Availability
Parts and Accessories
DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas
New Name...Same Antenna! DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas are designed for low-noise reception of signals within the frequency range of 100-kHz to 30-MHz. Their integral, extra-high dynamic range, low-noise preamplifier is designed for minimum intermodulation distortion in the presence of very high-level signals that would normally overload most preamplifiers. Read more about the exclusive Clifton Laboratories design of the loop's RF-30 preamplifier by clicking "More Details" below. RF-PRO-1B Active Magnetic Loop Antennas, formerly known as the "Pixel Loop" and recently as InLogis, are now manufactured and serviced by DX Engineering. For Amateur Radio operators, AM DXers and Short-Wave Listeners, these active loop antennas are a great way to extend your listening ability. Add DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas to your radios and start hearing more signals with less noise! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 26 )
$809.99
Times Microwave Systems® Bulk Coaxial Cables
Times Microwave Systems Bulk Coaxial Cables are recognized as superior RF cable products. The standard Times Microwave LMR® is a UV-resistant polyethylene jacketed cable designed for 20-year service in outdoor use. Depending upon size, LMR® cable has a solid copper or copper clad solid aluminum center conductor. Their bending and handling characteristics are significantly better than air-dielectric and corrugated hard line cables. LMR-DB® cable has a waterproofing compound to prevent moisture intrusion after a minor abrasion. Times Microwave Systems EZ Series and TC Series connectors are suitable for use on standard LMR® and LMR-DB® cables. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center and a rubber jacket (black thermoplastic elastomer) designed for repeated bending. Times Microwave TC Series crimp connectors are designed for use on LMR® UltraFlex cables. LMR®'s RF shielding is typically 50 dB greater than standard coax. The copper shield and multi-ply bonded foil outer conductor is rated conservatively at greater than 90 dB. That's better than 180 dB isolation between two adjacent cables. A wide variety of connectors are available for LMR cables, including all common interface types, reverse polarity, and a choice of solder or non-solder center pins. Most LMR connectors employ crimped outer attachment using standard hex-crimp methods. Times Microwave Systems is a premier supplier of coaxial cable products worldwide. Only Times offers a range of products specifically developed to perform as needed in the most diverse range of environments. Times Microwave Systems has over 60 years of experience in building the highest-quality cables. Order LMR® coaxial cables from DX Engineering and put Times Microwave Systems Bulk Coaxial Cables to work for you! LMR® is a registered trademark of Times Microwave Systems.
( 106 )
$874.99
Yaesu G-5500DC Azimuth-Elevation Rotator Systems
Yaesu G-5500DC Azimuth-Elevation Rotator Systems are specially designed to accommodate horizontal cross-booms to mount pairs of VHF and UHF directional antennas for space communications. Providing simultaneous control of 450 degrees of azimuth rotation and 180 degrees of elevation rotation, they are perfect for EME (moon bounce) and satellite communications installations. The G-5500DC dual controller lets you adjust and keep track of both aspects of the antenna system's positioning. The 120 VAC controller includes an interface jack for computer control, supported by the optional GS-232A Computer Controller, as well as many aftermarket control programs and interfaces. These azimuth and elevation rotators are actually two separate motor units, now DC controlled. They may be mounted together on a mast with the included mast bracket, or independently with the azimuth rotator inside a tower and the elevation rotator mounted on the mast above the top of the tower. They handle a total of about 10 sq. ft. of antenna wind load and rotate each way in about one minute. The Yaesu G-5500 AZ-EL clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-5550DC azimuth and elevation motors operate with two independent 22 V DC control lines, each a five-wire system, using the same connectors at the end of the control cable as the previous models. Both of the new DC motors, azimuth, and elevation, are marked "G-5550DC" at the connector. Be sure to mark your connectors AZ or EL. The rear panel of the controller is titled "G-5500DC" on the serial number label. WARNING: The legacy Yaesu G-5500 Rotator motors and controller used a 26 VAC control voltage, six-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-5500DC components, which only use pins 1, 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use five-conductor, 20 gauge control cable (5 x 20 AWG). If the rotator cable needs to be longer than 125 ft. then use five-conductor 18 gauge cable (5 x 18 AWG). The input voltage for the G-5500DC controller is labeled "117 VAC" to indicate house current range of 110 to 120 Vac. When you are launching your EME or satellite communications adventure, an azimuth/elevation combination rotator is a vital tool for your antenna system. As durable as they are attractive, Yaesu G-5500DC Azimuth-Elevation Rotator Systems are available from DX Engineering.
( 17 )
$969.99
Yaesu G-1000DXA Heavy-Duty Rotator Systems
Yaesu G-1000DXA Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-1000DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-1000DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 23 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-1000DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-1000DXA Heavy-Duty Rotator System from DX Engineering.
( 14 )
$799.99
DX Engineering Premier Telescoping Carbon Fiber Masts
DX Engineering Premier Telescoping Carbon Fiber Masts are the superior choice for portable and temporary antenna supports. These very high-strength and lightweight carbon fiber masts are available in four extended length versions; 24 foot, 33 foot, Heavy-Duty 33 foot and 49 foot. Their short section lengths allow easy transport and low cost shipping. The longest 49 foot model has a closed length of 81 inches; the other three models slide down to an amazing 69 inches! Surpassing the competition and fiberglass, these black UV resistant carbon fiber tubing masts are super lightweight and ultra-portable. Included lever-action cam-lock clamps secure the next smaller tube in place. Clamps are removable for placement of optional guy rings, and their lever grip is adjustable, both with the included 3mm Allen wrench. Each different size clamp mounts securely on a lower tube and its integral cam lock lever allows fast and easy telescopic mast raising and lowering. DX Engineering Premier Carbon Fiber Masts are lighter than aluminum and fiberglass and stiffer than steel of the same thickness. Their resistance to corrosion and breakdown is the best of these four temporary mast materials. Each section features a red color at the bottom to indicate minimum overlap when extending. Click on each model for specific dimensions and number of sections and clamps. These are the ultimate quality carbon fiber masts for portable and temporary antenna supports. Wherever you go and however you get there, DX Engineering Premier Telescoping Carbon Fiber Masts are the absolute best choice for your next portable antenna adventure.
( 24 )
$824.99
DX Engineering NCC-2 Receive Antenna Phasing Systems
Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!
( 19 )
$955.99
On Sale
RigExpert Antenna Analyzers
RigExpert Antenna Analyzers are powerful antenna analyzers designed for testing, checking, tuning, or repairing antennas and antenna feed-lines. Mainly, these are SWR (Standing Wave Ratio) and impedance measurement instruments (vector impedance analyzers). Their large, bright LCD screens provide graphic illustration of SWR, impedance; return loss, and much more. Easy to use measurement modes, as well as additional features such as connection to a personal computer (to plot SWR, R, X and Smith charts, etc.); make RigExpert Analyzers attractive for professionals and hobbyists alike. They are compatible with several operating systems, including Windows© 10, 11 and Mac, with software download*. The graphic display of various parameters over a wide frequency range is a key feature of these analyzers. This significantly reduces the time required to adjust an antenna. ZOOM models allow you to zoom-in on graph points for clearer analysis. USB connection allows export of sweep files with Antscope for Android or Antscope2 software to PC or MAC. *(download from the manufacturer https://rigexpert.com/products/software/). Many models have Bluetooth for direct file transfer for galvanic isolation without a USB cable, which provides the most accurate measurements. RigExpert Antenna Analyzers are available in several models with greater frequency range of operational features. Some have SO-239 UHF female connector, except for most models that operate at 230 MHz and above that have a Type N female connector. An array of options are available to cover almost any need for the professional and the Amateur. The following tasks are easily accomplished by using RigExpert Antenna Analyzers: * Rapid check-out of an antenna * Tuning an antenna to resonance * Antenna SWR and impedance measurement and comparison before and after a specific event (rain, hurricane, winter, etc.) * Making coaxial lines or measuring their parameters * Cable testing and fault location * Measuring capacitance or inductance of reactive loads *Send data to laptop for larger graphical display and further analysis. Note: For additional product information, please look at the files under the "Documentation" tab. When you need a versatile antenna analyzer for Amateur Radio or professional use, you'll find that one of these RigExpert Antenna Analyzers, from DX Engineering, will be well suited to the task!
( 513 )
$929.95
—
$1,139.95
$899.95
—
$999.95
Toptek Communications PA-350V VHF 135-165 MHz 350W Power Amplifiers
Toptek Communications PA-350V VHF 135-165 MHz 350W Power Amplifiers are advanced and versatile high-power linear amplifiers designed for Amateur Radio 2 Meter FM, SSB and CW operations and Commercial VHF. A large, easy-to-read green backlit Alphanumeric LCD provides simultaneous digital input power, output power, SWR readings. Front panel button actions and specialized, user-defined function readouts and menu selections are displayed, including incremental 100, 200, 300 and 350W power output settings. This VHF amplifier* delivers approximately 300 watts output with only 5 watts input from an HT or 350 watts maximum output with a VHF mobile. The PA-350V has two selectable input ranges, Low 15W max and High 30W max, achieving 350 watts output with either 10 watts input or 15 to 25 watts input, to accommodate almost any VHF transceiver. Multiple protection circuits, a Receive Low Noise Amplifier (LNA) with bandpass filter, RF sense or PTT keying (required for SSB/CW) and thermostatically controlled fans are some of the great features of this top-of-the-line Toptek amplifier. True 50 ohm Type-N RF connectors maintain the highest efficiency to the feedline and antenna. NOT compatible with DMR and P25 modes NOTE: Rear panel accessory jack (4-pin mini-DIN) is provided for the accessory REMOTE Control Panel, TEK-REMOTE. *Requires 13.8 VDC @ 50A max. (External power supply not included).
( 18 )
$879.99
RM Italy MLA300 HF Linear Amplifiers
RM Italy MLA300 HF Linear Amplifiers are broadband linear amplifiers designed for operation from 1.8 to 30 MHz (160–10 meters), delivering up to 300 watts of average output power. It supports input power levels from 1 to 15 watts, making it compatible with most modern QRP transceivers. Powered by four MACOM MRF455 transistors in two parallel push-pull AB-mode circuits, the MLA300 provides clean, reliable operation for SSB, CW, AM, FM, and digital modes.
Not Yet Reviewed
$836.99
EAntenna HEX6B Six Band Hexbeam Antenna
EAntenna HEX6B Six Band Hexbeam is a directional HF antenna for the six Amateur bands 20, 17, 15, 12, 10 and 6 meters. This design follows the ideas of G3TXQ Steve Hunt, the originator of the Broadband version of the Hex Beam antenna. However, this mechanical construction is a version refined by EAntenna with their long-standing antenna engineering experience. The result is an efficient, lightweight portable antenna for the high HF DX bands, which is ideal for use for DXpeditions and vacations. An installation at 20 ft. above the ground can work quite well, but a tower-mounted Hexbeam at a height of 35 to 60 ft. is known to perform as intended and produce excellent DX results. The HEX6B works as two element beam on each band. Ready-to-use wires and ropes are attached to the fiberglass struts and due to the mechanical tension of the struts, the beam is stretched to its fixed size all the time, so there is no sag on the wires. The radiator dipoles are connected to the vertical center support, with each band wire element attaching with screw clamps. The center support is designed as a coaxial transformer and balun, providing a particularly good match on each band, with one feedline for all six bands. The HEX6B forward gain is approximately 3dBD or better, the front/back ratio is between 13 and 22dB. SWR is 1.5:1 or better on all bands except 10m, where SWR is 2:1 or better. Each band can be used in full bandwidth without a tuner. The maximum allowed power is 5 kW. The fiberglass tubes are double coated against UV radiation. The setup of the HEX6B six band beam is simple and can be done by one person in about 30 minutes. All ropes and wires are ready, cut to length, so no tuning is required. Due to the low weight of only 18.7 lbs. (8.2 kg) this hex beam can be installed on a light aluminum push-up mast. Rotation is either done with a small rotator or by hand. The HEX6B mast clamp accommodates poles with a Diameter from 1.10 -2.05 in. (28-52mm).
( 6 )
$851.99
DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas
DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas are 43 ft. tall, high performance, 160 through 10 meter vertical antennas - designed from the ground up to offer ease of use, reliability and performance! New design and materials technology are used throughout. The patented* and massive SAF-T-TILT™ 3/8 in. thick rugged aluminum base allows easy, safe tilt action without the unsafe removal of mounting hardware -- as with some competitors' antennas! Now - using our ground-mounted vertical, you'll work DX as you never could with a low horizontal-dipole antenna! DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas require a special DX Engineering DXE-UN-43 UNUN with 150 ft. of RG-213 coax feed and your wide-range tuner - OR a automatic tuner at the base of the antenna without the UNUN.. These MBVE-5A verticals feature: * High strength Delrin® thermoplastic insulator that won't crack, splinter, peel or fail from exposure * Rugged structural grade type 6063-T832 drawn aluminum tubing radiator - the best alloy for high-strength, long-lasting antenna applications * New, massive, patented* SAF-T-TILT™ base allows safe raising and lowering of antenna without removal of fastening hardware * The fast taper antenna element provides the lowest wind resistance * Free-standing to 92 mph wind speeds * All Stainless Steel hardware - very durable and attractive MBVE-5A verticals include the antenna element, mounting plate with insulator, exclusive Patent Pending SAF-T-TILT™ Base, stainless steel hardware and clamps. Like any HF vertical, MBVE-5A verticals require a good ground radial system. 32 radials, 65 feet long are recommended. Fewer or shorter radials will work, but with some diminished results. For proper installation, additional materials are needed, but not supplied. You will need: * Mounting pipe--steel pipe that has 2.0 in. O.D. with 0.25 in. wall thickness, 4 ft. long -- standard 1-1/2 in. galvanized water pipe (with its 1.9 in. OD) is fine * Quick-Set or other concrete for mounting pipe installation * Radial wire and wire lugs--must use 14-gauge, stranded copper wire with PVC insulation. A minimum of 20 radials, each 32 feet long, should be used. * Penetrox A -- to ensure good connection between aluminum hardware and in-between aluminum tubing sections * Anti-seize compound, which should be used on the threads of all the stainless steel hardware to prevent galling Consider these new, cost-effective DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas and packages now available for your application: -- DXE-MBVE-5A 43 Ft. Antenna only -- DXE-MBVE-5A-4P Antenna Package with Radial Plate -- DXE-MBVE-5A-4UP Antenna Package with UN-43 UNUN -- DXE-MBVE-5A-4UPR Antenna Package with Radial Plate and UNUN Packages with Radial Plates include two extra hardware kits for a total of 60 possible radial wire connections. Packages that include the UNUN also include the UNUN mounting bracket. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. *US Patents D654,063 and D654,064 DX Engineering MBVE-5A Series SAF-T-TILT™ HF Multi-Band Vertical Antennas are high-performance verticals and antenna packages that allow you to access all HF bands with only one antenna solution. Order one of these premium-quality all-band HF verticals from DX Engineering and roam HF… freely!
( 9 )
$846.95
—
$989.61
RigSelect Pro Transceiver Switch and SO2R Controllers
RigSelect Pro Transceiver Switch and SO2R Controllers boast an extensive array of capabilities that make it possible to implement an award winning SO2R station where any two of up to four connected radios can be selected as the SO2R pair, and in any order. Switch one set of headphones, microphone, paddle/key, and PTT line among any of four radios. RigSelect uses quiet solid-state relays for all audio switching, which makes Switching extremely fast and telecom quality relays are used for all Mic, Key, and PTT circuits. Additionally, the RigSelect Pro features a crisp color TFT display for status and menu operations.
( 3 )
$859.99
Yaesu Rotator Units
Yaesu Rotator Units are available as replacements or as stand-alone azimuth positioners for use with a third party controller. They include only the top mast bracket and hardware. Lower mast brackets are sold separately.
( 19 )
$769.99
mAT TUNER mAT-1500PROII Automatic Antenna Tuners
mAT TUNER mAT-1500PROII Automatic Antenna Tuners are multi-purpose high power tuners that can match almost any transmitter and amplifier. Providing Frequency coverage from 1.8 to 30MHz and with two antenna outputs, the mAT-1500PROII also provides antenna switching. Depending on how cables are connected, the tuner will operate in three modes: Icom, Yaesu or General, General mode also allows for remote operation of the tuner. The front panel has a 4.3 inch high resolution display that provides information as to the current operating mode, forward power in both PEP and Average power, with a bar scale that can show three ranges: 15W, 150W, and 1500W; in addition to the power output the antenna system SWR is also shown along with current toggleable settings such as antenna output selection, PTT status, which of the four buttons (LUP, LDN,CUP or CDN) was pressed last, and finally the current status of the tuner. The front panel also has 6 additional buttons for controlling if the PTT signal is passed from the tuner to an amplifier (effectively putting the amplifier in bypass), an online button which controls the tuner being in an online or bypass state, a Tune button which starts a tuning cycle when the tuner is in General mode, a range button which changes the displayed scale of the RF indicator on the display, an antenna select button which allows for changing the antenna jack that is used on the tuner, and finally, a power and screen background setting which allows for tuner power to be cycled in General mode as well as the screen brightness and background color to be changed (if the tuner is in Yaesu or Icom mode, the power function of this button is not used.) The rear panel features 3 SO-239 jacks, one for RF In, and two antenna connections. a ground lug and a handful of connection ports for interfacing with the radio. If the user wants the tuner to follow the frequency of the radio with no additional input, the user can connect the appropriate control cable (sold separately) to the radio and the Icom/Kenwood or Yaesu jacks on the back of the tuner. In these modes, the tuner will receive power from the radio and will power up with the radio and not require a dedicated power connection. In general mode, a connection to the DC in jack is required. A PTT in and Out jack both allow for the transceiver to send a PTT signal to the tuner and for the tuner to pass that PTT signal on to the amplifier. Additional Feature and Specifications: Frequency Coverage: 1.8 to 30 MHz Power Rating: 1500W(SSB), 800W(Data) Tuning Power: 5-15W Tuning Time: < 8 seconds (Programmed), 0.1 seconds (from pre-saved frequencies in memory) Operating Temperature: 14° F - 140° F Frequency memories: 16,000 Power Requirements: 12-14VDC, 2.0A Dimensions: 11.420"x9.567"x3.071" (H x L x W) Weight: 7.72 pounds
Not Yet Reviewed
$799.95
RM ITALY MLA100 HF Amplifiers
RM ITALY MLA100 HF Amplifiers cover all Amateur bands, 160 through 6 meters, providing up to 100 watts output on HF and 80 watts on 6 meters with only 5 watts maximum RF input. They are the perfect choice for medium power operations with today's very capable, low power (QRP) radios, including many brands of portable and SDR transceivers. The MLA100 features PIN diodes for very fast receive-transmit-receive switching am seamless QSK CW fast break-in operation. Band selections are automatically detected and switched or may be set manually. Front panel LEDs display power output and SWR simultaneously on dual bar graphs. MLA100 amplifiers have built in protection from excessive input power, high temperature and high SWR. The MLA100 is a clean and capable standard solid state linear amplifier using two robust Mitsubishi RD1000HHF1 MOSFETs built into a massive, chassis-sized heatsink. The MLA100V is the same amplifier unit with the addition of an externally mounted fan. Both MLA100 and MLA100V HF Amplifiers require 13.8 Vdc at 20 A maximum, and feature a rear panel 20A ATC fuse and DC power quick connector. Also on the rear panel are Input and Output SO-239/UHF female RF connectors and a female RCA phono "PTT" for amplifier keying. Their chassis measure 190 x 182 x 78mm x (7.48 x 7.17 x 3.07 in.) and weigh 1.4kg (3.1 lbs.). *** Note: Amplifier Color may vary. PLEASE NOTE: This amplifier is intended to be used with a low power (QRP) transceiver that is capable of an RF output of approximately 5 watts maximum. DO NOT USE this amplifier with radios that are capable of 100 watts output. Even when output power is turned down, many 100 watt transceivers send out an instantaneous high power RF pulse that will blow out the Solid State final transistors of this amplifier. Damage to final transistors due to RF pulse and overdrive is NOT COVERED UNDER WARRANTY. It is the owner's responsibility to use this amplifier properly, with a low power radio that cannot accidently damage the amplifier. Cost of repair of amplifiers with blown finals will be charged to the customer or will be deducted from the refund of returned amplifiers with blown finals. Available exclusively in North America from DX Engineering, order your RM ITALY MLA100 HF Amplifier to bring new operational capability - and more fun - to your QRP transceiver.
( 14 )
$831.99
—
$851.99
DX Commander Signature 12.4 HF Multi-Band Vertical Antennas
DX Commander Signature 12.4 HF Multi-Band Vertical Antennas are an excellent choice for DX performance and general operations. Efficiently resonant on every HF band of operation, featuring wide SWR bandwidth and low take-off angle, the Signature 12.4 covers the Amateur bands 80 to 6 meters. DX Commander vertical antennas are based on the same principles as a fan dipole, with several vertical wire elements of various resonant lengths connected to a common feedpoint. The wire elements and support ropes are arranged with spacer plates around the non-conductive fiberglass mast. When installed with an appropriate radial system, the Signature 12.4 achieves efficient quarter-wave vertical performance with natural resonance and low SWR on every band, without the need for traps, coils or antenna tuners. Band-hopping DXing and simultaneous multi-band multiplexed operations are supported. The Signature 12.4 antenna is rated at 1500W SSB/CW, 400W FT8 and other digital modes.
( 7 )
$792.79
On Sale
ICOM IC-718 HF All Band Transceivers
ICOM IC-718 HF All Band Transceivers make communicating with the world easy! The superior performance of these HF base transceivers allows you to make contacts over long distances--even to the other side of the world! With excellent receiver sensitivity, a wide dynamic range, high signal-to-noise ratio, and full-duty operation, the ICOM IC-718s offer the latest RF and digital technology in a compact size. Clean, clear audio is easily heard from the front-facing speaker and the IC-718s feature a minimum of switches and controls to simplify operation. Plus, a soft-touch 10-key pad allows for the direct entry of an operating frequency. These are great HF starter transceivers but they will also thrill the accomplished ham, because the IC-718s are very simple to use. The IC-718 HF All Band transceivers will definitely be the most practical DSP rigs you will ever own! They provide many useful features that you want and need--and the price isn't bad, either! Some quick specs: * 160 through 10 meter operation (60 meter channels not available) * Continuously adjustable RF power output -- 100 watts maximum to 2 watts minimum (SSB and CW modes) -- 40 watts to 2 watts (AM mode) * 30 kHz through 30 MHz general coverage receiver * 1 Hz frequency resolution * 101 memory-scan channels Other great features include: * Includes DSP noise reduction and auto notch (UT-106 module) * RF gain control * RF attenuator and preamplifier * Adjustable level noise blanker * IF shift control * Receiver Incremental Tuning (RIT) * Band stacking register * Tuning rate auto step-up function * Digital S/RF meter * VOX operation * Adjustable microphone audio compressor * Electronic CW keyer Note: For additional information, please look at the files under the "Documentation" tab. Supplied accessories include: * Hand-held microphone * DC power cable and spare fuses These little transceivers are great for portable use or as Field Day equipment. They also make great back-up transceivers for well-equipped ham shacks. New Ham or not, one of these IC-718s is a nice addition to any station. Order ICOM IC-718 HF All Band Transceivers from DX Engineering and enjoy some easy QSOs.
( 47 )
$1,099.95
$899.95
Hamplus AS-603WL Automatic Remote HF and VHF Antenna Switches
Hamplus AS-603WL Automatic Remote HF and VHF Antenna Switches provide a new level of affordable convenience. This amazingly intelligent, three-transceiver interfaceable dual-relay smart control communicates wirelessly with and selects a six port remote antenna relay via the coaxial cable. The upgraded AS-603WL Smart Control Console with a black finish controls the AS-61WL weatherproof outdoor relay box with no control cable required. Select any one of three radios to connect or bypass the single amplifier I/O in the shack. Supporting one antenna connected to one radio at a time, manual or automatic selections of antenna and radio are confirmed with illuminated pushbuttons. Transceivers interfaced with optional cables provide frequency data for memorized automatic antenna selections. Interface cables are available for Elecraft, Icom, Kenwood and Yaesu transceivers which support frequency data for specific antenna selections by band segment. The AS-603AL also features an RS-232 serial port for PC controlled remote operation. The Hamplus AS-603WL Black system operates from 1.8 to 150 MHz and handles up to 3,000 watts PEP under 1.5:1 SWR. SO-239/UHF Female connectors on the back panel of the AS-603WL console include an In/Out pair to use one linear amplifier, wattmeter, or both, with all three radios! Click on HPY-AS-603WL-BK below to see more details! Finally, an intelligent remote antenna switch that knows what to do! Hamplus Automatic Remote Antenna Switch and Control Console Packages are ready for your multi-radio and multi-antenna station.
Not Yet Reviewed
$837.99
DX Engineering 6BTV 6-Band High Performance HF Vertical Antennas and OMNI-TILT® Mounting Systems
DX Engineering 6BTV 6-Band High Performance HF Vertical Antennas and OMNI-TILT® Mounting Systems are convenient and economical antenna installation packages that combine the time-tested Hustler antenna with our radial plate and our innovative tilt system! This can be your high performance HF ground mounted vertical antenna system. This DX Engineering Hustler 6BTV Package provides 80, 40, 30, 20, 15, and 10 meter band operation with: -- Dramatically improved transmit and receive signals -- Best possible signal pattern and performance boost with organized radial wire attachment system -- Simplified and long-lasting RF connections with proper connectors and cable -- Safe and easy tuning with our OMNI-TILT® mount - one person can walk the antenna up or down -- Professional grade stainless steel clamps and mounting hardware Included with each antenna package is our exclusive High Performance Hustler BTV Assembly and Installation Guide that will answer all your questions! You can read more right here, including the best way to install your vertical antenna system, the reasons for installing a radial system, and how to "Install Radial Wires Without Digging". Click "More Detail" below and then click the "Documentation" link. "More Details" includes the list of items included in this fantastic package. Make contacts beyond expectations! Operate with a versatile HF multi-band vertical antenna that performs to its full potential. Install a DX Engineering 6BTV 6-Band High Performance HF Vertical Antenna and OMNI-TILT® Mounting System.
( 4 )
$889.68
Begali Keys
Begali Keys represent the intersection of artistic design and mechanical achievement with the joy of operational perfection. Featuring over 30 stylistically functional iambic paddles and straight keys, each model has been intentionally hand-crafted with a goal – provide the operator with a uniquely perfect connection to their passion for telegraphy. Just as artists use an extremely specific instrument or tool as an extension of their skill, each Begali Key is designed to have unique mechanical and stylistic characteristics that serve the tastes of many different CW operators and telegraphy enthusiasts, and the eye of collectors. There is undoubtedly an ideal Begali model that will suit your code sending style and appeal to your appreciation of industrial art. Augmenting the artistry of these fine instruments of telegraphy, numerous Begali models are offered with different solid metal bases and bearing blocks with several spectacular finishes. A variety of finger piece materials, shapes and colors are offered to enhance the tactile response of the paddles and keys, as well as their appearance. Begali Keys have the weight to stay in place on the desk, and almost all but the straight keys include a rear panel 3.5mm TRS jack and patch cable for connection to your electronic keyer or transceiver keyer input. Begali Keys are considered to be the ultimate choice by CW operators and collectors around the world. They offer the pride in ownership of a uniquely stylish and functional tool of the trade and are revered as keepsakes to be passed down through generations of telegraphy enthusiasts.
( 29 )
$764.99
—
$823.99
Palstar AT2K 2000 Watt Antenna Tuners
Palstar AT2K 2000 Watt Antenna Tuners are the upgrade to the classic AT1500CV tuner, featuring a newly designed, smaller roller inductor, which allows the AT2K to tune 6 Meters. Newly designed capacitors with lower minimum capacitance improve high band performance, while maximum capacitance has been increased to 400pF for better low band performance. The AT2K features a 6 position antenna selector switch. In addition, the Peak/Peak Hold metering from the PM2000A has been incorporated into the AT2K. Forward power metering is in two ranges, 300 and 3,000 watts. Standing Wave Ratio measurements are displayed with this illuminated cross-needle meter. SWR is read directly from the meter face where the Forward and Reverse needles cross. The AT2K matches dipoles, center fed doublets, Verticals, end-fed wire, delta loops, beams, Windoms, Inverted Vees, and many more antenna types. With a chassis made of 11 ga. (.090 in. thick), iridite-treated aluminum, and a durable powdercoated finish on the front panel and top cover, you can have a tuner that will grace your shack for years to come. One eHam.net user wrote about the AT2K, "This is a tuner for life, buy one and you will not be disappointed." Palstar AT2K tuners feature: --Impedance range 20 to 1,500 ohms from 160 to 6 meters (assuming resistive load) --Low minimum custom variable capacitors, 15pF to 400pF at 4.5 kV --26 uH 5 kV ceramic body roller inductor with turns counter --Silver plated inductor wheel shaft and contact wheel Note: For additional information, please look at the files under the "Documentation" tab. Palstar AT2K 2000 Watt Antenna Tuners are destined to become a ham favorite from DX Engineering!
( 31 )
$795.99
QuietRadio Aziloop DF-72 Multi-Directional Receive Antenna System
The QuietRadio Aziloop DF-72 Multi-Directional Receive Antenna System is an innovative, low-noise solution for VLF to HF reception. This dual-mode, electronically rotatable HF receive antenna system features a primary frequency range of 20 kHz to 10 MHz, with coverage to 30 MHz at reduced directivity and sensitivity (determined by antenna size). Additionally, it can be fed with a single coaxial cable, eliminating the need for bulky antennas and rotators.
( 1 )
$779.99
Alpha Antenna 100W Base HF MagLoop Antennas
Alpha Antenna 100W Base HF MagLoop Antennas feature a 3ft. wide loop that covers frequencies from 40 -10 meters. They are remotely tuned and rated for 100W PEP SSB, 50W CW, and 25W digital, with each rating based on duty cycles. The magnetic loop antenna is a complete circuit, eliminating the need for radials or counterpoise. Additionally, they include a direct wire remote control for convenient operation.
( 1 )
$1,000.00
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles
Diex Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles offer high performance multi-band HF operations, and they are an excellent choice where there's not enough space for a full-size dipole or Yagi. Crafted with precision in Brazil using quality materials, these aluminum tubing antennas are designed to withstand tough environments assuring long-lasting, exceptional performance. They are packed partially assembled, saving valuable time and effort. Typically mounted on a rotating mast, these unique multi-band HF antennas provide high-band directionality depending upon installed height above ground. Given the nature of shortened low-band antennas with limited SWR bandwidth, these antennas feature the flexibility of physical adjustment to set the lowest SWR to a specific frequency. DIEX Antennas Multi-Band Trap Shortened Rigid Rotatable Dipoles power handling is 1500W PEP SSB, which is further limited if using an antenna tuner. NOTE: Diex Antennas recommends that a directional HF antenna should be mounted on a tower at a minimum height of 33 to 50 ft. (10 - 15 meters) above ground level and must be installed in the clear, away from power lines, trees, buildings or other towers and antennas.
( 2 )
$765.99