Filters
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems
Yaesu G-2800DXA Extra Heavy-Duty Rotator Systems are azimuth positioners designed to rotate large tower-mounted amateur and professional antenna arrays under remote control from the station's operating position. These systems feature attractive compass-dial position indication controllers, with a connector port for optional computer interface for automated directional antenna positioning control. Yaesu's G-2800DXA rotator design utilizes 98 heavy 3/8 in. dual-stacked circumferential ball bearings to distribute load over the full diameter of the housing. This design minimizes stress and wear and practically eliminates the possibility of destructive water entry: There is no shaft hole in the top of the housing. Instead of the usual AC motor drive used in older rotator designs, the G-2800DXA, G-1000DXA and G-800DXA use a variable-voltage DC motor, removing the need for a large starting capacitor with its potential for failure exposed to outside temperature variations. The factory-lubricated rotator unit is housed in melamine resin-coated die-cast aluminum, intended to provide maintenance-free operation under all climatic conditions. A mast alignment gauge on the rotator housing simplifies accurate mechanical alignment during installation. Tower mounted, this model handles over 30 sq. ft. of antenna wind load and over 650 lbs. of vertical mast load. About 130 ft. of control cable is included with the G-2800DXA only. Control console power is 110/120 volts AC. The handsome desktop controller provides 360 degrees radial indication of actual antenna azimuth bearing. You can select rotation time over 360 degrees from 50 to 120 seconds on the G-2800DXA, and preset a desired heading for the rotator, to which it then turns automatically. When a fast rotation speed is selected, special "auto slow-start" and "auto slow-stop" features avoid sharp jolts to the antenna array and tower. Activating the rotator causes it to begin turning at slow, but increasing, speed. As the antenna approaches the desired heading, the rotation automatically slows down, before bringing the antenna to a gentle stop. The operator may select the stop heading, the compass bearing through which the rotator cannot be turned, which is most convenient for their station location and operation, allowing full rotation through north, south or both, if desired. In any case, 90 degrees overlapping rotation allows rotation through the selected stop heading for 450 degrees of total rotation. These rotators are intended for mounting to an accessory shelf inside a support tower (not supplied), at least 1-meter (40 in.) below the top of the tower. Yaesu rotators have a fine reputation within the Amateur Radio community. When installing a new tower, or replacing an old rotator, consider purchasing a Yaesu G-2800DXA Extra Heavy-Duty Rotator System from DX Engineering.
( 1 )
$1,769.99
Instant Rebate
Yaesu FTX-1 Series HF/50/144/430MHz SDR All Mode Base/Portable Transceivers
Yaesu FTX-1 Series HF/50/144/430MHz SDR All Mode Base/Portable Transceivers provide continuous wide-range RX coverage from 30kHz through 174MHz, and from 400 through 470MHz including SWL, FM broadcast, and Air-band. TX band coverage includes HF 160 – 10M, with the addition of 6M, 2M, and 70cm. The Yaesu FTX-1 Field is perfect for portable field operation. This model features up to 10W of power output when used with an external 13.8VDC power supply. By attaching the SBR-52LI Li-ion to the rear of the Field Head, the FTX-1 provides 6W (5W for QRP) stand-alone operation on HF through V/UHF bands in all modes – SSB, CW, AM, FM and C4FM digital. 9-hour stand-alone operating time with 6W on HF bands (SSB), and 8-hour operating time with 6W on V/UHF bands (FM) are available (6-6-48 duty cycle). The FTX-1 Field Head can charge the included Li-ion battery automatically when connected to an External 13.8VDC power supply or use an optional third-party USB Type-C PD (Power Delivery) cable to recharge the battery (45W or greater/ 15V 2A).
( 19 )
$1,549.95