Filters
ACOM Antennas
ACOM eBox Ethernet Remote Control Devices
ACOM eBox Ethernet Remote Control Devices directly integrate ACOM power amplifiers to Ethernet networks for Internet Remote operations. ACOM eBox is specifically designed for use only on ACOM power amplifiers. DX Engineering sells the two versions available, sold with different interface cables: * AOM-EBOX-SS for ACOM 600S, ACOM 700S and ACOM 1200S * AOM-EBOX-2000 for ACOM 2000A with RCU The eBox receives the amplifier's specific commands via Ethernet interface and forwards them to the ACOM amplifier. EASY to OPERATE There is no software to install! The administration of the eBox is done via Web-based programming interface specially developed for ACOM amplifiers. You can use any personal computer running any operating system. You just need to run web browser as Chrome, Opera, Firefox, MS Edge, Safari, etc. ALWAYS UP-TO-DATE Your eBox is always up-to-date due to its integrated function for firmware update. The newest firmware versions are available (usually as *.bin files) at www.acom-bg.com. With just a few clicks you can upload a new firmware to the eBox. ACOM eBox SPECIFICATIONS: * Remote control capabilities via Ethernet * Suitable for use with ACOM 600S, 700S, 1200S and 2000A Power Amplifiers * Web browser-based user-friendly interface NOTE: Included universal 100-240 VAC wall mount power supply with European plug is adapted to North American plug with DMV-EURO-US-PLUG, included in eBox combination models ending in -P.
( 7 )
$749.99
—
$757.98
ACOM ASW-120 Remote Antenna Switch and Selector Sets
ACOM ASW-120 Remote Antenna Switch and Selector Sets contain two essential components: the 2000SW Remote Antenna Switch and the 2000S Automatic Antenna Selector, pre-set internally for 120 VAC with a USA plug installed on the power cord. This combination system provides complete antenna selection automation when interfaced with the Acom 2000A Automatic HF Linear Amplifier, or it may be used as a manually or PC controlled antenna switching system. The included 2000SW Remote Antenna Switch is a rugged, high-quality weatherproof outdoor relay unit with 10 antenna ports and 1 common port, all PTFE UHF female (SO-239) connectors useable up to 60 MHz. At low SWR this switch handles up to 5,000 W at 30 MHz and 3,600 watts at 50 MHz. Hot-switching protection is provided and unused antenna inputs are automatically grounded for surge suppression. Relay water intrusion protection is at the IP53 level. These remote switches will tolerate a very wide temperature range and operate on a control voltage range of 24 to 31 VDC, as supplied by the 2000S Automatic Antenna Selector. The included 2000S Automatic Antenna Selector, as shipped in the ASW-120 package by DX Engineering, has a power cord terminated with a NEMA 5-15P plug for 120 AC. No additional power supply is required. The system uses a 4 bit BCD selector signal and incorporates a feedback signal to the controller. Connection of the 2000S Selector to the 2000SW Switch requires a minimum of a 7-conductor shielded control cable of AWG-24 (CAT5e) which is sufficient to about 165 feet. A longer control cable will require a larger wire gauge. Connectors included require soldering. Also included are a 3-meter length of 7-conductor control cable and 1 interface cable for connecting the controller to the ACOM 2000 amplifier. Here are the Specifications of the ACOM ASW-120 Remote Antenna Switch and Selector Sets: * Operating Frequency: 0 to 60 MHz. * 10x UHF female (SO-239) PTFE connectors * Power Handling vs. SWR: 0 to 30 MHz: 5000W at 1:1; up to 2500W at 2:1; up to 1600W at 3:1 * Power Handling vs. SWR: up to 60 MHz: 3600W at 1:1; up to 1800W at 2:1; up to 1200W at 3:1 * Mismatch VSWR: for 0 to 1.8 MHz better than 1.02:1; 1.8 to 30 MHz better than 1.08:1; 30 to 60 MHz better than 1.20:1 * Crosstalk isolation: for 0 to 1.8 MHz-better than -100dB; 1.8 to 30 MHz -better than -70dB; 30 to 60 MHz better than -66dB * Relay Changeover Time: Less than 150 milliseconds including any relay chatter * Operating temperature range: minus 30 to plus 60 degrees C * Water Intrusion: IP53 * Power Supply: 120 VAC, NEMA 5-15P three-prong power plug (USA) * Total shipping weight 6kg (products 4kg) NOTE: This Acom ASW-120 Remote Antenna Switch and Selector Set is available from DX Engineering ONLY as a 120 VAC system. The internal selection is pre-switched to 120 VAC and the power cord is pre-wired with a NEMA 5-15P three-prong grounded plug, as a convenience for our North American customers. This negates mention in the 2000S Manual of "Normally the unit is supplied with Voltage Selector set for…240 V." This is not the case of the ASW-120 purchased from DX Engineering, therefore is not necessary to "…contact the dealer for details…" The 120 VAC selection has been made in advance for every ASW-120 set. The "Documentation" tab provides links to each unit's manual which include additional product information that is useful. For a remote antenna switch and controller of excellent design, order ACOM ASW-120 Remote Antenna Switch and Selector Sets from DX Engineering!
( 1 )
$959.99