Availability
10 Results Found For "anchor"
DX Engineering Radial Wire Metal Anchor Pins
DX Engineering radial wire metal anchor pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your radials during lawn maintenance. They are manufactured from 11-gauge steel and are 6 in. long to help keep the cables buried properly.
( 39 )
$59.99
DX Engineering Vertical Antenna Guying Kits
Some vertical antenna manufacturers indicate that their antennas do not need guying. During times of high winds or ice loading, however, some of these vertical antennas may sustain damage or fail altogether. With the small amount of effort needed to install one of these DX Engineering Vertical Antenna Guying Kits, the risk hardly seems worth taking. They feature a 4-point guying scheme that provides the best mechanical advantage to prevent wind stress, regardless of direction. The guying is intended for stability only and should never be depended on for primary support. DX Engineering Vertical Antenna Guying Kits are especially recommended for use with DX Engineering tilt bases, because just one of the guy ropes has to be loosened when you tilt the vertical down. The remaining guys help to stabilize the vertical in three directions when being raised. These kits have been designed to be used with ground-mounted quarter-wavelength vertical antennas, such as DX Engineering monoband and multiband verticals and the Hustler 4, 5, and 6-BTV models. Using the DX Engineering vertical antenna guying kits, you can install four guy ropes approximately halfway up the vertical antenna system to ground level and angled at approximately 45 degrees. Guying should be tightened just enough to permit the antenna to swing a few inches. The ends of the ropes are tied to the earth anchors that are screwed into the ground at about the same angle as the ropes. Tie the other ends of the ropes to the vertical antenna just above one of the antenna element clamps or traps (a guying ring is not required). Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. The DX Engineering Vertical Antenna Guying Kits are available in different lengths to fit your varying vertical antenna needs.
( 9 )
$61.55
—
$89.12
ROHN TBSAFETY Turnbuckle Safety Kits
ROHN TBSAFETY Turnbuckle Safety Kits include 45 ft. (15 ft. per guy anchor assembly) of 1/4 in. high strength guy wire to secure your turnbuckles and 6 matching 1/4 in. forged and galvanized U-bolt clips for final fastening of the safety wire on each of three guy anchors. In other words, use 15 ft. of guy wire and 2 clips on each guy-anchor assembly for protection against turnbuckle loosening or catastrophic failure. Turnbuckles, like all metal exposed to the elements, degrade over time. These safety kits thread through the turnbuckles and guy-line terminations (thimbles and eyes) in figure-8 fashion to make everything secure. Don't allow your tower to collapse due to turnbuckle failure. Order your ROHN TBSAFETY Turnbuckle Safety Kits from DX Engineering and make your tower installation safer!
Not Yet Reviewed
$71.99
PolyPhaser Coaxial Lightning Protectors
PolyPhaser Coaxial Lightning Protectors are designed for general, single-transmitter use in the 1.5 to 700 MHz frequency range. PolyPhaser protectors are available in two mounting styles: "Bulkhead Mount" protectors have a longer connector and hardware to mount it through the grounding panel. "Flange Mount" protectors anchor to a grounding panel with both connectors parallel to a flat surface. PolyPhaser Coaxial Lightning Protectors use a DC blocked specially configured gas tube design that has no DC continuity between the two center pins. PolyPhaser's multi-strike products are designed to pass RF frequencies and block all DC. These protectors appear as a DC open between surge and protected ports and offer industry-standard protection. PolyPhaser protectors are suitable for all types of antennas, even "floating" antennas that are not DC grounded. With PolyPhaser DC Blocked protectors, any slow voltage build up from wind driven rain, snow or dust, will not get to the equipment. As the protector reaches threshold for turn-on in a dc blocked circuit, it will go into a momentary soft turn-on as the gas barely ionizes and bleeds the static charge to ground. This does not create noise since it will not get to the arc mode and lasts only a short time. PolyPhaser protection devices have been chosen and specified by communications systems engineers and technicians for 24/7 service in broadcasting, commercial, military and government installations. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Trusted by Amateur Radio operators for over 40 years, PolyPhaser Coaxial Lightning Protectors are ready for your antenna system installations. They are available here, at DX Engineering.
( 64 )
$93.99
—
$99.99
Chameleon Antenna CHA Sling Bags
Chameleon Antenna Sling Bags are the perfect companion for your Chameleon MPAS 2.0 series antenna and all of its accessories. The bag is made with water and abrasion resistant 900D Oxford cloth and will survive most things that you will throw at it in the field or on the summit. Featuring a pair of large pockets on the front with adjustable buckle closures for small items such as matching networks and coax. Internally, this 30 x 6in. bag has straps for holding items in place. A padded shoulder strap ensures comfort while carrying the bag in a sling configuration and padded handles on the side ensure comfort and options for transport. Molle straps provide for additional points to use to anchor items needed for successful portable operation. Specifications: • 1 x Chameleon Antenna Velcro Patch • Double Layer Water Resistant • Single Shoulder Strap w/ Buckle Adjustment • Interior Straps • Side Handle • Heavy Duty YKK Zippers For Side Opening • 2 x Large Front Pouch w/ Buckle Adjustment • Molle Straps • Weight: 4.5lbs. • Material: 900D Oxford cloth • Color : Tan • Dimensions: 30.0 x 6.0in.
( 2 )
$80.00
DX Engineering Tinned Copper Radial Wire
DX Engineering Tinned Copper Radial Wire is the same wire as used by the most successful contest stations and DX enthusiasts for their ground-mounted vertical antennas. This 16 AWG tinned solid copper wire is an extremely cost effective solution for the high-count, full-size ground radial wire systems that are required for top-performing HF vertical antenna installations. This is especially true for 4-element Four Square Array Systems, 3-element ProStack Arrays, and 2-element Dual Vertical Arrays. Why is this wire the absolute best choice for any ground-mounted vertical antenna? Because, DX Engineering Tinned Copper Radial Wire will last much longer in a variety of soil conditions as compared to bare copper, copper coated steel and aluminum wires. Unfortunately, radials deployed with those other wire types actually corrode and degrade rather quickly, but do so slowly enough that the operator may not easily perceive that degradation in terms of antenna system performance. Full radial system integrity is maintained for a much greater number of years with tinned copper wire. Depending upon soil type, installations with DXE-TCRW16 will maintain vertical antenna performance for many, many years… and even decades. DXE-TCRW16 is available in small, easy to handle spools in lengths of 500 feet (DXE-TCRW16-500), 1,000 feet (DXE-TCRW-1000), 2,500 feet (DXE-TCRW16-2500) and 5,000 feet (DXE-TCRW16-5000). NOTE: To prevent accelerated corrosion and the possibility of noise, do not use metal anchor pins (lawn staples) on Tinned Copper Radial Wire. Use only DXE-STPL-100BD Biodegradable Anchor Pins to hold down bare wire radials. DX Engineering Tinned Copper Radial Wire is the right choice for long lasting top-performance radial systems for your ground-mounted vertical antenna system.
( 2 )
$99.99
CHAMELEON ANTENNA Universal Guying System
The CHAMELEON ANTENNA Universal Guying System was the brainchild of the internal lab testing and development. While the need to support the taller and heavier vertical antennas, CHAMELEON ANTENNA developed this portable and lightweight guying system. Constructed of non-conductive guy wire, corrosion-resistant stainless steel anchors, and heavy-duty nail pegs. The Universal Guying System consists of these components: * Three winder assemblies * Three lengths of 25 feet, 3mm-P Mastrand cord * Three nail plugs * Three line tighteners * Delta guy ring Count on CHAMELEON ANTENNA Universal Guying System when erecting your next portable vertical antenna!
( 4 )
$65.00
Klein Tools Cushion-Grip Nut Drivers
Klein Tools manufactures these drivers out of industrial-grade materials to ensure performance and durability. A heavy-duty hollow shaft will give a tight, solid feel and the cushion grip handle provides for greater torque and comfort. Klein Tools incorporate color-coded ends to make it easy to find the one that you need. These nut drivers have 3 in. long chrome plated hollow shafts and are flanged inside of the handle for a solid, twist-resistant anchor.
Not Yet Reviewed
$59.99
Flag Pole Buddy RV Ladder Brackets
Get on the move with Flag Pole Buddy RV Ladder Brackets. These antenna buddies are the safest, easiest way to temporarily mount your mast and HF/VHF/UHF antenna. Flag Pole Buddy mounts offer a unique 2-piece system manufactured from "bulletproof" fiberglass-filled nylon that provides superior support in high winds with no rubbing against your RV. A simple one-time installation to your ladder or the back of your motor home, and you're ready to safely slide and anchor your mast in place while standing on the ground… no more ladder climbing or step stools! And removal is just as quick and easy. You've got a ham shack on wheels when you mount hassle-free Flag Pole Buddy RV Ladder Brackets from DX Engineering.
( 2 )
$69.99
—
$73.99
DX Engineering Phillystran Steel Tail Kits
DX Engineering Phillystran Steel Tail Kits provide the appropriate transition from non-metallic to metallic guying cable at the ground end of tower guying systems. Steel Tail Kits are available for Phillystran HPTG-4000I, -6700I and 11200I Guy Lines. What is the function of the steel tail? Here is the recommendation by Phillystran, the manufacturer of HPTG-I High Performance Tower Guy non-metallic guy lines: A steel tail is a length of EHS (Extra High Strength) steel guy line connecting the HPTG-I assemblies to the turnbuckle or guy anchor. The steel tail protects the HPTG-I assemblies from damage due to brush fires, lawn maintenance equipment or vandals. The steel tail length should be sufficient to get the bottom end of the HPTG-I assembly above arm's reach, or above brush tops (if located in a marsh or tall brush area). The HPTG-I should never pass through tree limbs or be allowed to rub against poles or trees. The steel tail allows for easier guy length calculations and serves as a guy tension monitoring point, as well as a safer area to attach guy grips during guy line installation and tensioning. Eliminating the hassle of buying a length of steel cable and obtaining a special tool to cut it, DX Engineering Phillystran Steel Tail Kits provide everything needed to isolate your tower's non-metallic guy cable from harm. Three different size kits are available for different tower guying requirements provided by Phillystran guy cables 4000I, 6700I and 11200I. Here are the items included in these innovative Steel Tail kits: - 12 ft. EHS steel guy line, Galvanized, in three kit sizes, 3/16 in., 1/4 in. or 5/16 in. - Porcelain Guy Line Strain Insulator, 502 or 504 depending upon kit size - Galvanized Steel Preform Dead End Big-Grips for EHS steel guy line, two per line - Heavy Duty Thimble, galvanized steel, appropriately sized for each kit - Cable Ties, UV protected Black, four, to secure installed Big-Grip ends Note: Phillystran guy line and Preform Dead End Big-Grips for Phillystran are not provided in this kit and must be ordered separately. DX Engineering Phillystran Steel Tail Kits provide Porcelain Guy Line Strain Insulators for the top end of the Steel Tail so that the galvanized steel Big-Grips for the Phillystran and for the EHS Steel Guy Lines do not touching and make RF noise. For three different size Phillystran guy line, HPTG-4000I, -6700I and -11200I, these kits are available exclusively from DX Engineering in 3-packs for each level of tower guying.
( 2 )
$79.99
—
$88.99