Availability
2 Results Found For "Receive Preamplifier"
Moonraker MRP-2000 MK2 25-2000 MHz Scanner Preamplifier
This is the fantastic MRP-2000 MK2 wideband pre-amplifier for scanners or receivers! It covers 25-2000MHz with up to 20dB gain. It comes complete with BNC connectors and patch cable and requires an internal 9 V battery for immediate use! It can also run on 9 -15 Vdc. Boost the power of your scanner and hear those long-distance signals! Specifications: * Frequency Range: 25 to 2000 MHz * Gain: +6 to 20 dB * Impedance: 50 ohms * Weight: 15g (0.54 lbs.) * Size: 100 x 53 x 38mm (3.937 x 2.087 x 1.496 in.) * Power, Internal: 9V battery * Power, external: 9 to 15 Vdc via, 2.1mm power jack, center positive
( 10 )
$82.99
DX Engineering Clifton Laboratories Z10000 Buffer Amplifiers
DX Engineering Clifton Laboratories Z10000 Buffer Amplifiers may be the products most often requested by radio experimenters and electronics enthusiasts. These are the very popular circuits, designed by Jack Smith, K8ZOA (SK), that are crucial for adding a SDR receiver and panadapter display capabilities to a receiver or transceiver which lacks that feature. The Z10000 Buffer Amplifier's high-input impedance can safely tap the early-stage broadband Intermediate Frequency (IF) signal from inside your radio and feed the buffered and amplified low impedance IF signal to your external SDR receiver. It can then produce a spectrumscope - waterfall display pattern of the receiver signals on a compatible tablet or monitor and PC that is running the appropriate third party SDR software. DX Engineering offers two Clifton Labs Buffer Amplifier Kits to add an IF output SMA connector to the rear panel of your radio: * The DXE-Z10000U-KIT is the Universal Buffer Amplifier Kit that covers 50 kHz to 100 MHz. This kit is designed for those willing to do an internal modification, and will output the IF signal of virtually any receiver or transceiver that has an IF in that range. However, the DXE-Z10000U-KIT can be used as a buffer and low-gain preamp between any low level RF devices that operate in that range. As a buffer, this circuit provides over 90dB of reverse isolation to protect the IF stages of the radio from possible birdies on an SDR receiver input. So, even if your radio has an IF output connector, the DXE-Z10000U-KIT may be used externally, with a user-supplied shielded metal enclosure, to be certain to maintain proper radio operation. * The DXE-Z10000K2-KIT is the Buffer Amplifier Kit specifically tuned to the 4.915 MHz IF signal of the Elecraft K2 transceiver. It offers the same high reverse isolation, plus the added benefit of a tuned IF input with a narrower bandwidth of operation and a potentially a lower noise floor on the output. Both Buffer Amp kits contain the updated, completely assembled and tested DX Engineering Z10000C PC Board with a nominal 6.5 dB gain, retaining all the benefits of the reliable original Z10000B boards. Both kits include our finished printed circuit board, required coaxial cables assemblies with special connectors, insulating materials, and hardware—all for an easier installation than ever before! A third party SDR receiver, software (typically free) and compatible tablet or PC and monitor are required to make use of the IF signal provided by the Z10000 Buffer Amplifier and see the signals that your old radio can hear. Due to the high number of specialized radio installations, no printed instructions are included with these buffer kits. Instructional web links are found on the part detail webpages. Installation web documents and videos are only available online. The legacy that was built by Jack Smith, K8ZOA (SK), with Clifton Laboratories, lives on with select products, exclusively from DX Engineering. NOTE: DX Engineering cannot provide electronic technical support of devices installed in user radios and is not responsible or liable for damages that occur to a user radio due to improper or erroneous techniques during the installation of this product. Unplug all electronic devices when working on them and observe all electrical safety and electrostatic discharge precautions when opening sensitive electronics. Modification of a radio should only be attempted by individuals with advanced experience on electronic circuit repair and operation.
( 24 )
$51.99
—
$61.99