Availability
7 Results Found For "75 ohm coax"
DX Engineering Phased Array Quarter Wave Tuned Cables
DX Engineering Phased Array Quarter Wave Tuned Cables ensure optimum pattern control and gain from your phased antenna system. These cables are custom built to your array frequency, made with the highest quality waterproof PE jacketed, direct-burial RG-11/U 75-ohm low-loss foam coaxial cable and terminated with silver plated PL-259s. From the system phasing unit to each array element, these phasing feed-lines are one quarter wavelength long electrically, which differs from the free-space dimension by the velocity factor of the cable. The electrical dimensions of these cables are critical to system performance. These cables, manufactured to DX Engineering specifications, have a nominal velocity factor of 0.82, providing plenty of physical length for easy burial and routing from the base of the vertical to the center-mounted controller. DX Engineering Phased Array Quarter Wave Tuned Cables are custom built by DX Engineering. Each is hand crafted and electronically tuned to a specific HF frequency. Typically, they are tuned to the same frequency as the antenna array. After placing your order for DX Engineering Phased Array Quarter Wave Tuned Cables, please inform us of the order number and your array frequency for your tuned cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special order.
( 3 )
$899.99
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables
DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables are offered for your antenna system where the recommended quarter wave cables will be too short for your installation. There are cases where the phasing controller relay unit must be mounted away from the exact physical center of the array, such as when elevated verticals or elevated vertical dipoles are used. Three-quarter wavelength tuned cables are then required. The electrical dimensions of these cables are critical to system performance. They're made from the highest quality waterproof, direct bury 75-ohm RG-11/U gas-injected low-loss foam coaxial cable. Their length differs from a free-space dimension by the velocity factor of the specific cable type. These cables, manufactured to DX Engineering specifications, have a velocity factor of 0.84, providing the maximum physical length to allow for easy burial and routing from the feedpoint of the antenna to the controller relay unit. DX Engineering Four-Square Array Three-Quarter Wave Tuned Cables must be ordered for your desired frequency. These custom built tuned coaxial cable assemblies ordered from DX Engineering are hand crafted and electronically tuned to a specific HF frequency. Typically, customers request that they are tuned to the center or slightly below the center of their antenna array band, depending upon their planned modes of operation. After placing your order, please inform us of the desired frequency for your cables by e-mailing dxengineering@dxengineering.com or by calling 800-777-0703 or 330-572-3200. You may leave a message after business hours. Custom cable assembly orders will process after we receive your frequency information. Please contact DX Engineering Technical Support if additional assistance is needed. We will contact you if we have any questions about your special orders.
Not Yet Reviewed
$999.96
DX Engineering NCC-2 Receive Antenna Phasing Systems
Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!
( 19 )
$955.99
CG Antenna CG-3000 Remote Automatic Antenna Tuner
CG Antenna CG-3000 Remote Automatic Antenna Tuner is an affordable outdoor weatherproof tuner for long wires, verticals, dipoles and other Amateur, MARS or CAP operations between 1.6 to 30MHz. Like the well-known legacy SG-230, this tuner is primarily intended to feed wire antennas or monopoles. The antenna wire connects to the high voltage standoff insulator stud. A UHF female SO-239 connects the station coax and a ground stud may be used for a counterpoise or an earth ground. The tuner has an impedance range of 12 to 1000 ohms with a maximum power handling of 200 watts PEP in SSB mode and 40 watts for FT8 operation. The minimum required antenna length is 8 ft. (2.5m) for frequencies above 6 MHz, and at least 26 ft. (8m) for 1.8 MHz and up. With a small fiberglass pole and some wire, a good all-band antenna can be constructed within minutes. The CG-3000 Remote Automatic Antenna Tuner is automatically activated with a low power carrier. Low SWR tuning results are stored in non-volatile memory and new tuning attempts on similar frequencies are amazingly fast. The CG-3000 uses a Pi network design which has the advantage (as compared to L networks) of providing low-pass filtering to reduce spurious emissions. The tuner has a 4-pin connector on the bottom panel for the included 16 ft. Control Cable to supply the required 13.8 VDC at 2A (power supply not included). An additional control cable is not required. The solid plastic clamshell case protects the tuner in all-weather outdoor use. Attached brackets and 2.16 in. (55mm) width U-bolts and hardware are included. An optional CG Antennas CG-CTU Control Unit offers an ON/OFF power switch and a TUNE button, both with LED indicators and a 32.8 ft. (10M) control cable. The CG-CTU includes a 4-pin tuner interface and power connection for Icom transceivers. The CG-3000/CG-CTU combination works with all other transceivers with the included connector cable that serves as a power supply DC cable. CG Antennas CG-3000 Remote Automatic Antenna Tuner Specifications: Supported Bands: 160m, 80m, 40m, 30m, 20m, 17m, 15m, 12m, 10m. Max. Power [W]: 200 W Impedance Range: 12- 1000 Ohm Enclosure: Black waterproof plastic Supply Voltage: 13.8 VDC via included 16.5 ft. (5m) Control Cable Dimensions (WHD): 9.450 x 14.370 x 2.953 in. (240 x 365 x 75 mm) Weight: 2.98 lbs. (1.352 kg)
Not Yet Reviewed
$784.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 4 )
$999.96
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units
DX Engineering PS-3B PRO-STACK Three Antenna Phasing Units offer the ultimate performance for combining three identical Yagi or Log Periodic directional antennas and may be used for vertical antennas in a phased array that cover any band, from 160 through 10 meters. Pro-Stack frequency independent broadband phasing devices operate optimally with three properly spaced mono-band antennas, but can be used with three identical stacked multi-band beam antennas, for pattern and null steering that wins contests and snags the rarest DX! Signals arrive at your antenna system from different azimuth directions and different elevation angles. Adding a stacking phasing system to a rotational array adds the ability to steer the pattern of the antenna array in two planes, azimuth and elevation, and to move the major lobe and nulls. The greatest advantage of Pro-Stack arrays is the ability to move harmful pattern nulls away from signal arrival angles. While gain makes a marginal improvement, moving a 20 to 40 dB null can be a phenomenal change, so the Pro-Stack can make the difference between a barely readable and a strong signal, providing the performance edge needed to work rare DX - and win contests. DXE-PS-3B Pro-Stack Phasing Units are 50 ohm relay systems that handle up to 5 kW. A separate user-supplied automated controller or the optional DX Engineering DXE-EC-PS3 Control Console for these 12-position rotary switch selections: - Three antenna ports in phase, default with no power to control console. - Antenna port 1 only - Antenna port 2 only - Antenna port 3 only - Port 2 out of phase, Port 3 in phase - Port 1 out of phase, Port 3 in phase - Port 1 out of phase, Port 2 in phase - Ports 2 and 3 in phase - Ports 1 and 3 in phase - Ports 1 and 2 in phase - Ports 1 and 2 in phase, Port 3 out of phase - Ports 1 and 3 in phase, Port 2 out of phase - Port 1 out of phase, Ports 2 and 3 in phase These PRO-STACK units may also be used for other applications requiring these feedline selections. To ensure lowest SWR, impedance matching automatically changes when any antenna is disabled. By switching between antennas at different heights above ground and/or changing the phase relationship between multiple antennas. The old standard system in stacks was to activate or disable specific antennas in the stack to change pattern. However, with the Pro-Stack system, gain remains higher when all antennas are driven and phase is changed, plus this system allows phase inversion as well as the ability to switch any single antenna out of the array. DXE-PS-3B Broadband Phasing Units provide the greatest flexibility for three identical antennas. This relay unit contains a broad-bandwidth high-power 2:1 impedance matching transformer. This eliminates common requirements of using mixtures of 75 ohm and 50 ohm phasing or delay cables for impedance matching. Feedlines to each antenna from the relay unit must be the same cable of the same length and match the antenna impedance. DXE-PS-3B Pro-Stack Broadband Three Antenna Phasing Units feature: - Power Handling up to 5 kW - Broad band coverage on 160-10 meters - RF Shielded Weatherproof Housing - unique protection - DXE-PS-3B has High-RF tolerant, silver - PTFE UHF connectors - DXE-PS-3BDIN has Amphenol Connex 7/16 DIN Panel Connectors - DXE-PS-3BN-P are made with high-quality silver-PTFE Type N female connectors - Proven high current DX Engineering RF Relays - Safe 12 volt dc relay operation - MOV surge protection on control lines - RoHS compliant assembly Get a DX Engineering PS-3B PRO-STACK Three Antenna Phasing System for your winning antenna array.
Not Yet Reviewed
$895.99
—
$999.99
DX Engineering DVA Dual Vertical Array Systems
DX Engineering DVA Dual Vertical Array Systems are advanced phasing systems that have set a new standard for array performance with two ground-mounted verticals. Dual Vertical Array Systems include a compact DVA Phasing Relay Unit made specifically for an individual HF band and an EC-DVA Directional Control Console. DX Engineering Dual Vertical Arrays produce two opposite enhanced End-Fire Cardioid patterns and one Broadside-Omni pattern. Heavy-duty components handle over 2 kW continuous RF power for enhanced performance at low SWR over a wide bandwidth. The Dual Vertical Array end-fire directional patterns achieve a real front-to-back over 20 dB with typical array forward gain up to 3 dB over a single vertical. The greatest advantage of a Dual Vertical Array is that a tower and rotator are not required, as with a Yagi antenna. Especially for 160, 80, and 40, and even on the other HF bands, a Dual Vertical Array is mechanically simpler and safer. Here is a financially practical directional antenna that is much easier to install! These are great directional antenna systems for temporary and Field Day operation, as well as for permanent builds, because they ARE so much easier to install than a beam! If you are dissatisfied with your present system, are ready for an upgrade, or just need to get out of the tower game, the DX Engineering DVA is your answer! Refurbish an existing antenna system, equip your temporary array, or build a new phased array with a DVA. It's all on the ground, safe and simple: DX Engineering Dual Vertical Arrays offer a better way to enjoy a high-performance mono-band directional antenna. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 4 )
$775.98