Availability
55 Results Found For "anchor"
DMV Rope Guying Earth Anchors
DMV Rope Guying Earth Anchors are designed for use on ropes to build a custom guying system for your vertical antenna. They are manufactured from high-quality steel and have a protective finish applied for long-lasting durability. DMV Rope Guying Earth Anchors feature a specially designed twisted base to allow for easy installation in the ground. Specifications: - Shaft Diameter: 0.5 in. - Loop Height: 2.24 in. (loop tip to outside top of the loop) - Anchor Length: 15.00 in. - Anchor Width: 3.0 in.
Not Yet Reviewed
$11.99
—
$47.96
Chelegance JROD-30 Rope Guying Anchors
Chelegance JROD-30 Rope Guying Anchors are 11.81 Inches long and designed to be screwed down into the ground to provide a solid point to attach rope for guying a portable tripod or mast. Comes with two tools to assist in screwing the anchors in: a manual T-shaped handle and a bit to attach to a battery-operated drill. Featuring a spiral design 6 inches long, and a center rod that is 0.5 inches in diameter, these anchors are easy to drive into most soil and will stay put. Sold as a set of four.
Not Yet Reviewed
$33.99
Mastrant Rope Guying Earth Anchors
Mastrant Rope Guying Earth Anchors are perfect for guying small portable masts and vertical antennas and make an ideal accessory to secure the Mastrant Guying Kits . Weighing only 125g (0.28 lb.), they are lightweight and ideal for portable operation, or expedition activities. Designed for use with ropes, they help you build a custom guying system for your portable mast or vertical antenna. Made from high-quality lightweight aluminum, these earth anchors feature a 0.28in. (7mm) anchor hole to securely attach rope, carabiner, or chain link coupler .
Not Yet Reviewed
$8.99
Amerite Anchor Bases
Some hams like to look for options when doing concrete tower bases. American Tower Company Amerite Anchor Bases give you another option: Instead of burying part of a tower section in concrete, you may find that using a tower-anchor base cage better suits your needs. These anchors are available for Amerite 25 and 45 Series towers. Included with the AME-25-ABC: Three 1/2 by 3 by 6 in. bar with three 1-1/4 in. diameter tower stubs Three 3/4 by 3/4 by 1/8 in. angle brackets Six 1/2 by 18 in. "J" bolts with nuts Included with the AME-45-ABC Three 1/2 by 3 by 6 in. bar with three 1-1/4 in. diameter tower stubs Three 3/4 by 3/4 by 1/8 in. angle brackets Six 3/4 by 18 in. "J" bolts with nuts Once assembled, these anchor bases may be embedded in concrete to provide a fixed base for your tower. Order your American Tower Company Amerite Anchor Bases from DX Engineering!
Not Yet Reviewed
$268.99
—
$315.99
Universal Towers Tower Base Anchors
Universal Towers Tower Base Anchors are designed for use with Universal Towers towers. Ensure correct fitment by choosing your corresponding tower section. Universal Towers tower bases are constructed from high-quality materials and engineered for high strength and durability. Give your tower a proper foundation with Universal Towers Tower Base Anchors from DX Engineering.
Not Yet Reviewed
$185.25
—
$429.40
ROHN Guy Anchor Rods
ROHN Guy Anchor Rods allow for the attachment of up to five levels of guy wires. Some models are provided with a top plate for guy wire attachment and are designed to be installed in a concrete base. All are galvanized for extended service.
( 3 )
$279.99
—
$539.99
ROHN RAL Series Tower Base Anchors
ROHN RAL Series Tower Base Anchors are designed specifically for RSL towers. Choose the proper product number based upon the bottom tower section. For example, RAL10 is the correct part when an RSL10 is the bottom tower section. RAL Series bases include a foundation template to insure the base is set in the proper place when embedding in concrete. These bases employ a double-nut system that is used for limited tower leveling after the foundation is poured. When you install an RSL tower, remember to order your ROHN RAL Series Tower Base Anchors from DX Engineering as well.
Not Yet Reviewed
$1,349.99
—
$1,799.99
ROHN Tower Base Bolts
ROHN Tower Base Bolts are galvanized steel bolts that are set into the concrete base pier when it is poured. These bolts anchor ROHN Tower Concrete Base Plates and Hinged Base Plates to the concrete pier.
( 4 )
$31.99
—
$499.99
TBX Tower Base Stubs
TBX Tower Base Stubs facilitate mounting the bottom of the tower to the concrete tower base. These are literally stubbed tower-leg sections that are 4 ft. in length. Each base stub number corresponds to the tower section that the stubs fit. That means that a TBX-BS-3 will fit the TBX-3 tower section. The TBX-BS-7/8 will fit both the TBX-7 and TBX-8 tower sections. Use these base stubs to anchor your TBX Tower when NOT using a tilt-base. For tilt-base applications, use the recommended anchor bolts. TBX Towers are deluxe steel towers that won't break the bank! When you want to anchor one of your own TBX towers, contact DX Engineering for some TBX Tower Base Stubs!
Not Yet Reviewed
$210.00
—
$280.00
DX Engineering Radial Wire Metal Anchor Pins
DX Engineering radial wire metal anchor pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your radials during lawn maintenance. They are manufactured from 11-gauge steel and are 6 in. long to help keep the cables buried properly.
( 39 )
$22.99
—
$59.99
DX Engineering Radial Wire Biodegradable Anchor Pins
DX Engineering Radial Wire Biodegradable Anchor Pins are designed to keep your cables down to the ground in an Earth-friendly way. They are manufactured from recycled, bio-degradable, PLA (polylactide) resin, the color of which will vary. These biodegradable anchors are easily installed and will hold radial wires in place until lawn roots overtake them, and then disappear. They're ecologically friendly! Depending on the weather conditions, they will degrade in about a year. They don't slowly rust away like metal staples. DX Engineering Radial Wire Biodegradable Anchor Pins are intended for turf or softer ground where they may be pushed in (they feature a wide, flat head for your thumb) or lightly tapped with a tool head--NOT driven in with a hammer. Since they are a plastic-like material, they will be subject to breakage when used in rocky or hard soil or subjected to vigorous impact. Install your ground radials the easy and ecological way- with DX Engineering Radial Wire Biodegradable Anchor Pins!
( 41 )
$19.99
Chelegance Guy Line Anchors
Chelegance Guy Line Anchor Rods are made from steel with a shaft diameter of 9mm, just under 3/8in. and they are 7.9 inches in length, with a built-in hook that makes tying off your guy ropes a breeze. Sold in packs of 4.
Not Yet Reviewed
$20.99
ROHN 25G/45G-Series Guy Anchor Grounding Kits
ROHN 25G/45G-Series Guy Anchor Grounding Kits are so important that they are included in each ROHN 25G and 45G complete tower package. However, when purchased from ROHN separately, this part number includes only the 30 ft. of 7/16 in. ground wire, three 10 ft. copper-clad 5/8 in. ground rods and three 3/4 in. ground rod clamps. The required R-CPC.5/.75 anchor rod clamps (three) that connect to the actual Guy Anchor Rod (and are needed to complete the grounding installation) are sold separately. Also, as these kits contain items 10 ft. in length, they can only ship truck freight. Tower grounding is the single most important effort in protecting your shack from lightning. Order these ROHN 25G/45G-Series Guy Anchor Grounding Kits from DX Engineering and improve your tower grounds.
Not Yet Reviewed
$399.99
ROHN Guy Anchor Ground Clamps
ROHN Guy Anchor Ground Clamps are used in conjunction with their Guy Anchor Grounding Kits (ROH-AGK1GGX) to provide an efficient guy-anchor ground. These grounding clamps fit round members (rod) from 0.5 to 0.75 in. nominal diameter. They will clamp AWG 6 solid or up to 7/16 HS or EHS wire rope to the solid round rod. These clamps are of tinned bronze and stainless hardware. Tinned bronze is corrosion resistant and will last a long, long time. Their high-compression U-bolt really applies pressure to the conductor and anchor rod. This high pressure creates a low-resistance connection for effective grounding. Order ROHN Guy Anchor Ground Clamps from DX Engineering!
Not Yet Reviewed
$45.99
DX Engineering Vertical Antenna Guying Kits
Some vertical antenna manufacturers indicate that their antennas do not need guying. During times of high winds or ice loading, however, some of these vertical antennas may sustain damage or fail altogether. With the small amount of effort needed to install one of these DX Engineering Vertical Antenna Guying Kits, the risk hardly seems worth taking. They feature a 4-point guying scheme that provides the best mechanical advantage to prevent wind stress, regardless of direction. The guying is intended for stability only and should never be depended on for primary support. DX Engineering Vertical Antenna Guying Kits are especially recommended for use with DX Engineering tilt bases, because just one of the guy ropes has to be loosened when you tilt the vertical down. The remaining guys help to stabilize the vertical in three directions when being raised. These kits have been designed to be used with ground-mounted quarter-wavelength vertical antennas, such as DX Engineering monoband and multiband verticals and the Hustler 4, 5, and 6-BTV models. Using the DX Engineering vertical antenna guying kits, you can install four guy ropes approximately halfway up the vertical antenna system to ground level and angled at approximately 45 degrees. Guying should be tightened just enough to permit the antenna to swing a few inches. The ends of the ropes are tied to the earth anchors that are screwed into the ground at about the same angle as the ropes. Tie the other ends of the ropes to the vertical antenna just above one of the antenna element clamps or traps (a guying ring is not required). Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. The DX Engineering Vertical Antenna Guying Kits are available in different lengths to fit your varying vertical antenna needs.
( 9 )
$61.55
—
$126.95
ROHN TBSAFETY Turnbuckle Safety Kits
ROHN TBSAFETY Turnbuckle Safety Kits include 45 ft. (15 ft. per guy anchor assembly) of 1/4 in. high strength guy wire to secure your turnbuckles and 6 matching 1/4 in. forged and galvanized U-bolt clips for final fastening of the safety wire on each of three guy anchors. In other words, use 15 ft. of guy wire and 2 clips on each guy-anchor assembly for protection against turnbuckle loosening or catastrophic failure. Turnbuckles, like all metal exposed to the elements, degrade over time. These safety kits thread through the turnbuckles and guy-line terminations (thimbles and eyes) in figure-8 fashion to make everything secure. Don't allow your tower to collapse due to turnbuckle failure. Order your ROHN TBSAFETY Turnbuckle Safety Kits from DX Engineering and make your tower installation safer!
Not Yet Reviewed
$71.99
ROHN TRTBAG Lag Bolt Kits
ROHN TRT-Series roof tripods are very popular. But the trip to the hardware store to get lag bolts for mounting them is not. When you order a TRT-36 or TRT-60 tripod you can order the lag bolts, too. ROHN TRTBAG Lag Bolt Kits contain the six lag bolts that you'll need to install your tripod. They even include 6 rubber-backed steel washers to seal under the bolt heads. These lag bolt kits include high-quality steel bolts that are galvanized for corrosion resistance and long life. Their shouldered hex heads are easily driven with box wrenches or sockets. These bolts are 2.00 in. long and 3/16 in. thread diameter with 3/8 in. hex heads. Whether using ROHN TRT tripod roof towers or some other permanent-mount brand we offer, these lag bolt kits will provide the strong, reliable attachment you need. Order your ROHN TRTBAG Lag Bolt Kits from DX Engineering today!
Not Yet Reviewed
$17.99
PolyPhaser Coaxial Lightning Protectors
PolyPhaser Coaxial Lightning Protectors are designed for general, single-transmitter use in the 1.5 to 700 MHz frequency range. PolyPhaser protectors are available in two mounting styles: "Bulkhead Mount" protectors have a longer connector and hardware to mount it through the grounding panel. "Flange Mount" protectors anchor to a grounding panel with both connectors parallel to a flat surface. PolyPhaser Coaxial Lightning Protectors use a DC blocked specially configured gas tube design that has no DC continuity between the two center pins. PolyPhaser's multi-strike products are designed to pass RF frequencies and block all DC. These protectors appear as a DC open between surge and protected ports and offer industry-standard protection. PolyPhaser protectors are suitable for all types of antennas, even "floating" antennas that are not DC grounded. With PolyPhaser DC Blocked protectors, any slow voltage build up from wind driven rain, snow or dust, will not get to the equipment. As the protector reaches threshold for turn-on in a dc blocked circuit, it will go into a momentary soft turn-on as the gas barely ionizes and bleeds the static charge to ground. This does not create noise since it will not get to the arc mode and lasts only a short time. PolyPhaser protection devices have been chosen and specified by communications systems engineers and technicians for 24/7 service in broadcasting, commercial, military and government installations. Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Trusted by Amateur Radio operators for over 40 years, PolyPhaser Coaxial Lightning Protectors are ready for your antenna system installations. They are available here, at DX Engineering.
( 64 )
$93.99
—
$161.99
ROHN Self-Supporting Concrete Base Plates
ROHN self-supporting tower base plates ensure the proper installation of your ROHN 25G or45G series tower when anchored to a concrete base with 5/8 x 12.0 in. bolts. ROHN concrete base plates are made from durable, 1/2 in. thick galvanized steel.
( 1 )
$349.99
ROHN BPC25G Concrete Base Plates
These ROHN BPC25G Concrete Base Plates provide an easy and secure way to mount your guyed or bracketed ROHN 25G tower to a concrete pier, without the need for embedding a tower section in concrete. With these base plates, only a single 3/4 x 12 in. Pier Pin embedded in the standard concrete base is required to anchor the base of a ROHN 25G Series guyed tower. This is possible since lateral forces are minimized at the base of the tower. A slight pivoting of the pier pin anchored tower base is natural and allowable, as virtually all of the guyed tower forces are exerted vertically onto the concrete pier. BPC25G Concrete Base Plates are completely hot-dip galvanized after fabrication and are designed to work only with Rohn 25G Series straight tower sections. Setting the standard in towers for decades, Rohn has supported more ham antennas than any other brand. Start your tower build with one of these BPC25G Concrete Base Plates from DX Engineering!
( 6 )
$129.99
ROHN Tripod Roof Towers
ROHN tripod roof towers or TRTs feature a universal mast clamp that is capable of mounting masts with up to 1 3/4 in. diameters and swivel feet that adjust to the pitch of almost any roof. Installation is simple and fast with lag screws or bolts (not included) through the feet that securely anchor the towers for long, trouble-free service. ROHN tripod roof towers feature a lower mast support bracket and hot-dip galvanized construction for corrosion protection.
( 25 )
$129.99
—
$159.99
WiMo Tripod Foot Plates
WiMo Tripod Foot Plates are sold in sets of three and are used on the legs of WiMo Mast Tripods to stabilize them on sandy soil or to level the tripod on an incline. Tripod Foot Plates are 240 x 120mm (9.45 x 4.72 in.) aluminum plates. Tubular leg attachments allow for the tripod legs to slide in and then clamped into place, allowing for a height adjustment range of up to 100mm (3.9 in.) A hole in the Tripod Foot Plates allows anchoring with a ground stake (not supplied).
( 1 )
$129.99
Chameleon Antenna CHA Sling Bags
Chameleon Antenna Sling Bags are the perfect companion for your Chameleon MPAS 2.0 series antenna and all of its accessories. The bag is made with water and abrasion resistant 900D Oxford cloth and will survive most things that you will throw at it in the field or on the summit. Featuring a pair of large pockets on the front with adjustable buckle closures for small items such as matching networks and coax. Internally, this 30 x 6in. bag has straps for holding items in place. A padded shoulder strap ensures comfort while carrying the bag in a sling configuration and padded handles on the side ensure comfort and options for transport. Molle straps provide for additional points to use to anchor items needed for successful portable operation. Specifications: • 1 x Chameleon Antenna Velcro Patch • Double Layer Water Resistant • Single Shoulder Strap w/ Buckle Adjustment • Interior Straps • Side Handle • Heavy Duty YKK Zippers For Side Opening • 2 x Large Front Pouch w/ Buckle Adjustment • Molle Straps • Weight: 4.5lbs. • Material: 900D Oxford cloth • Color : Tan • Dimensions: 30.0 x 6.0in.
( 2 )
$80.00
Vibroplex Straight Keys
Vibroplex straight keys are a first for Vibroplex in its 100+ year history. Their design is distinctly Vibroplex. Their heavy, solid-steel base anchors the straight keys to the operating position, while their lever arm pivots in the famous chromed mainframe. An adjustable stainless steel spring allows for complete control of the tension. And, of course, the straight keys have the famous brass Vibroplex logo plate with a unique serial number pinned to the top of the base with stainless steel pins. They are available in standard, deluxe, and 24K gold finishes. Vibroplex straight keys have unique mechanical action, unlike any other straight keys that have ever been manufactured. Their smooth action and heavy steel base allow the operator to send perfect code.
( 23 )
$189.95
—
$322.95