Selected Filters


Availability


6 Results Found For "Receive Array"

Part Groups

Results 1 - 6 of 6

Hi-Z® Antennas PC-8PRO 8 Circle Array Phasing Controller

The Hi-Z Antennas PC-8PRO 8 Circle Array Phasing Controller is the primary component in the Hi-Z Antennas Eight Element V2 Multi-Band 8 Circle Receive Array System, intended for 160-, 80- and 40-meter band coverage, with useful functionality from 500 kHz to 15 MHz. The HIZ-PC-8PRO Phasing Controller and system components combine to provide an effective directional receive pattern that is electronically switchable to eight different directions. The Hi-Z Antennas Eight Element V2 Multi-Band 8 Circle Receive Array System provides enhanced signal-to-noise performance with Receive Directivity Factor (RDF) approaching 12dB and up to 35dB array front-to-back! The HIZ-PC-8PRO is the heart of this antenna which provides dramatically improved reception over transmitting antennas. It properly combines signals from eight receive short element active verticals which are each ground-mounted on a ground rod, in a circle. DXE-RSEAV-1 are sold separately, which use DXE-AVA-3 Element Amplifiers. Sharper cardioid patterns with deeper reverse nulls are developed by the 8 Circle than other arrays. This Phasing Controller and other system components provide an effective receive pattern that can be electronically rotated to eight different directions: typically, 45, 90, 135, 180, 225, 270, 315 and 360 degrees. Standard 85 ft. diameter 8 Circle Arrays provide 160-, 80- and 40-meter band coverage with an exceptional cardioid pattern, supported with the updated delay cables HIZ-DL4-60-85 (Long and Short, sold separately). Alternatively, choose HIZ-DL4-80-113 cables (Long and Short, sold separately) for a 113 ft. diameter 8 circle which increases performance on the 160 and 80 meter bands. The HIZ-MDC-8PRO is the required Manual Directional Control Switch Console, sold separately. The HIZ-PC-8PRO also serves as a replacement part for Hi-Z 8 Circle system owners to order Hi-Z PC-8PRO V2 Phasing Controller. See the listing for more information.

5.0 out of 5 stars ( 1 )

$649.00

DX Engineering Receive Four Square Array Electronics Package

DX Engineering Receive Four Square Array Electronics Package, DXE-RFS-SYS-2P, is for the array builder who wants to use their own passive receive verticals for a mono-band receive array. See the DXE-R4S-SYS-V3 for the Complete Receive Four Square V3 Array System with Receive Short Element Active Verticals. DX Engineering Receive Four Square Arrays dramatically improve reception of weak distant signals with excellent rejection of extraneous signals and noise. This four-direction switchable array uses time delay phasing of four physically short receiving vertical elements. The resulting directional receiving pattern is superior to four short Beverage antennas and typical two or three element arrays. The Receive Four Square is less susceptible to high angle signals than EWE, Flag, Pennant, K9AY and SAL antennas. This type of receive array, using physically short vertical elements, limits signal and noise for dramatically superior weak signal reception, as compared to full size transmitting antennas and arrays. With proper spacing of four unobtrusive, physically short vertical elements, the Receive Four Square Array System provides high performance directional receive for HF Amateur, SWL or AM DXing. Click or tap the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. DX Engineering Receive Four Square Arrays offer directional performance comparable to four long Beverage wire antennas, using far less land area. This Controller and Switch Console package is designed to be used with four identical, user-supplied, active or passive symmetrically-spaced ground-mounted vertical elements to provide switching for a 4-direction receiving antenna system. Passive elements will generally provide an optimized monoband receiving system. Conversely, with four DX Engineering Receive Short Element Active Vertical antennas, DXE-RSEAV-1, the properly sized array can achieve excellent directional receiving performance over three HF bands. Build an exceptionally effective, electronically rotatable, stationary receive antenna that lets you hear the DX that cannot be heard on a transmit antenna. Dig the weak signals out of the noise with an antenna that can help make your station one of the best; install the DX Engineering Receive Four Square Array System. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents NOTE: Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.

Not Yet Reviewed

$553.98

Manufacturer Rebate

ICOM IC-R15 Wideband Handheld Receivers

ICOM IC-R15 Wideband Handheld Receivers allow both the beginner and experienced user alike to discover the exciting world of radio reception. The IC-R15 covers a wide frequency range from 108 - 500 MHz, allowing you to receive a diverse array of radio signals, whether it's VHF Aeronautical Radio in AM, Amateur Radio on 2m and 70cm, Railway, Marine, or regional broadcast stations in AM/FM and Wideband FM (WFM) from 76 – 500 MHz. The versatile and reliable IC-R15, with its state-of-the-art technology and elegant design sets new standards and ensures that even users with minimal experience can quickly get on the air.

5.0 out of 5 stars ( 1 )

$559.95

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables

DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.

Not Yet Reviewed

$699.99

DX Engineering Phased Array Quarter Wave Tuned Cables

DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.

4.67 out of 5 stars ( 3 )

$649.99

I0JXX Mast Mount Low Noise Preamplifiers

I0JXX Mast Mount Low Noise Preamplifiers offer high gain amplification with excellent noise figures in VHF and UHF amateur band optimized devices for casual operation or contest-grade directional antenna systems. Built for long-term tower top use, two high-power SPDT coaxial relays are used to protect the internal, band-specific I0JXX LNA using low-loss and high-isolation interconnections. These exceptional components are housed in a specialized weather and UV resistant polyamide black case with a drip edge surrounding two downward facing Type N female connectors mounted on a rugged, 12 gauge (2mm) aluminum panel. A separate female BNC is for DC power and control voltage, intended to be sent from the required sequencer via an inexpensive coaxial cable. Extraordinary receive-transmit-receive changeover performance is achieved by these compact 12VDC mast mounted units. Their internal LNA (low noise amplifiers) offer preamplification using ultra-low noise components as good or better than a typical receiver front end, which preserves the capabilities of a low-noise antenna or stacked array and the transceive system. The internal relays are connected to bypass the internal preamplifier when power is removed. An I0JXX SEQJXXBOX Sequencer can be used to control the I0JXX Mast Mount Low Noise Preamplifiers for two-way VHF or UHF communications. I0JXX Mast Mount Low Noise Preamplifiers are built with high quality components for many years of service. View the band unit specific specifications on each part detail page.

Not Yet Reviewed

$700.99

  • 1
  • Page 1 of 1