Availability
21 Results Found For "Tinned braid"
DX Engineering Tinned Copper Braid Assemblies
DX Engineering Tinned Copper Braid Assemblies are typically used for the proper grounding of individual pieces of electrical or electronic equipment to a common grounding bus, such as a copper strap or a thicker bus bar. DX Engineering tinned copper braid assemblies are used for industrial, commercial, and broadcasting applications inside of electrical racks, for the connection of sub-assemblies to a metal chassis or grounding point, and for any special application where a high-quality tinned copper braid assembly is required. Our assemblies are made with top-quality tinned copper braid of various widths and lengths, and most are terminated with machine-crimped and hand-soldered terminals. Some assemblies feature heat shrink tubing over the connections for strain relief and longevity. Be confident with your equipment and system grounding with the best--DX Engineering Tinned Copper Braid Assemblies.
( 95 )
$14.25
—
$31.99
DX Engineering Tinned Copper Braid
DX Engineering tinned copper braid is available in five widths and is perfect for grounding applications. It's sold by the foot to accommodate almost any project. Contact your DX Engineering sales representative to discuss your needs if long, continuous lengths are required.
( 40 )
$0.85
—
$2.25
DX Engineering UNUN to Vertical Antenna Feedpoint Connection Kits
DX Engineering UNUN to Vertical Antenna Feedpoint Connection Kits consist of two tinned copper braid straps for a connection between a DX Engineering 4:1 high power UNUN and the ground radial systems and feedpoint of a vertical antenna. These straps are the correct length to allow for short, low inductance connections, and flexible to allow for the use of a tilt base with the antenna. Included with the UN-43-R, both straps measure 10 in. long, 9 in. from center to center of the preformed 1/4 in. holes, 1 in. wide, and 0.045 in. thick. The width and thickness may vary slightly as the flexible braid is stretched or compressed. DX Engineering UNUN to Vertical Antenna Feedpoint Connection Kits are the perfect choice when adding an UNUN to your antenna system.
( 2 )
$11.99
DX Engineering Exhaust Grounding Kits
Eliminate stubborn noise in your mobile installation with DX Engineering Exhaust Grounding Kits. Many modern vehicles have individual injectors and spark plug coils for each cylinder. These units can create substantial pulses on the vehicle wiring against the ground system. Engine blocks often have a poor ground, so anything attached to them can become a radiator. The exhaust pipe is directly bolted to the engine and can be excited just like an antenna, radiating the pulsing noise. By using one of our exhaust grounding kits, you can eliminate noise from your mobile installation. All hardware in these kits is made from high quality stainless steel. Each kit includes: * Exhaust saddle clamp * 14 in. long x 0.75 in. wide x 0.125 in. thick tinned copper braid * 3/8 x 1 in. bolt * 3/8 nut * Three 3/8 external tooth washers * 3/8 flat washer * 3/8 split washer
( 5 )
$31.99
—
$34.99
DX Engineering Station Accessory Packages
DX Engineering Station Accessory Packages take the guesswork out of ham radio shopping and help you get going and get on the air! We've assembled specialized accessory packages to make it easy for the beginner, as well as the more experienced hams trying a new system or a new facet of our great hobby. You've got a good-performing station and DX Engineering has the equipment and accessories necessary to make it even better! CLICK or TAP on the title of a listed item for an overview - a complete description, Kit Contents, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation.
Not Yet Reviewed
$515.42
DX Engineering 400MAX Low-Loss 50-ohm Bulk Coaxial Cable
DX Engineering 400MAX is premium, low-loss, 50-ohm bulk cable with a special Type III-A, UV-resistant polyethylene jacket that is waterproof; ideal for outdoor applications, particularly direct-bury. With its larger 10 AWG stranded copper center conductor, 400MAX is specially suited for high-power amateur stations, providing a lower loss solution for long cable runs at any legal power level. The high-quality construction continues with a gas-injected foam polyethylene dielectric, followed by the highest level of shielding with bonded aluminum tape covered by a tinned copper shield braid. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX Low-Loss 50-ohm Bulk Coaxial Cable accepts standard PL-259 or N connectors. Note: For additional product information, please look at the files under the "Documentation" tab.
( 92 )
$1.54
—
$1,539.99
DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies
Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849
( 324 )
$40.99
—
$334.99
DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies
DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!
( 33 )
$41.99
—
$182.99
Clearance
Georgia Copper Flexible Copper Grounding Straps
Georgia Copper Flexible Copper Straps are solid and bendable metal straps that are used to build low-inductance, high performance grounding systems. The use of these copper straps provides the best grounding systems because they have greater surface area and lower inductance per foot than the equivalent cross-section of wire. Hams find all sorts of uses for copper straps, for superior antenna feedpoint connections as well as creating a bus for grounding. Equipment racks may be bonded to ground using copper straps. Don't rely on the rack frame to provide bonding. Tie all of the power supplies, tuners, racked amplifiers, and other equipment together with low-resistance copper. Especially useful for any application outdoors and for use directly in or near soils, flexible solid copper straps will maintain a proper, low-impedance connection long after small-gauge wires and tinned copper braids have weathered and disintegrated. Copper straps are specified by communications system designers and are used extensively for above-ground and underground connections to radiators, tower and ground rods for commercial equipment rooms, sheds, and tower installations. Professional communications engineers know the value of systems that employ copper straps. They are available in various widths and at a thickness to suite your application. If you are using wire or braid at feedpoint connections or to provide grounding, equipment bonding or other critical connections for your Amateur Radio station, consider upgrading to long-lasting and solid Georgia Copper Flexible Copper Straps from DX Engineering!
( 25 )
$155.99
$52.99
—
$1,620.99
DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies
What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849
( 8 )
$55.99
—
$573.70
Times Microwave Systems® Mid-span Coaxial Grounding Kits
Times Microwave Systems Mid-span Coaxial Grounding Kits let you ground the coaxial shield to any convenient location with a ground lug. This includes most grounding clamps, plates and fixtures. For towers, an additional tower leg clamp is usually required. After stripping the outer jacket with a mid-span stripping tool, a pre-formed metal strap is applied to the braid/shield and tightened down. This strap is then electrically and mechanically connected to the ground source with a ground lead assembly, providing an excellent ground for the shield. These mid-span shield-grounding kits include: (1) Pre-formed tinned copper ground strap (1) Ground lead assembly (2) 1/4 in. brass lock-washers (2) 1/4 in. brass nuts (1) Roll 2-1/2 in. x 24 in. (610mm) butyl mastic (1) Roll 3/4 in. x 20 ft. (6.1m) PVC tape (1) Heat shrink tube (1) Field-crimp 3/8 in. 2-hole lug (2) 3/8 in. x 1-1/4 in. slotted bolts (2) 3/8 in. lock-washers (2) 3/8 in. nuts (2) 3/8 in. flat-washers (1) Detailed assembly instructions Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Their included weatherproofing materials provide long-lasting environmental protection to help maintain a reliable ground for your coax. Shop DX Engineering for Times Microwave Systems Mid-span Coaxial Grounding Kits! LMR® is a registered trademark of Times Microwave Systems.
( 4 )
$34.65
—
$45.99
DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies
DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies are very flexible, solid dielectric, braided shield cable intended for RF connections to SO-239 and BNC equipment and antennas. These assemblies are suitable for moderate-power applications where flexibility is a key consideration. NOTE: These premade cables come with either high quality, silver plated 83-1SP PL-259 or silver plated BNC Male connectors installed at each end of the DXE-58AU cable, for use on any equipment with SO-239 or BNC Female connectors. Slightly smaller than RG-8X cable, DX Engineering RG-58A/U Coaxial Cable Assemblies are made from our new-process DXE-58AU solid dielectric cable. Featuring a stranded tinned copper center conductor, a braided tinned copper shield and a standard Type I PVC jacket, our 58AU cable assemblies are intended for low to moderate power, test and mobile applications where short runs and flexibility are required. DX Engineering RG-58AU offers easy handling characteristics and good shielding. Plus, this solid dielectric cannot gather moisture and has longer viability than old RG-58 foam cables. INFO: Type-I PVC is not intended for permanent installation in outdoor locations where sun exposure is expected. This cable can last well over 10 years if it is protected from UV sunlight. Our RG-58AU Coaxial Cable Assemblies come complete with high-quality silver-plated Delrin-dielectric PL-259 or BNC male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. Their center conductors are hand soldered and inspected. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. When you are looking for lightweight and flexible pre-assembled cable assemblies and want a high-quality, reliable product, look no further than our own DX Engineering RG-58A/U 52-ohm Low-Loss Coaxial Cable Assemblies.
( 1 )
$34.99
—
$55.99
Clearance
Georgia Copper Flexible Ground Strap Jumpers
Georgia Copper Flexible Ground Strap Jumpers are excellent for low impedance outdoor grounding and HF antenna feedpoint and radial system connections. Even weathered to a dull patina, copper strap does not lose its low impedance advantages over wire or cables, for DC and AC through HF and VHF. Plus, flexible copper strap is far superior to tinned copper braid, which holds moisture and disintegrates which causes a undesirable increase in connection impedance over a relatively short time. Flexible SOLID Copper Strap Jumpers come in pre-cut lengths at 1 in. or 3/4 in. widths and 0.022 in. thickness, punched with 0.280 in. holes at each end, to accommodate 1/4 in. bolts. They're available in two-packs at six different lengths, 6 in., 12 in., 24 in., 36 in., 48 in., 72 in. and also in a variety pack that contains one piece of all six lengths. Order and use any of these specific length straps for your project. Or, use your tin snips and your imagination to make all types of low impedance connections for surge protection grounding boxes and panels, protectors, equipment racks, vertical antenna feedpoints, radial system connections and antenna feedpoint connections from a bolt terminal balun to the driven elements. This pre-cut copper strap may also be used as a shack ground bus or for the bus bar connection to the station ground rod or rods. Hobbyists and Electricians order extra copper straps to have on hand and be ready for those grounding and antenna connection projects that come up. Georgia Copper Ground Strap Jumpers are here at DX Engineering, ready for your needs.
( 10 )
$114.99
$21.99
—
$91.99
DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies
DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are available in several useful lengths, terminated with DX Engineering Next Generation PL-259 connectors; ultra-high quality all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. DX Engineering Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that fully engage even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and adhesive heat-shrink weather-sealed for the ultimate in service longevity Times Microwave Coaxial Cables are recognized as superior RF cable products. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center conductor, a gas foam polyethylene dielectric, and a rubber-like black thermoplastic elastomer jacket designed for repeated bending. LMR®'s RF shielding is typically 50 dB greater than off-brand single braided shield coax. LMR® UltraFlex copper braid and multi-ply bonded foil outer conductor shields provide greater than 90dB shielding. That is better than 180 dB isolation between two adjacent LMR® cables. DX Engineering Times Microwave LMR® UHF Male Coaxial Cable Assemblies are an excellent choice for a variety of indoor, mobile, portable, and outdoor applications.
( 1 )
$42.99
—
$196.99
Heil Sound Heil Wire Microphone Cable
Heil Sound Heilwire Microphone Cable is a specially-designed cable ideal for connecting microphones, foot switches, keyer paddles, and other audio, data or control devices. Heilwire features two 18-gauge wires inside a 100% coverage silver-plated braid shield, plus two 18-gauge wires external to the braid, for PTT or other control purposes. This design reduces capacitive coupling between the control lines and the sensitive AC audio signals residing inside the shield, resulting in significant reduction of the possibility of hum pickup, PTT pulses or RFI. Heilwire has an outer jacket made with extra flexible PVC and has a specified outer diameter of 1/4 in. to fit perfectly inside Heil Sound connectors. Heilwire Microphone Cable is great for many different types of audio and switching connectors and applications. For making connections to microphones and other devices, Heil Sound's exclusive Heilwire is the best choice. Get some today from DX Engineering.
( 7 )
$20.00
—
$70.00
Times Microwave Systems® Bulk Coaxial Cables
Times Microwave Systems Bulk Coaxial Cables are recognized as superior RF cable products. The standard Times Microwave LMR® is a UV-resistant polyethylene jacketed cable designed for 20-year service in outdoor use. Depending upon size, LMR® cable has a solid copper or copper clad solid aluminum center conductor. Their bending and handling characteristics are significantly better than air-dielectric and corrugated hard line cables. LMR-DB® cable has a waterproofing compound to prevent moisture intrusion after a minor abrasion. Times Microwave Systems EZ Series and TC Series connectors are suitable for use on standard LMR® and LMR-DB® cables. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center and a rubber jacket (black thermoplastic elastomer) designed for repeated bending. Times Microwave TC Series crimp connectors are designed for use on LMR® UltraFlex cables. LMR®'s RF shielding is typically 50 dB greater than standard coax. The copper shield and multi-ply bonded foil outer conductor is rated conservatively at greater than 90 dB. That's better than 180 dB isolation between two adjacent cables. A wide variety of connectors are available for LMR cables, including all common interface types, reverse polarity, and a choice of solder or non-solder center pins. Most LMR connectors employ crimped outer attachment using standard hex-crimp methods. Times Microwave Systems is a premier supplier of coaxial cable products worldwide. Only Times offers a range of products specifically developed to perform as needed in the most diverse range of environments. Times Microwave Systems has over 60 years of experience in building the highest-quality cables. Order LMR® coaxial cables from DX Engineering and put Times Microwave Systems Bulk Coaxial Cables to work for you! LMR® is a registered trademark of Times Microwave Systems.
( 106 )
$0.90
—
$1,229.99
DX Engineering LMR400UF Ultra-Flex Coaxial Cable Assemblies
DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies handle twice the power at half the loss with the same bending capabilities of smaller diameter coaxial cables. UltraFlex Cable Assemblies are perfect for interconnecting high and low power HF and VHF equipment. Times Microwave LMR® 400UF UltraFlex cable has a stranded bare copper center, foam polyethylene dielectric and a pliable rubber jacket (black thermoplastic elastomer) designed for bending. DX Engineering LMR400UF UltraFlex DX Series PL-259 Coaxial Cable Assemblies are terminated at each end with our custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity checked and evaluated with extremely high voltage, then heat-shrink weather-sealed for ultimate longevity. You will not find this level of cable assembly quality anywhere else! Terminated with DX Engineering Next Generation PL-259 connectors, these cable assemblies are intended for use to 170 MHz. An exceptionally flexible, low-loss coaxial jumper for high power Amateur or commercial HF or VHF use – order DX Engineering LMR400UF UltraFlex Coaxial Cable Assemblies.
( 30 )
$54.19
—
$289.99
DX Engineering RG-58A/U 52-ohm Bulk Coaxial Cable
DX Engineering RG-58A/U 52-ohm Bulk Coaxial Cable is a highly flexible, 52 ohm feedline with a black PVC jacket, which is ideal for all indoor and some outdoor applications where UV exposure is not an issue. Specially suited for low to medium-power amateur stations, RG-58A/U also provides an ultra-flexible cable for coaxial jumpers. DX Engineering RG-58A/U features a low-density polyethylene dielectric and uses PL-259 or 2-piece N connectors. Both connector types must be used with reducing adapters that fit RG-58 cable.
( 17 )
$0.55
Consolidated Wire Coaxial Cable Assemblies
Consolidated Wire Coaxial Cable Assemblies are low loss coaxial cable assemblies engineered for specialized RF device interconnections up to 6 GHz. Crafted with precision, these lightweight cable assemblies feature a PTFE dielectric insulating material. The FEP (Fluorinated Ethylene Propylene) jacket on the RG316 series and PVC (Polyvinyl Chlorine) jacket on the RG174 cables offers outstanding UV and chemical resistance to ensure durability in challenging environments. The wide operational temperature range, flexibility and quality BNC or SMA connectors make these cable assemblies the perfect choice for your next project.
( 8 )
$9.99
—
$17.99
Sierra Radio Systems Coax Cables
Sierra Radio Systems Coax Cables are pre-terminated, 6 foot runs of LMR-195 with a BNC Male on one end and a PL-259 on the other. The cable is ready to use with the Sierra Radio Systems Coax Switch module.
Not Yet Reviewed
$29.00
Hustler Antenna Mount Cables
Hustler Antenna Mount Cables are designed to connect mobile coaxial cable feed to a ball mount. They are built from top quality RG-58 coaxial cable. These cables have a PL-259 connector on one end and a shield-connection collar and end ring with lugs on the other. These are very well constructed cables that are neat in appearance. Do you need a new cable for your mobile antenna ball mount? Order Hustler Antenna Mount Cables from DX Engineering!
( 3 )
$19.99