Availability
Yaesu Antennas
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems
Yaesu G-800DXA Medium Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 20 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-800DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-800DXA Medium Heavy-Duty Rotator System from DX Engineering.
( 23 )
$659.99
Yaesu G-450ADC Medium-Duty Rotator Systems
Yaesu G-450ADC Medium-Duty Rotator Systems are the entry-level rotator and controller that are perfect for small HF beams, a tri-bander or VHF and UHF antennas up to about 10 sq. ft. of tower-mounted wind load. A lesser wind load of about 5 sq. ft. can be handled when mounting the G-450ADC on top of a mast with the optional lower mast bracket, GC-038. Rotate Amateur and professional antennas with the Yaesu's handsome 120 Vac desktop remote control console, featuring a compass-style indicator at the station operating position. The G-450ADC rotator system provides 450 degrees of azimuth rotation in just over one minute. The rotator handles masts of 1.25 to 2.48 in. outside diameter and, when tower mounted, a total vertical mast load up to 200 lbs. In the Yaesu G-450ADC, the clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-450ADC Rotator motors and controllers operate with a 20 V DC control voltage, four-wire system, using the provided connectors to be installed at each end of the user supplied control cable, same as the previous models. For clarity, the new DC rotator motors are marked "G-450DC" at the connector. The rear panel of the controller is titled "G-450ADC" on the serial number label. WARNING: The legacy Yaesu G-450A Rotator motors and controllers used a 26 VAC control voltage, five-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-450ADC components, which only use pins 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use four-conductor, 20 gauge control cable (4 x 20 AWG). If the rotator cable needs to be longer than 125 ft., then use four-conductor 18 gauge cable (4 x 18 AWG). The input voltage for the G-450ADC controller is labeled "117 VAC" to indicate house current of 110 to 120 Vac. When you need a medium-duty rotator system, which is durable and attractive, order a new Yaesu G-450ADC Medium-Duty Rotator System from DX Engineering.
( 45 )
$429.99
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-2800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 30 sq. ft. of antenna wind load and over 650 lbs. of vertical mast load. About 130 ft. of control cable is included with the G-2800DXA only. Control console power is 110/120 volts AC. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 50 to 120 seconds on the G-2800DXA, and preset a desired heading for the rotator, to which it then turns automatically. When a fast rotation speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-2800DXA Extra Heavy-Duty Rotator System from DX Engineering.
( 1 )
$1,769.99
Yaesu G-1000DXA Heavy-Duty Rotator Systems
Yaesu G-1000DXA Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-1000DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-1000DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 23 sq. ft. of antenna wind load and over 400 lbs. of vertical mast load. Installation is required for included plug connectors on to the installer supplied 6-conductor control cable; 20 AWG for lengths less than 125 ft. and 18 AWG over 125 ft. Console power is 117 volts AC for units sold in the USA. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 40 to 100 seconds on the G-1000DXA, and preset a desired heading for the rotator, to which it then turns automatically. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-1000DXA Heavy-Duty Rotator System from DX Engineering.
( 14 )
$799.99
Yaesu G-5500DC Azimuth-Elevation Rotator Systems
Yaesu G-5500DC Azimuth-Elevation Rotator Systems are specially designed to accommodate horizontal cross-booms to mount pairs of VHF and UHF directional antennas for space communications. Providing simultaneous control of 450 degrees of azimuth rotation and 180 degrees of elevation rotation, they are perfect for EME (moon bounce) and satellite communications installations. The G-5500DC dual controller lets you adjust and keep track of both aspects of the antenna system's positioning. The 120 VAC controller includes an interface jack for computer control, supported by the optional GS-232A Computer Controller, as well as many aftermarket control programs and interfaces. These azimuth and elevation rotators are actually two separate motor units, now DC controlled. They may be mounted together on a mast with the included mast bracket, or independently with the azimuth rotator inside a tower and the elevation rotator mounted on the mast above the top of the tower. They handle a total of about 10 sq. ft. of antenna wind load and rotate each way in about one minute. The Yaesu G-5500 AZ-EL clamshell rotator design utilizes 98 heavy 7/16-inch dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear, and practically eliminates the possibility of destructive water entry: there is no shaft hole in the top of the housing. Yaesu's factory-lubricated rotator units are housed in Melamine resin-coated die-cast aluminum intended to provide maintenance-free operation under all climatic conditions. IMPORTANT NOTE: Beginning in 2019 the new Yaesu G-5550DC azimuth and elevation motors operate with two independent 22 V DC control lines, each a five-wire system, using the same connectors at the end of the control cable as the previous models. Both of the new DC motors, azimuth, and elevation, are marked "G-5550DC" at the connector. Be sure to mark your connectors AZ or EL. The rear panel of the controller is titled "G-5500DC" on the serial number label. WARNING: The legacy Yaesu G-5500 Rotator motors and controller used a 26 VAC control voltage, six-wire system. Therefore, old AC controllers are NOT compatible with new DC rotator motors, and new DC controllers are not compatible with old AC rotator motors. All control cable assemblies for all modern Yaesu rotator systems use the same connectors with "1 to 1 pin-out" connector wiring. Therefore, older cable assemblies are compatible with the new Yaesu G-5500DC components, which only use pins 1, 2, 3, 4 and 5 in each connector. For control cable runs less than 125 ft. use five-conductor, 20 gauge control cable (5 x 20 AWG). If the rotator cable needs to be longer than 125 ft. then use five-conductor 18 gauge cable (5 x 18 AWG). The input voltage for the G-5500DC controller is labeled "117 VAC" to indicate house current range of 110 to 120 Vac. When you are launching your EME or satellite communications adventure, an azimuth/elevation combination rotator is a vital tool for your antenna system. As durable as they are attractive, Yaesu G-5500DC Azimuth-Elevation Rotator Systems are available from DX Engineering.
( 17 )
$969.99
Instant Rebate
Yaesu ATAS-120A Auto Active Tuning Antennas
Yaesu's patented ATAS™ Active Tuning Antenna System has been enhanced with the latest model: ATAS-120A. This is a unique mobile antenna that provides HF, VHF and UHF coverage with automatic motorized tuning. Designed for use exclusively with Yaesu transceivers that support ATAS, microprocessor controlled voltages are sent on the coaxial cable to adjust the antenna radiator length for best SWR. Yaesu ATAS-120A active tuning antennas cover the 7, 14, 21, 28, 50, 144 and 430 MHz Amateur bands and are compatible with the Yaesu FTX-1, FT891, FTDX-10, FT-710, FT-991A, FT-991, FT-857D, FT-897D, FT-100, FT-100D and the FT-450D. They are typically attached to a vehicle hatch or trunk lip UHF mount (not supplied), also available from DX Engineering. The ATAS-120A antennas were designed for mobile use, however they can be adapted for base, or portable operation with the appropriate mount and a substantial counterpoise radial wire system. Specifications of the Yaesu ATAS-120A Auto Active Tuning Antennas: * Operational Bands: 40, 20, 15, 10, 6 and 2 meters and 70 cm * Height, appx.: 4.59 to 5.25 ft. * Weight, appx.: 1.98 lbs. * Input Impedance: 50 ohms * Maximum Power: 120 Watts, SSB, CW, 50 percent duty cycle * Matched SWR: Less than 2.0:1 with proper grounding or counterpoise As with any HF, VHF and UHF mobile antenna, performance depends upon the grounding of the mount and bonding to the metal vehicle surfaces to create an optimal ground plane. Portable VHF and UHF operation is made possible with the addition of the optional Yaesu ATBK-100 Antenna Base Kit. This kit is not required, nor should it be used, for mobile operation. Operational convenience and performance is available for your Yaesu HF, VHF and UHF Mobile Transceiver. Order Yaesu ATAS-120A Active Tuning Antennas from DX Engineering.
( 49 )
$349.99
Yaesu SCU-LAN10 Network Remote Control System
Yaesu SCU-LAN10 Network Remote Control System brings the advanced functionality of Ethernet LAN port direct remote control to the unparalleled FTDX-101D and FTDX-101MP Transceivers and the impressive, compact and affordable FTDX10 Transceiver. All of the excitement of these phenomenal radios is available to any PC, on your local network or via the Internet from anywhere in the world, with the SCU-LAN10 interface units connected to the transceiver and a local network or the Internet. SCU-LAN10 Network Remote Control Software is available for download from www.yaesu.com Also available from the same link is the required Firmware Update versions listed here for the FTdx-101 series transceiver to be used with the SCU-LAN10 Interface: - MAIN: V01-14 - DISPLAY: V01-06 - IF DSP: V01-05 - SDR: V02-03 To confirm the firmware version on your FTdx-101 series transceiver, press [FUNC] key, touch [EXTENSION SETTING] and then select [Soft Version]. The software version will be displayed. All FTDX10 versions are supported. Each SCU-10LAN unit includes a special 13-pin DIN interface cable, a USB cable and two snap-on ferrite RFI suppressors. Specifications: Supply Voltage: 13.8 VDC Nominal Operating Voltage: 9 VDC to 15.2 VDC Current Consumption: 800 mA (max) Operating Temp Range: +32F-122F (0C to 50C) Dimensions: (WHD) 4.37 x 1.24 x 5.31 in. (111 x 31.5 x 135 mm) Weight: 0.93 lbs. (420g) NOTE: * A wired LAN port Ethernet router connection is required. Wi-Fi is not supported. * When using the internet, a fixed global IP address or fixed domain name is required for the network where the remote controlled radio is installed. Equip your Yaesu FTDX-101MP, FTDX-101D or FTDX10 transceiver for Internet LAN remote control operations with the Yaesu SCU-LAN10 Network Remote Control interface unit from DX Engineering.
( 5 )
$447.99
Yaesu Rotator Units
Yaesu Rotator Units are available as replacements or as stand-alone azimuth positioners for use with a third party controller. They include only the top mast bracket and hardware. Lower mast brackets are sold separately.
( 19 )
$329.99
—
$769.99
Yaesu 40M-WP Connector Kit for Yaesu Rotators
Yaesu 40M-WP Connector Kit for Yaesu Rotators includes the necessary connectors to repair or build a new Yaesu Rotator control cable for your rotator installation. The 6 pin Molex connector is for the control unit and the 7 pin round connector with a weatherproof cap is for the rotor. (Control cable not included) - Please CLICK or TAP on the title of a listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation.
( 3 )
$59.99
Yaesu Rotator Absorber Joint Mounts
Yaesu Rotator Absorber Joint Mounts are used between Yaesu rotators and tower mounting shelves to provide a cushion to the shock of torque on large antenna rotation systems.
( 3 )
$149.99
—
$159.99
Yaesu ATBK-100 Antenna Base Kits
Yaesu ATBK-100 Antenna Base Kits are accessory coil-loaded radials for the ATAS-120A Auto Active-Tuning Antennas to provide VHF and UHF operation when the antenna system is used portable, when not mounted on a vehicle. This base kit is not intended for mobile operation.
( 3 )
$115.99
Yaesu ATAS MICRO Manually Tuned Portable Antennas
Yaesu ATAS MICRO Manually Tuned Portable Antennas, model ATAS-25 is designed to for use with portable radios in the field. It can be mounted on a standard camera tripod 1/4 in. stud. It is manually tuned by sliding a shorting ring on the loading coil up or down and by selecting the correct number of top sections. Counterpoise wires are also provided. The ATAS-25 is constructed of high-grade materials for maximum efficiency, so it's the perfect traveling companion for you portable HF radios. Order Yaesu ATAS MICRO Manually Tuned Portable Antennas from DX Engineering.
( 6 )
$289.99
Yaesu Mast Adjustment Plates
Yaesu Mast Adjustment Plates are shims to use along a mast that is smaller than the rotator upper mast clamp.
( 11 )
$24.99
Yaesu Rotator Computer Controllers
Yaesu Rotator Computer Controllers are interface devices that link your Yaesu Rotator Controller to your computer via RS-232 (COM) connection. These units include the interface cables for the connections to the rotator controller and a PC serial port. Yaesu Rotators that support this computer interface are models G-2800DXA/DXC, G-10000DXA/DXC, G-800DXA and G-5500 rotators. Automation of directional antenna positioning is possible with Yaesu Rotator Computer Controllers.
( 2 )
$749.99
Yaesu G-5500 Series Rotator Replacement Mounting Hardware
The Yaesu Azimuth Rotators may be mounted at the top of the mast together with the elevation rotator, or separately inside a supporting tower. Mounting the Azimuth Rotators separately on the side of the mast requires additional hardware not supplied with the G-5500 Rotator kits. These YSU-S8003450 Pipe Clamps and YSU-S8002738A M8 X 115mm Stud Bolts (sold separately) are replacements for those originally supplied in the Yaesu Separation Kit. Refer to the installation instructions for the Yaesu G-5500 Series Rotators for more information.
Not Yet Reviewed
$2.19
—
$8.99
Yaesu Handheld Replacement Antennas
Yaesu Handheld Replacement Antennas are the original "rubber ducks" that are supplied with the HT. They are designed specifically for optimum performance of the Yaesu handheld for which it was designed. These flexible antennas are OEM replacements from the manufacturer of the radio to provide proper performance, every time. Order your Yaesu Handheld Replacement Antennas here, from DX Engineering.
( 1 )
$29.99
Yaesu AAA67X021 Replacement Rotator Controllers
Yaesu AAA67X021 Replacement Rotator Controllers keep your antenna turning after controller failure. These controllers are direct replacements for the G-2800DXA, G-1000DXA or G-800DXA rotator systems. These replacement desktop controllers feature a 360 degree radial indication of the actual antenna bearing azimuth. These modern DC controllers support the selection of rotating speeds from 40 to 100 seconds per rotation (360 degrees) for either the G-800DXA or G-1000DXA, or 50 to 120 seconds per rotation (360 degrees) for the G-2800DXA, and can preset a desired heading for the rotator, to which it then turns automatically. With the G-2800DXA, when a fast rotating speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the end-of-rotation heading (the compass bearing through which the rotator cannot be turned) most convenient for his location and operation, allowing full rotation through north, south, or both, if desired. In any case, 90 degrees of overlapping rotation allows rotation through the selected stopper heading (450 degrees total rotation). Need a replacement controller for your Yaesu rotator? Order a Yaesu AAA67X021 Replacement Rotator Controller from DX Engineering!
Not Yet Reviewed
$659.99
Yaesu Replacement Rotator Controllers
Yaesu Replacement Rotator Controllers available here are direct replacement for the G5500, G-450A and G-450ADC models. These are only controller replacements which do not include rotator motors.
( 1 )
$209.99
—
$419.99
Yaesu YA-30 Broadband HF Folded Dipole Antennas
Yaesu YA-30 Broadband HF Folded Dipole Antennas are compact folded dipole antennas. YA-30 Folded Dipoles not only cover 1.6 to 30 MHz, they handle RF power input of 150W PEP. Best of all, as with the majority of broadband antennas, no antenna tuner is required. These folded dipoles are multi-wire but relatively light in weight. By having only two stainless steel wires they have little wind loading and an SWR of better than 2:1 on 1.6 to 18 MHz, and 3:1 above 18 MHz. Yaesu YA-30 specifications: * Frequency Range: 1.6-30 MHz * Input Impedance: 50 Ohms * Power Input: 150W PEP (voice) for 3-30MHz * Power Input: 75W (AM, FM, Data, RTTY) TX five minutes maximum 20 percent duty cycle * Input Connector: UHF-type socket * Antenna Length: 83 ft. * 55 ft. inverted "V" configuration (with a 35 ft. tower) Special features: * No Tuner required * UV resistant spacer rods * UV resistant balun * Stainless steel wire * Supplied with 100 ft. of coaxial cable You've heard of the renowned Yaesu quality. If you would like a broadband antenna for 160 through 10 that will last the test of time, then look at one of these Yaesu YA-30 Broadband HF Folded Dipole Antennas from DX Engineering!
( 2 )
$349.99