Selected Filters


Availability


3 Results Found For "Receive Array"

Part Groups

Results 1 - 3 of 3

YCCC Vertical Array Directional Switch Console Kits

Closeout- Other YCCC array components are no longer available YCCC Vertical Array Directional Switch Console Kits were used to control the YCCC vertical array combiner/controller units, which have been discontinued. They feature an attractive cabinet with an ergonomic direction-selector knob and direction indicating LEDs. Power Pole type connectors are used for DC power connection. These kits require component-level assembly and soldering parts to a PCB. The switching console is installed in the shack, with the control cable run from the switching unit to the combiner/controller unit at the array. Power for the entire antenna system is provided by a 13.8V DC (1A capability or greater) power supply that the user must provide. Use of a "wall wart" type of power supply is not recommended because they generally have very poor DC regulation. These switch units are for use ONLY with YCCC vertical antenna arrays, which are discontinued and no longer available for sale. All inquiries and technical support for these YCCC kits and kit packages is handled by e-mail only, typically within two to three business days: yccctechsupport@verizon.net

Not Yet Reviewed

$60.00

DX Engineering Receive Feedline Transformers

DX Engineering Receive Feedline Transformers are designed to match your receive antenna 75 ohm output impedance to the nominal 50 ohm input impedance of most receivers. These transformers may be used in almost any receiving application that requires a 75 ohm Type F connection to a 50 ohm BNC connector. These transformers have very low loss (<0.3 dB) and very wide bandwidth, 100 kHz to 30 MHz! Matching the receive antenna or array to the receiver ensures the best possible performance as a result of a system impedance match. *Important! - These Feedline Transformers are Intended to be used on an RF ONLY coax and should NOT be used for power.

5.0 out of 5 stars ( 1 )

$55.99

DX Engineering Transceiver Amplifier Keying Cables

DX Engineering Transceiver Amplifier Keying Cables connect the "ground on transmit" or contact closure provided by the radio that is required to make an HF amplifier switch from "receive mode" to "transmit and amplify mode" when using PTT (push-to-talk), VOX or break-in CW keying. DX Engineering Transceiver Amplifier Keying Cables are made for specific transceiver models that have special DIN or mini-DIN connector accessory ports which provide the transceiver's only connections for linear amplifier keying. One type of amplifier keying cable has one RCA phono plug for the amplifier relay jack, which is all that is needed. When the transceiver PTT (push-to-talk) is keyed, the RCA plug center pin is connected to the shield (and chassis ground in most cases) to key the amp relay or its solid state keying circuit. Instead of a direct connection to the amp relay, the RCA plug may be connected to the keying input of an accessory device (DXE-KEYLINE-3, DXE-RTR-2 or DXE-NCC-2), amplifier keying interface (DXE-SV-KR or legacy Ameritron ARB-704 or KD9SV Products SV-KR) or other amp keying line interrupt device, such as a meter or an array controller. Each has a keying input and a keying output for the amplifier relay or another accessory. Another type of amplifier keying cable has two RCA phono plugs, one RED plug for the amplifier relay jack and one WHITE plug for ALC (Automatic Level Control) voltage from the amplifier. The legacy ALC connection does not need to be used with present era solid state transceivers and most modern amplifiers. ALC was required for use on transmitters with tube finals. Some modern amplifiers do not have an ALC output connector. If the amplifier does not have ALC it is okay to leave the WHITE plug disconnected. Order your DX Engineering Transceiver Amplifier Keying Cables to connect to your transceiver accessory port for keying amplifiers, sequencers, receive-transmit interfaces, buffer relays, and other accessories. NOTE: To enable the function of this keying cable, some late model Kenwood transceivers require menu activation of the amplifier keying circuit.

4.8 out of 5 stars ( 51 )

$51.99

—

$59.99

  • 1
  • Page 1 of 1