Selected Filters


Availability


61 Results Found For "75 ohm coax"

Part Groups

Results 1 - 24 of 61

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable

DX Engineering RG-6U 75-ohm Flooded Quad Shield Coaxial Cable is our top-of-the-line, direct-bury RG-6. It has low RF signal loss and provides greater protection against electromagnetic interference. Available cut-to-length by-the-foot or in 1,000 ft. spools, this is the best ultra-high quality RG-6/U self-healing quad-shield cable solution. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. DXE-RG-6UFQ cable is ideal for many receiving applications including active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution and satellite radio installations such as Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up through microwave frequencies of satellite radio systems! Our RG-6 flooded quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding. The waterproof UV protected black jacket is made with a tough and flexible polyethylene (PE). This cable is infused with a flooding compound that provides a permanent barrier to moisture and is self-healing to minor cuts. The nominal impedance of DXE-RG-6UFQ cable is 75 ohms with a nominal Velocity Factor of 82% (VF = 0.82). The minimum bend radius is 2.500 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? DX Engineering RG-6U 75-ohm Flooded Quad-Shield Coaxial Cable is absolutely the best RG-6 quad-shield cable available and it is RoHS compliant! Check these super low attenuation figures! 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? If so, then order the new benchmark in RG-6 cable: DX Engineering RG-6U 75-ohm Flooded Quad Shield Coax. Your efforts will be rewarded with the results that you expect, using the best cable from DX Engineering.

4.78 out of 5 stars ( 9 )

$0.37

—

$255.99

DX Engineering 75 ohm Coaxial Lightning Surge Protectors

DX Engineering 75 ohm Coaxial Lightning Surge Protectors feature a unique design that is impedance-matched to 75 ohms and are virtually transparent to all analog or digital bi-directional signals from DC to 1.0 GHz. Manufactured by Tii Network Technologies for DX Engineering, their patented proprietary coaxial gas tube surge protectors are equipped with an integral failshort mechanism for a power-cross condition, which shunts both the coaxial cables' center conductor and sheath for a common path to ground. The dc breakdown voltage of the protector provides superior protection against transient surges, and yet is compatible with network-powered applications. They may also be used in 75-ohm receive systems up to 1.0 GHz. The protection element is designed to reset after each over-voltage event and the metallic housing of the coaxial lightning surge protectors provides necessary EMI shielding. When properly connected, DX Engineering Coaxial Lightning Surge Protectors are environmentally sealed (15 psi) to prevent the ingress of moisture and humidity encountered in broadband pedestals, vaults and stand-alone receive antenna applications. Full 360 degree Type F connectors provide superior RF performance and tighter connections.

5.0 out of 5 stars ( 9 )

$39.99

DX Engineering RG-6/U 75-ohm Quad-Shield Coax Cable Assemblies

Our new DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies are constructed from our own premium DX Engineering brand RG-6/U 75 ohm cable and superior quality weather-sealed nickel-plated compression F connectors. Their best-in-class design reduces loss and provides greater protection against electromagnetic interference. Available in specific lengths between 3 ft. and 200 ft., these pre-assembled cables with F connectors are your most convenient ultra-high quality RG-6/U cable solution. These RG-6/U cable assemblies are ideal for many applications such as active or passive HF Amateur Radio receive antenna systems, magnetic loop antennas, Beverage antennas, over the air TV reception, FM broadcast reception, CATV systems, raw video distribution and satellite radio installations like Sirius/XM. In fact, their low-loss characteristics are excellent up to the microwave frequencies that Satellite Radio systems employ! Our RG-6/U cable assemblies have gas-injected polyethylene foam dielectric for flexibility and moisture resistance. Their 18 AWG center conductor is copper-clad steel and is durable in the extreme. They have two foil shields plus two high-density aluminum braids for ultimate four-layer RF shielding. Their UV protected black exterior jacket is tough PVC (polyvinyl chloride). DX Engineering RG-6/U cable impedance is 75 ohms with an 83 percent velocity factor and have a minimum bend radius of 2.50 in. This is absolutely the best RG-6/U cable available and it's RoHS compliant! Look at these attenuation figures per 100 ft.: 5 MHz: 0.6 dB 30 MHz: 1.1 dB 55 MHz: 1.6 dB Are you installing or upgrading any receiving antenna or video distribution system that uses RG-6/U cable? If so, then these exceptional DX Engineering RG-6/U 75-ohm Quad-Shield Coaxial Cable Assemblies will make your installation easier and your results so much better!

5.0 out of 5 stars ( 13 )

$28.99

—

$86.99

DX Engineering RG-11/U 75-ohm Bulk Coaxial Cable

DX Engineering RG-11/U 75-ohm Bulk Coaxial Cable is a low-loss, high-power 75-ohm feedline with a premium-grade, waterproof polyethylene jacket. Manufactured specially for DX Engineering, the 11U jacket is UV-resistant and, due to its durability, works great in direct-bury applications. This RG-11/U cable is ideal for impedance-matching phasing cables for arrays from HF Four Squares to VHF applications. The 82 percent velocity of propagation provides the longer cables necessary to reach from the center-of -the-array mounted Four Square controller to each element at the corners of the array. DX Engineering 11U cable is easily terminated with any of the solder type and crimp type PL-259 (UHF male) and N connectors which are designed for installation on 0.405 in. OD, RG-8U sized cables. You are in the market for a 75-ohm cable that provides high reliability and long life. Choose DX Engineering RG-11/U 75-ohm Bulk Coaxial Cable.

4.75 out of 5 stars ( 8 )

$1.49

DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable

DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable is our regular RG-6U with a Type II PVC jacket, low loss and greater protection against electromagnetic interference. Available cut to length or in 1,000 ft. spools; this is a high-quality standard RG-6U quad-shield cable. This cable may be terminated in the field with black EX6XL Type-F Universal Compression Connectors, also available from DX Engineering. (Please Note: Also available is our waterproof direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ-CTL and DXE-RG6UFQ-1000.) DXE-RG-6UQ cable is ideal for many applications, such as active or passive HF Amateur Radio and SWL receive antenna arrays and systems, LW and MW magnetic loop antennas, Beverage antennas, over-the-air TV, AM and FM broadcast reception, CATV systems and video distribution as well as satellite radio installations like Sirius/XM. In fact, the low-loss characteristic of our RG-6 cable is excellent for digital audio up to the microwave frequencies that Satellite Radio systems employ! Our RG-6 quad shield cable has gas-injected polyethylene foam dielectric for the lowest loss and maximum moisture resistance. With an 18 AWG copper-clad steel center conductor it is extremely strong and durable. Two foil shields plus two high-density aluminum braids provide ultimate four-layer RF shielding and the UV protected black jacket is made with a tough, but very flexible, PVC. The nominal impedance of DXE-RG-6UQ cable is 75 ohms, and it has a nominal Velocity Factor of 82%. The minimum bend radius of this cable is 2.50 in. Beware of cheaply made cable with unknown impedance and loss characteristics. If some other cable is substantially less expensive, that should tell you something, right? Please Note: Also available is our direct-bury PE jacket RG-6 version: search 75-ohm Flooded Quad Shield, DXE-RG6UFQ and DXE-RG6UFQ-1000. This DX Engineering RG-6UQ 75-ohm Standard Quad-Shield Coaxial Cable is a Type-II PVC jacket RG-6 quad-shield cable that is RoHS compliant. Check out these low attenuation figures: 5 MHz: 0.6 dB/100 ft. 30 MHz: 1.1 dB/100 ft. 55 MHz: 1.6 dB/100 ft. Losses at 1.8 MHz are virtually insignificant over several hundreds of feet of this coaxial cable. It can be used for low band receive antennas and arrays without the complications of using a preamp at the antenna. Are you installing or upgrading a Low Band receiving antenna or a CATV or satellite video distribution system that uses RG-6/U Quad cable? Order DX Engineering RG-6U 75-ohm Standard Quad-Shield Coaxial Cable.

5.0 out of 5 stars ( 1 )

$0.39

—

$219.99

Clearance

DX Engineering F6 75-ohm Coaxial Cable Assemblies

DX Engineering F6 75-ohm Coaxial Cable Assemblies are intended to be used for HF receive antenna systems as well as for cable or satellite TV system use. They are made with a high-quality, 75-ohm, direct-bury, "flooded" F6-type coax and watertight Snap-N-Seal F connectors. Flooded-style feedline, infused with a waterproof compound, have the distinct advantage of automatically sealing small accidental cuts or lacerations in the cable jacket. Plus, the flooding compound works perfectly with the Snap-N-Seal connector's O-rings to provide a reliable, environmentally sealed connection that prevents shield contamination, with no external waterproofing requirement. These low-loss cable assemblies feature a waterproof polyethylene jacket, dual shields, and connectors that are installed with a unique 360 degree radial compression system. A superior RF integrity of over -95 dB external signal rejection means that DX Engineering F6 75-ohm Coaxial Cable Assemblies are your best choice for any high performance system installation.

Not Yet Reviewed

$28.99

—

$29.99


$20.29

—

$20.99

DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coax Assemblies

Our patented* revolutionary new PL-259 connector and our premium, low-loss 400MAX coaxial cable are designed to make the new DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best cable assemblies available for simplex HF, VHF and UHF applications. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX DX Series low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 DX Series Coaxial Cable Assemblies are terminated at each end with our new, custom-designed, silver-plated brass DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our new 400MAX DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are now available, only from DX Engineering! *U.S. Patent D745849

4.95 out of 5 stars ( 324 )

$144.99

DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our premium flexible DXE-8X coaxial cable were designed to make the new DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8X cable assemblies available for HF applications. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are made from our new-process low-loss, gas injected foam dielectric cable. Featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket, good for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, this is the new type of foam that cannot gather moisture and has lower loss than old RG-8X foam cables. DX Engineering RG-8X PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These new, ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849

4.96 out of 5 stars ( 545 )

$78.99

DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our premium 213U coaxial cable were designed to make the new DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coax Assemblies the best 213/U cable assemblies available for virtually every HF antenna application. DX Engineering 213U is a high-grade standard coaxial cable type, which features a very rugged, highly UV-resistant, non-contaminating Type II-A PVC jacket. These cable assemblies are ideal for all outdoor feedline applications, commonly used for HF and direct-bury installations. With heavy 12.5 AWG stranded copper center conductor, RG-213U PL-259 cable assemblies are perfectly suited for long cable connections to antennas from HF equipment running at very low to high power levels. Our DXE-213U cable features a solid polyethylene dielectric that cannot absorb moisture and it withstands constant movement and flexing on tower mounted rotatable and directional beam antennas. DXE-213U is used at contest station K3LR for installation at the tower top as "rotator loop" coax for HF and VHF. It has excellent shielding with minimum 96 percent coverage copper braid. Regarded in the industry as the right choice for a high quality HF feedline, our 213U Coaxial Cable is custom made for DX Engineering to provide the performance and longevity you expect. DX Engineering RG-213U PL-259 DX Series Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These patented* Next Generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 213U DX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-213U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our Next Generation PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849

4.98 out of 5 stars ( 185 )

$149.99

DX Engineering 400MAX Type N Low-Loss 50-ohm Coax Assemblies

DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies offer the lowest possible loss at VHF and UHF frequencies. Used by communications professionals through 2,400 MHz and above, N-Type connectors have low insertion loss and maintain 50 Ohm impedance, for installations where every tenth of a dB counts! DX Engineering 400MAX coax features a tough, waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for simplex outdoor feedline applications including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX low-loss assemblies are perfectly suited for long cable runs and low or high power level operations. Our 400MAX coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95 percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. B) Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. DXE-400MAX is not recommended for use in in a VHF/UHF duplex repeater applications or for a beam antenna rotator loop. Our 400MAX DN Series cable assembly N-Type connectors feature machine crimped shields and centers, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate in-service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering 400MAX Type N Low-Loss 50-ohm Coaxial Cable Assemblies are now available, only from DX Engineering!

5.0 out of 5 stars ( 33 )

$148.99

DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coax Cable Assemblies

Our patented* revolutionary new PL-259 connector and our high quality, low-loss RG-8U coaxial cable were designed to make the new, extra-flexible DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies the best RG-8/U cable assemblies available for all HF, VHF and UHF applications. DX Engineering 8U coax features a super-flexible jacket made with UV-resistant, Type I PVC jacket which is great for all indoor and above-ground outdoor applications. With a large 11 AWG stranded copper center conductor, our 8U DX Series low-loss assemblies are well suited for short interconnections as well as long cable runs in low or high power operations. Our 8U coax cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has excellent shielding with minimum 95 percent coverage copper braid. DX Engineering 8U is a new-age cable that far surpasses the capabilities of the moisture collecting foam RG-8/U of 35 years ago. Now regarded in the industry as a top quality low-loss feedline, our 8U Coaxial Cable is custom made for DX Engineering to provide the highest performance with extraordinary flexibility. DX Engineering RG-8U PL-259 Low-Loss Coaxial Cable Assemblies are terminated with our new, custom-designed, silver-plated brass-bodied DX Engineering PL-259 (UHF male) connectors. These next generation PL-259 connectors feature: -Full diameter, full length soldered center pins that snugly fit even worn SO-239s -Spacious center pin inside diameter that accepts large conductors and allows generous solder flow -Deep, double knurled threaded shells for secure finger tightening These new, ultra-high quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Our 8UDX Series cable assembly PL-259 center pins are hand soldered by trained assembly techs to assure a proper connection. These special PL-259 cable assemblies also feature machine crimped shields, with 360 degrees of complete mechanical and electrical contact for maximum reliability. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! DX Engineering RG-8U PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies with our new PL-259 connectors are available only from DX Engineering! *U.S. Patent D745849

4.93 out of 5 stars ( 113 )

$132.99

DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies

DX Engineering RG-8X PL-259 Low-Loss 50-ohm RF Choke Coaxial Cable Assemblies feature our patented* revolutionary PL-259 connector and our premium flexible DXE-8X coaxial cable. They were designed to make the best RG-8X cable assemblies available for HF applications. Adding fifteen Mix-31 ferrite beads makes them even better! The ferrite beads provide RF choking to reduce RFI and improve current balance on antennas. These assemblies are made with low-loss, gas injected foam dielectric DXE-8X cable, featuring stranded copper center, braided copper shield and a non-contaminating Type IIa PVC jacket. Okay for direct bury, our 8X DX Series cable assemblies are intended for moderate-power HF stations or mobile applications where short runs and flexibility are key factors. Slightly larger than RG-58 cable, DX Engineering RG-8X offers better handling characteristics and very good shielding. Plus, the gas-injected foam of DXE-8X cannot gather moisture and has lower loss than old RG-8X foam cables. The ferrite bead choke part of these cable assemblies should be connected to a grounded protector or the radio end of the cable, especially when used on End Fed Half-Wave or non-resonant antennas, random wires, and verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. DX Engineering RG-8X PL-259 Low-Loss RF Choke Coaxial Cable Assemblies are terminated with our custom-designed, silver-plated DX Engineering PL-259 (UHF male) connectors. The patented* Next Generation PL-259 connectors feature: * Full diameter, full length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double knurled threaded shells for secure finger tightening * All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity These ultra-high quality PL-259s have all silver-plated shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Order some extras in various lengths to have on hand for the next time you add to, change, or rearrange your equipment. DX Engineering RG-8X PL-259 Low-Loss 50-ohm Coaxial Cable Assemblies are perfect for every station! *U.S. Patent D745849

Not Yet Reviewed

$115.99

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259s, and select lengths with BNC connectors for POTA and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color delivered can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

4.96 out of 5 stars ( 23 )

$99.99

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies

DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Adapter Assemblies feature different silver plated connectors at each end – high quality BNC and PL-259s PTFE dielectric connectors – especially useful for POTA activations and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. DX Engineering RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are the most flexible and lowest loss high-quality orange coaxial cable assemblies on the market. DXE-8XV cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. The actual jacket color delivered can vary. DXE-8XV is the part number for this coaxial cable sold by the foot and is also available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 1 )

$99.99

DX Engineering RG-8X 50-ohm Coaxial Cable Adapter Assemblies

DX Engineering RG-8X 50-ohm Coaxial Cable Adapter Assemblies feature different silver plated connectors at each end – high quality BNC and PL-259s PTFE dielectric connectors – especially useful for POTA activations and portable operations. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering cable assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. DX Engineering RG-8X 50-ohm Coaxial Cable Assemblies are the most flexible, lowest loss and highest quality coaxial cable assemblies on the market. DXE-8X cable assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8X cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. DX Engineering DXE-8X is the industry standard specifications black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8X is the part number for this coaxial cable sold by the foot and it is also available in 1,000 ft. spools as DXE-8X-1000. DXE-8X Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 1 )

$89.99

DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies

DX Engineering RG-8X Hi-Viz Orange 50-ohm RF Choke Coaxial Cable Assemblies are the most flexible and lowest loss high-quality coaxial cable assemblies on the market. Assembled with fifteen Mix -31 ferrite beads under weather-sealed heat shrink, these DXE-8XV cables offer RF choking to reduce RFI and improve current balance on antennas. These flexible assemblies feature a stranded copper 16 AWG center conductor, gas injected foam dielectric, braided copper shield and non-contaminating, highly water-resistant Type II-A PVC UV stable direct-bury jacket. Our DXE-8XV High Visibility Orange cable assemblies are intended for HF portable applications where the visibility of short antenna cables and flexibility are desired. RG-8X High Visibility Orange 50-ohm Coaxial Cable Assemblies are terminated with high quality silver plated PTFE dielectric PL-259 (UHF male connectors. Their machine-crimped shields feature 360 degrees of complete mechanical and electrical contact for maximum reliability. All DX Engineering Cable Assemblies are Hi-Pot tested and heat-shrink weather-sealed for the ultimate in service longevity. The end of these cable assemblies with the ferrite bead choke should be connected to a grounded protector or to the radio, especially when used on End Fed Half-Wave or non-resonant antennas and random wires, and some verticals. They are also used at feed point of a dipole or Yagi antenna. Many installations can benefit from the use of an RF Choke Coaxial Cable Assembly, such as isolating the coaxial cable from a remotely tuned antenna system for improved performance. NOTE: DXE-8XV Orange will fade with continuous sunlight UV exposure. Color of delivered cable can vary. DX Engineering DXE-8XV Orange Jacket Coax has the same industry standard specifications as DXE-8X black jacket coax. DXE-8X is the coax cable most often used for jumpers in the shack and for medium length cables for portable operations, offering significantly better flexibility than larger cables, excellent shielding, and lower loss than smaller RG-58 and RG-174. DXE-8XV is the part number for this coaxial cable sold by the foot, and it is available in 1,000 ft. spools as DXE-8XV-1000. DXE-8XV Specs: Attenuation/100 ft. – Power Rating 0.65 dB @ 5 MHz – 3.0 kW 1.0 dB @ 10 MHz – 2.2 kW 1.5 dB @ 30 MHz – 1.2 kW For additional product information, please check the files in the "Documentation" section.

5.0 out of 5 stars ( 3 )

$133.99

DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies

What if two RF devices – the radio, switch, meter, lightning protector, choke, balun or the antenna – have opposite female connectors, one type-N and the other SO-239? This dilemma is solved with the uniquely helpful DX Engineering 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies, the perfect alternative to questionable straight adapters. Made for any job (HF, VHF and UHF) and especially for outdoors, one top-quality silver plated Type-N male connector and one patented* Next Generation PL-259 (UHF male) connector terminates our premium, low-loss 400MAX coaxial cable to create these very useful Adapter Cable Assemblies. DX Engineering 400MAX coax features a waterproof jacket made with a highly UV-resistant, Type III-A polyethylene which is ideal for all outdoor feedline applications, including direct-bury installations. With a large 10 AWG stranded copper center conductor, 400MAX NX Series low-loss assemblies are perfectly suited for short or long cable runs and low or high-power level operations. Our 400MAX coaxial cable also features modern, gas-injected foam polyethylene dielectric that cannot absorb moisture and has complete shielding with 100 percent coverage bonded aluminum tape covered by minimum 95-percent coverage tinned copper braid. Regarded in the industry as a top quality low-loss feedline, DX Engineering 400MAX Coaxial Cable is custom made to provide the highest performance and excellent longevity. Coaxial cables with foil-braid dual shielding or foam dielectric are optimized for stationary simplex antenna applications across HF, VHF and UHF. Note: DXE-400MAX is not recommended for use in repeater applications, VHF/UHF duplex, or for a beam antenna rotator loop. DX Engineering 400MAX PL-259 NX Series Coaxial Adapter Cable Assemblies are terminated at one end with the N-Type male connector and the other end with our custom-designed DX Engineering PL-259 (UHF male) connector. Both silver plated connectors feature machine-crimped shields with 360 degrees of complete mechanical and electrical contact for maximum reliability. PL-259 center pins are hand-soldered, and Type-N center pins are machine-crimped by trained assembly techs to assure a proper connection. Next Generation PL-259 connectors feature: * Full diameter, full-length soldered center pins that snugly fit even worn SO-239s * Spacious center pin inside diameter that accepts large conductors and allows generous solder flow * Deep, double-knurled threaded shells for secure finger tightening These high-quality PL-259s have all silver-plated brass shells and bodies with center pins securely mounted in PTFE dielectric for exceptional RF characteristics and power handling. Every assembly is continuity and Hi-Pot tested and then heat-shrink weather-sealed for the ultimate service longevity. You won't find this level of cable assembly quality anywhere else! 400MAX Type-N to PL-259 Low-Loss 50-ohm Coaxial Adapter Cable Assemblies are available in selected lengths and at any length in the Custom Cable Builder, only from DX Engineering! *U.S. Patent D745849

5.0 out of 5 stars ( 8 )

$238.40

Times Microwave Systems® Bulk Coaxial Cables

Times Microwave Systems Bulk Coaxial Cables are recognized as superior RF cable products. The standard Times Microwave LMR® is a UV-resistant polyethylene jacketed cable designed for 20-year service in outdoor use. Depending upon size, LMR® cable has a solid copper or copper clad solid aluminum center conductor. Their bending and handling characteristics are significantly better than air-dielectric and corrugated hard line cables. LMR-DB® cable has a waterproofing compound to prevent moisture intrusion after a minor abrasion. Times Microwave Systems EZ Series and TC Series connectors are suitable for use on standard LMR® and LMR-DB® cables. Times Microwave Systems LMR® UltraFlex (UF) cables have a stranded bare copper center and a rubber jacket (black thermoplastic elastomer) designed for repeated bending. Times Microwave TC Series crimp connectors are designed for use on LMR® UltraFlex cables. LMR®'s RF shielding is typically 50 dB greater than standard coax. The copper shield and multi-ply bonded foil outer conductor is rated conservatively at greater than 90 dB. That's better than 180 dB isolation between two adjacent cables. A wide variety of connectors are available for LMR cables, including all common interface types, reverse polarity, and a choice of solder or non-solder center pins. Most LMR connectors employ crimped outer attachment using standard hex-crimp methods. Times Microwave Systems is a premier supplier of coaxial cable products worldwide. Only Times offers a range of products specifically developed to perform as needed in the most diverse range of environments. Times Microwave Systems has over 60 years of experience in building the highest-quality cables. Order LMR® coaxial cables from DX Engineering and put Times Microwave Systems Bulk Coaxial Cables to work for you! LMR® is a registered trademark of Times Microwave Systems.

4.88 out of 5 stars ( 106 )

$2.83

Alpha Delta F Connector Coaxial Cable Surge Protectors

Alpha Delta F Connector Coaxial Surge Protectors are rated for 200 or 2,000 watts at frequencies up to 3 GHz. They are not DC-blocked, so they will pass control and power voltages in applications requiring the coaxial cable to carry both RF and DC voltage. They can be easily mounted for the most effective grounding with their 1/4-20 in. stud in a single hole, or as a bulkhead through the grounding panel. In a study under the auspices of the U.S. Dept. of Energy, utilizing the satellite FORTE launched in 1997 carrying VHF lightning discharge sensors, it was determined that there can be damaging lightning energy emissions throughout the 30 through 300 MHz VHF spectrum. Before FORTE, it was thought that most lightning energy emissions were primarily in the VLF range. Therefore, the damage threat can be anywhere from VLF through VHF. Through the careful design of the Alpha Delta Arc-Plug® gas tube module and precision, constant impedance through-line allowing proper firing characteristics, these devices are designed to provide effective protection throughout this entire spectrum. Other surge protector designs may only utilize simple VLF filters with no gas tube backup. Additional features include: * Excellent broadband performance from DC through 3 GHz, compared to the narrow-band DC-blocked or stub designs. Typical dB loss: 0.1@ 1 GHz; 0.2@ 2 GHz; and 0.5@ 3 GHz. * Innovative impedance-compensated, through-line cavity design allows control voltages to pass through the devices, instead of the "wire-around" requirement of DC-blocked designs. This design allows "in-circuit" cable sweeps. * Innovative, fast-acting gas tube replaceable Arc-Plug® module can be removed and replaced in the field in about one minute with no tools required, and without having to remove the protector from the circuit. The "O" ring sealed knurled knob does the trick! * The Arc-Plug® module and connectors are "O" ring sealed for complete weatherproofing. * Effective performance. Due to the carefully designed reactance-compensated, through-line cavity and Arc-Plug® module placement, customer and government test approvals show that this design is as good as, or better than, DC-blocked designs. Lightning surges do lots of damage annually. Protect your equipment from surges with Alpha Delta F Connector Coaxial Surge Protectors from DX Engineering!

5.0 out of 5 stars ( 3 )

$75.99

—

$79.99

NexTek PTC Series DC Pass Coaxial RF Lightning and Surge Protectors

NexTek PTC Series DC Pass Coaxial RF Lightning and Surge Protectors are tough, long-lasting gas discharge tube arrestors that provide wideband performance designed to protect your equipment from electromagnetic pulse (EMP) or power surges that are commonly caused by lightning or other strong electrical charges. These arrestors will pass DC current and features excellent performance with no degradation of signal with proper installation in Amateur Radio and remote industrial monitoring and SCADA (Supervisory Control and Data Acquisition) applications. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. NexTek PTC Series Features and Specifications * Frequency Range - Up to 3.0 GHz (model dependent) * Low SWR and Insertion Loss * DC Pass Capability * Bulkhead Mount * Multi-Strike Capability * Max Surge Current of 20 kA * Multi-Strike Capability - 10 kA 10 Times * Max RF Power 25 W * Impedance – 75 Ohms * Gas Discharge Tube – 90 V * Rugged and Waterproof * Bi-Directional Protection * Compatible with RG-6 Cable

Not Yet Reviewed

$59.00

CITEL Coaxial Cable Surge Protectors

CITEL Coaxial Cable Surge Protectors are engineered to provide robust protection against transient over voltages. These devices utilize advanced gas discharge tube (GDT) technology to effectively dissipate high-energy surges, ensuring the safety and longevity of connected equipment. CITEL Coaxial Cable Surge Protectors offer low insertion loss and high surge handling capacity, making them ideal for Amateur Radio station installations, as well as both commercial and industrial environments. With features such as waterproof housings and field-replaceable gas discharge tubes, CITEL Coaxial Cable Surge Protectors are built for durability and ease of maintenance, providing reliable performance in even the harshest conditions.

Not Yet Reviewed

$64.99

DX Engineering EX6XL Type-F Universal Compression Connectors

DX Engineering EX6XL Type-F Universal Compression Connectors work on all RG6U coaxial cables, solving the problems of trying to identify cable type and figuring out which compression connector to use. This connector's unique design fits any RG6 and RG6U coaxial cables, standard or self-healing (flooded). They install onto RG6U 60% braid, dual shield, such as RG-6U and F-6, including legacy DXE-F6 and DXE-6UF, as well as all Quad Shield RG-6U including DXE-RG6UFQ and DXE-RG6UQ. These F connectors have a long, rugged metal body, heavy duty black plastic and are direct replacements for all previous blue and purple F connectors. They are easily installed with common F-connector installation compression tools including DXE-SNS-CT1. Features of the DX Engineering EX6XL Type-F Universal Compression Connectors: - O-ring is a redundant seal and is always compression sealing, regardless of torque - Large tapered compression area creates a redundant moisture-tight interface - Three circumferential gaskets seal the body to the post - Gas-tight seal connection between the nut and the post Specifications: Bandwidth: 0 to 3 GHz Impedance: 75 ohm (nominal) Return Loss: Minimum -30 dB to 3 GHz Insertion Loss: Less than .10 dB to 3 GHz Operating Voltage: 90 V (at 60 Hz continuous AC) Operating Temperature:-40 F to + 140 F (-40 C to 60 C) Cable Retention: 45 lbs. (20.41 kg) minimum Meets or exceeds all SCTE Specifications

3.33 out of 5 stars ( 6 )

$13.99

—

$27.99

United Microsystems BT-75/BOG Beverage-On-Ground Antenna Transformers

The United Microsystems BT-75/BOG Beverage-on-Ground (BOG) Antenna Transformers are specifically designed for Beverage-on-Ground receive antennas and is based on the proven BT-75 transformer used with elevated Beverage antennas. Because BOG antennas are installed directly on or just above the ground, they require no supports and can be significantly shorter than traditional Beverage antennas, making them a practical option where space is limited. BOG antennas typically exhibit lower impedance than elevated Beverage antennas. The BT-75/BOG is optimized to provide proper impedance matching between the antenna and 75-ohm RG-6 coaxial cable, improving performance compared to standard Beverage transformers. For correct operation, the far end of the antenna must be terminated with a 250 to 300-ohm resistive load. The United Microsystems RXT-270 termination resistor is recommended. Properly installed Beverage antennas are low-noise, receive-only antennas that provide excellent rejection of signals and noise from the undesired direction. Due to the lower velocity factor of radio waves near the ground, a BOG antenna can often deliver a radiation pattern similar to an elevated Beverage antenna of roughly twice the length, though with reduced signal strength. A BOG antenna as short as 150 to 200 feet can provide effective receive performance, although a preamplifier may be beneficial in some installations. The BT-75/BOG is designed for use with 75-ohm RG-6 coaxial cable. Originally developed for television applications, RG-6 offers low loss at VHF and UHF frequencies, resulting in extremely low loss on the 160, 80, and 40-meter bands. Its availability and low cost make it a popular choice for low-band receive antenna feed lines. The transformer is housed in a NEMA-rated enclosure with stainless steel hardware for long-term outdoor durability. A built-in gas discharge tube across the antenna terminals helps protect the transformer from nearby lightning-induced surges, although it will not provide protection against direct or very close lightning strikes.

Not Yet Reviewed

$37.95

DX Engineering AVA-3 Active Matching Units

DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.

5.0 out of 5 stars ( 6 )

$139.99