ohm Type F connection to a 50 ohm BNC connector. These transformers have very low loss (<0.3 dB) and very wide bandwidth, 100 kHz to 30 MHz! Matching the receive antenna or array to the receiver ensures the best possible performance as a result of a system impedance match. *Important! - These Feedline Transformers are Intended to be used on an RF ONLY coax and should NOT be used for power.

5.0 out of 5 stars ( 1 )

$55.99

DX Engineering Pretuned Quarter-Wave Phased Array Cables

DX Engineering Pretuned Quarter-Wave Phased Array Cables are ready to go into your phased array for 80 or 40 meters. These RG-11U coaxial cable assemblies are electronically tuned during production to 3650 kHz and 7100 kHz, the two most popular phased array frequencies. Pretuned Quarter-Wave Phased Array Cables ensure optimum pattern control and gain from your phased antenna array. They are available individually, in pairs and in four-packs, all terminated with soldered silver-plated PL-259s. These cable assemblies are exactly as required for many 80 and 40 meters phased arrays including Comtek Hybrid Four Square Arrays, DX Engineering TFS4 Four Square Arrays, as well as DX Engineering Dual Vertical Arrays. DX Engineering Pretuned Quarter-Wave Phased Array Cables are made from the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable. They are called "phasing feed-lines" because they are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. This RG-11U coaxial cable is manufactured to DX Engineering specifications, with a nominal velocity factor of 0.82. That means they're the right physical length to allow for easy burial and routing from the center-mounted array phasing unit to the base of each vertical element. Maximum performance is achieve with properly installed phased arrays, including ground-mounted base-fed full-size quarter-wave elements with free-space array dimensions and complete, interconnected ground radial wire systems. The electrical dimensions of phased array transmission cables are critical to system performance. Each of our cable assemblies is hand crafted and electronically tuned at DX Engineering. Eliminate the trouble and concern of trying to tune your own cables and order a set of DX Engineering Pretuned Quarter-Wave Phased Array Cables. NOTE: Custom tuned phased cables for all other frequencies in each Amateur band are also available. See DX Engineering Phased Array Quarter Wave Tuned Cables.

5.0 out of 5 stars ( 1 )

$79.99

DX Engineering Receive Feedline Voltage Injectors

DX Engineering Feedline Voltage Injectors, DXE-FVI-1, are high-quality bias-tee devices that place direct current onto a receive antenna system's coaxial cable while preventing DC from reaching the Radio port. These FVI-1 voltage injectors are used to power active accessory devices, such remote relays, switching systems, and preamplifiers. These are the original equipment FVI-1 units provided with single DX Engineering Active Receive Vertical antenna models. Voltage is applied via the 2.1mm power connector to the receive antenna feedline F connector. The RCA phono jack connects to the receiver input with that DC voltage blocked, while passing RF from 100 kHz to 30 MHz. Various RCA phono plug adapters for different RF cable connectors are available in Suggested Parts. Two DXE-FVI-1 feedline voltage injectors may be connected at opposite ends of a feedline to provide DC voltage on the transmission line for your own custom application, keeping the input and output RF devices isolated from the voltage. The included 120V AC 60 Hz wall transformer power supply may be connected to the 2.1mm power connector may to place approximately +12 volts DC on the coaxial cable center conductor, with the coaxial cable shield used as the negative ground return. A different station power supply, 1-16 VDC, may be used with an in-line, 1 Ampere, fast-blow fuse for various devices. DX Engineering feedline voltage injectors are ready for your "DC power on the coax" needs! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you need to inject a DC voltage onto a 75 ohm coaxial cable used for receiving, remember the DX Engineering Feedline Voltage Injector!

Not Yet Reviewed

$99.99

DX Engineering LPFC-BNC Low Power Feedline Chokes

DX Engineering LPFC-BNC Low Power Feedline Chokes are intended to be placed in line with coaxial cable fed antennas and equipment used for portable operations, including POTA and SOTA activations. The DXE-LPFC-BNC coax wound toroid achieves an amazing common mode impedance (CMI) curve, with an RF choking capability that far exceeds the CMI of 'a-few-beads-on-coax' product that is offered by other suppliers. Actually, these "Low Power" Feedline Chokes can be used in any station that runs less than 250 watts SSB, 100 watts CW or Digital. ________________________________________ DX Engineering Low Power Feedline Chokes features and benefits: - A unique, lightweight form, with clear heat shrink over the choke* - Light enough to hang inline at the feedpoint of any portable HF antenna. - BNC female connectors for easy connection to portable antennas and gear. - Much higher CMI that other portable, low power chokes, especially across the 40 through 6 meter bands. - Frequency range of 1.8 through 54MHz. - RF Power Handling up to 250 watts PEP SSB, 100 watts CW and Digital (at SWR <2:1). - Recommended for general use to isolate either end of a coaxial cable. * Not intended for permanent outdoor use unless mounted inside a weatherproof enclosure. ________________________________________ These chokes are ideal for use at any HF transceiver or receiver antenna connection, portable, mobile or base. In most cases, DXE-LPFC-BNC prevents RFI, stops stray RF and noise on the feedline from getting into the receiver that would cover up weak signals, and improves efficiency of the antenna system. For any station, including POTA and SOTA, mobile and base, DX Engineering Low Power Feedline Chokes keep the RF controlled.

Not Yet Reviewed

$59.99

  • 1
  • Page 1 of 1