Availability
Receive Antennas and Arrays
DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas
New Name...Same Antenna! DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas are designed for low-noise reception of signals within the frequency range of 100-kHz to 30-MHz. Their integral, extra-high dynamic range, low-noise preamplifier is designed for minimum intermodulation distortion in the presence of very high-level signals that would normally overload most preamplifiers. Read more about the exclusive Clifton Laboratories design of the loop's RF-30 preamplifier by clicking "More Details" below. RF-PRO-1B Active Magnetic Loop Antennas, formerly known as the "Pixel Loop" and recently as InLogis, are now manufactured and serviced by DX Engineering. For Amateur Radio operators, AM DXers and Short-Wave Listeners, these active loop antennas are a great way to extend your listening ability. Add DX Engineering RF-PRO-1B® Active Magnetic Loop Antennas to your radios and start hearing more signals with less noise! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 25 )
$809.99
DX Engineering NCC-2 Receive Antenna Phasing Systems
Imagine adjusting the controls to knock out strong interfering stations or noise—and then being able to copy and log that weak DX station. By successfully combining the right antennas with the advanced phasing capabilities of the NCC-2, this is the operating thrill that every radio enthusiast can enjoy, again and again! DX Engineering NCC-2 Receive Antenna Phasing Systems are variable phasing controllers that combine the 300 kHz- 30MHz received signals from one transmit antenna and one receive antenna, or from two dedicated receive antennas. Combining signals from two stationary antennas physically spaced 1/10 to 1/2 wavelength apart creates an array pattern with signal peaks and dips called nulls. Adjusting the NCC-2 Phase and Balance controls have the effect of electronically rotating or steering that pattern. Steering the null direction to significantly weaken a local or distant interfering signal or noise is known as "Noise Cancelling." This "Noise Cancelling Controller" (NCC-2) can dramatically enhance the reception of weak signals from non-null directions. This "reverse-beam" capability on radio frequencies AM Broadcast through HF can provide amazing benefits for many types of AM DX and SWL receiving and ham radio operating. Work new DX, hear the weak station in casual regional conversations, snag the rare multiplier in contests and hear beyond the noise and interference in dire circumstances. DX Engineering NCC-2 Phasing Systems now feature the built-in RTR Receive-Transmit Interface relay system that expands the exciting benefits of antenna phasing for interference reduction in two ways: * First, the NCC-2 can combine signals from the HF transmit antenna and a separate receive antenna to effectively notch-out strong stations or noise. Almost any Amateur can now enjoy the benefits of antenna phasing and noise-nulling, even those with space limitations for separating the receiving and transmitting antennas. * Second, the user of any standard HF transceiver that lacks a separate receive antenna input can have enhanced reception of noise and signal nulling with the DXE-NCC-2 and two antennas. Rear panel SO-239, F and BNC connectors make the NCC-2 extremely versatile and easy to connect to almost any receiver or HF transceiver up to 200 watts. Redesigned with plug-in modular circuit board sockets, the NCC-2 includes one switched and powered internal slot and two passive internal slots per channel to accommodate these new options: * DXE-RPA-2-PM Receive Preamplifier Plug-In Modules (powered): one per channel for low-signal passive antennas with poor ground conditions * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-In Module (passive): Front-end protection for the NCC-2 and the receiver * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-In Module (passive): to match 75 ohm RX ANT feedlines to NCC-2 50 ohm internal impedance * NCC-2 Receive Filter Sets (passive, non-switchable): High Pass, Band Pass and Low Pass Filters for 160, 80, 40 meters typically in stock, with other band filters available individually by special order. DX Engineering NCC-2 Receive Antenna Phasing Systems offer these new additional benefits: * Multi-Color Status Indicating LEDs for Power, RTR Mode and Preamp Power CH A and CH B * New Radio Key Line Input with RX Enable Output-RTR Failsafe to prevent RF damage to NCC-2 and RX equipment * New ACC Key Line Output RCA female 'ground on transmit' pass-through for Amplifier or Accessory * New screw-on 2.1mm DC connector to prevent accidental power cable pull-out * Operates on +13.8VDC @ 2A input to power the NCC-2 and internally jumper set Bias Tee on each RX ANT ports for coax fed Active Verticals and other accessories. Offering new and experienced radio enthusiasts the next level of reception enhancements, DX Engineering model NCC-2 Receive Antenna Phasing Systems in use around the world!
( 19 )
$955.99
DX Engineering Receiver Guard Electronic RF Limiters
DX Engineering Receiver Guard RG5000HD Electronic RF Limiters are the best choice of inline devices to protect your receiver antenna inputs. The Receiver Guard is a receive antenna input limiter specifically designed to protect a sensitive receiver front-end against high levels of RF and potential damage. At the heart of each Receiver Guard is a highly effective electronic RF limiter covering 500 kHz to 150 MHz with an insertion loss under 0.15 dB up to 50 MHz and under 0.30 dB up to 150 MHz. The multi-stage design includes a gas discharge tube for maximum pulse energy protection. The DXE-RG5000HD rejects 10 watts of catastrophic receive antenna feedline RF while passing a maximum signal of about 87 dB over S-9, which is only 25 mw, a signal level that is well below the point of front end damage. Receiver Guards are a must for multiple radio contesting stations and they provide low-cost front-end "insurance." Use them in these common high-RF situations: - Receive antennas in very close proximity to transmit antennas - Field-day operations with many transmitters in close range - Multi-transmitter contesting sites - Neighboring Amateur and CB operators - Frequent high-power mobile encounters Extensively tested and proven in real-world stations, the Receiver Guard works for all radios and offers the ultimate performance required by the upper tier of transceivers tested to have the best narrow-spaced third-order dynamic range or published RMDR (Reciprocal Mixing Dynamic Range). These are passive electronic limiters, so competitive contesting stations use separate band filters in addition to the Receiver Guard. When there are high levels of RF on your receive antennas, the DX Engineering Receiver Guard generates far less harmonic noise than other limiters on the market, which allows your station to continue to operate safely and competitively. At normal HF signal levels the RG5000HD operates continuously with no effect on the performance of your station while providing the best possible protection for your radio. Here are key Receiver Guard features: * Keeps stray high levels of RF from damaging your receiver input * Ideal for separate 160 and/or 80 meter receive systems with large pulse and RF energy capture area * Uses state of the art components for maximum protection of receivers * Under 6 ns response time * Multi-Stage protection * Very low insertion loss * Uses BNC type connectors to avoid accidental connection to a transmit feedline * Has been developed and tested in world-recognized multi-multi contest station K3LR Specifications - DX Engineering Receiver Guard model DXE-RG-5000HD - Frequency Range: 0.5 through 150 MHz - Insertion Loss: < 0.15 dB up to 50 MHz, < 0.3 dB 50 MHz up to 150 MHz - VSWR: < 1.2:1 - Maximum Output Level at 10 W input: +14 dBm (0.025 W) - Maximum Power Handling: 10 W CCS (Continuous Commercial Service) - Device Impedance: 50 to 75 ohms, unbalanced - Connectors, Input and Output: BNC female Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. What happens if the receive antenna is extremely close to the transmit antenna, or there is an antenna support or other system failure that causes a high RF level to enter the receive antenna input? A DX Engineering Receiver Guard can save the day! Order yours now.
( 33 )
$105.99
DX Engineering Receive Short Element Active Vertical Antennas
DX Engineering Receive Short Element Active Vertical Antennas (the RSEAV Antennas) offer excellent low noise radio frequency reception from 40 kHz to 30 MHz. Better receiving performance than full-size transmit antennas and other active makes the DXE-RSEAV-1 the best choice on the market for VLF through HF reception, including long-distance AM broadcast, Medium Wave and Shortwave (SWL), and new low-frequency Amateur bands, DXing, contesting, and everyday HF operations. Click on a listed product title and Scroll Down to see additional important information. A complete product description appears below the Specifications Overview. Instruction manual links appear in the Documentation section. The sleek and stealthy DXE-RSEAV-1 includes a high-quality three-section 8.5 ft. (2.6m) aluminum tubing whip, insulated mounting plate and the completely new DXE-AVA-3 Active Matching Unit. Its state-of-the-art broadband operational amplifier design works as a high-impedance buffer between the short antenna element and RG6U 75-ohm coax. When installed in the appropriate location, RSEAV antennas provide significantly better weak signal reception than other active receive antennas and full-size transmit-capable antennas, with substantially reduced noise and lower spurious signal interference. Receive Short Element Active Vertical Antennas are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. They are sold individually (DXE-RSEAV-1), or with a bias tee (DXE-RSEAV-1FVI) and DXE-RSEAV-1 Receive Short Element Active Verticals set a new standard for "Active Receive Vertical Antennas" replacing legacy DXE-ARAV-3, ARAV-2, ARAV-1 and AL-24 versions. Use multiple DXE-RSEAV-1 for all 4 and 8 element DX Engineering Receive Arrays – all 3, 4 and 8 element Hi-Z Antennas Arrays – and 2 element receive arrays with DXE-NCC-2 and NCC-1 Variable Phasing Controllers. The DXE-RSEAV-1 is designed to be a very low-gain, low-noise antenna for greatly improved signal-to-noise performance over a very wide range of frequencies. In a proper single or multi-element array installation, this Receive Vertical antenna will attenuate high-angle skywave signals, which is the goal for a low band DXing receive antenna. Low-angle, long-range DX signals are easier to copy with a good radio and DX Engineering Receive Short Element Active Vertical Antennas. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace or upgrade all the elements in the array with identical, fully compatible DXE-RSEAV-1 antennas or DXE-AVA-3 units.
( 3 )
$249.99
—
$1,999.92
WiMo QRM Eliminator
The WiMo QRM Eliminator is a simple signal phasing device that can effectively reduce or remove noise interference for dramatically improved reception from 3.5 to 60 MHz. The QRM Eliminator is based on a totally innovative concept and cannot be compared to the performance of noise blanker or DSP circuits. Removing the noise before it gets to the receiver is the superior method of interference reduction. With the WiMo QRM Eliminator you can get rid of local interference almost entirely, up to an S9 level, with the likely result of completely clear reception! You don't have to understand the cause or type of interference nor do you need to know the location of its source. It doesn't matter if the interference originates from your own station or from a welding unit hundreds of feet away. The QRM Eliminator simply connects to the antenna port of transceiver and to the antenna (or amplifier input), without any radio modifications required. An additional user supplied auxiliary receiving antenna is required, such as a properly positioned 8 ft. outdoor dipole antenna or a simple 20 ft. wire in the shack, for example. This "noise sense" antenna receives mostly unwanted signal, while the transmitting antenna receives the same interference in a different phase along with the desired signal. The QRM Eliminator allows the adjustment of the amplification and phase to cancel out the unwanted signal before it reaches the receiver front end! Noise or interference nulling can provide over 45 dB of unwanted signal suppression, in many cases resulting in clear reception of the desired signal. The QRM Eliminator is built into a shielded metal enclosure, functions over the frequency range of 3.5 through 60 MHz, and has a status LED to indicate when the unit is turned on for phasing. The unit has a built-in T/R relay with PTT control via a rear panel RCA phono connector for the transceiver amplifier keying line. The QRM Eliminator automatically switches the Main antenna connection to the transceiver during transmit. Also, simply turn the unit off to bypass the phasing unit for normal reception on the Main transmit antenna. Click "More Detail" below to see additional information about this exciting device. You may not believe the power of interference phase nulling until you have experienced it for yourself. Order the WiMo QRM Eliminator exclusively in North America from DX Engineering.
( 25 )
$229.99
DX Engineering RTR-2 Modular Receive-Transmit Interfaces
DX Engineering RTR-2 Modular Receive-Transmit Interfaces provide the easiest and safest method for connecting a dedicated receive antenna to an HF transceiver that does not have a separate receive antenna input. Placed inline with the transceiver's antenna connector, the RTR-2 does the job of a 200 watt T/R relay using the amplifier keying line for failsafe protection, so your transmitted energy cannot go to the receive antenna. Three internal Plug-in Module option slots provide added features and protection: * DXE-RPA-2-PM Receive Preamplifier Plug-in Module * DXE-TRI-PM Transmit Receive Interrupter Plug-In Module * DXE-IT-PM 75 to 50 ohm Impedance Transformer Plug-in Module DX Engineering RTR-2 Modular Receive-Transmit Interfaces allow the standard transceiver owner to enjoy the advantages of separate receive antennas. For the unswitched receive antenna (RX ANT) port on expensive transceivers, the RTR-2 interface also adds inexpensive failsafe protection. The receive antenna line can be opened or grounded with the optional DXE-TRI-PM Interrupter plug-in module. The RTR-2 is a very useful device for many applications, including: * Connection of external receiving antennas to transceivers lacking external antenna ports * T-R antenna switch for older equipment using separate transmitters and receivers * Interfacing antennas to older phasing or noise cancelling systems * Addition of a switchable receive preamplifier to any transceiver or transmitter and receiver combination * Excellent failsafe receiver protection for close-spaced transmit and receive antennas, without performance degradation of diode circuits of other devices. RTR-2 units feature a unique, failsafe connection method that prevents the hot switching and timing errors that are common on other transmit/receive relays. RTR-2 interfaces switch fast enough for partial break-in CW operation. There are many simple applications for the new RTR-2 and now internal modules can add dramatically improved reception of those really weak signals on the crowded HF bands! DX Engineering RTR-2 Modular Receive-Transmit Interfaces enable operators to enjoy improved reception with any low noise receiving antenna system. This shielded enclosure relay system provides a safe method of connecting a receive antenna, such as a Beverage, Active Receive system, or other receiving accessories to your radio. Major features that make the DX Engineering RTR-2 Receive Antenna Interfaces your best choice for a receive T/R system device: * New Status Indicating Color-changing LEDs * Three internal slots for new DX Engineering modules * New Key Line Out connector for Amplifier * New internal jumper for placing DC on the Receive Antenna feedline for Active or Loop receive antennas * Attractive and heavy stainless steel enclosure * 200 watts RF switching capability * Supports CW partial break-in * Main transmit antenna connector is SO-239 (UHF female) * Radio RF connector is SO-239 (UHF female) * Receive antenna input is 75 ohm F connector * Receive outputs are standard 75 ohm Type F connectors * Inputs are 50 ohm BNC or 75 ohm F (Optional transformer module available) * Safe switching--transmit antenna is always connected to transceiver on power-off * Hot switching lockout--disables receive antenna during transmit mode (Optional DXE-TRI-PM can be set to short the RX ANT line) * Versatile--allows inclusion of Optional RF preamplifiers and other plug-in modules * Simple 13.8 Vdc input for all operations An indispensable accessory for the DX enthusiast and useful for any Amateur's shack, DX Engineering RTR-2 Modular Receive-Transmit Interfaces can help you expand and improve your station's antenna connections and the protection of your equipment.
( 12 )
$375.99
QuietRadio Aziloop DF-72 Multi-Directional Receive Antenna System
The QuietRadio Aziloop DF-72 Multi-Directional Receive Antenna System is an innovative, low-noise solution for VLF to HF reception. This dual-mode, electronically rotatable HF receive antenna system features a primary frequency range of 20 kHz to 10 MHz, with coverage to 30 MHz at reduced directivity and sensitivity (determined by antenna size). Additionally, it can be fed with a single coaxial cable, eliminating the need for bulky antennas and rotators.
( 1 )
$779.99
QRO.cz RX Audite SDR Antenna Switch Controllers
QRO.cz RX Audite SDR Antenna Switch Controllers combine the functionality of a T/R switch, a receive antenna input and a receive splitter with specialized switching, all with RF limiter protection. The transmit/receive (TX/RX) main antenna can be shared with both outputs, transceiver and receiver (SDR) with RF power limiter protection. These versatile devices are perfect for use with a separate SDR receiver for Spectrum Panadapter, WebSDR or as a Skimmer Server to contribute spots to the Reverse Beacon Network (RBN). The RX-Audite features frequency coverage of 100 kHz–60 MHz including 160 through 6 meters with a maximum transmit power handling of 200W. Included in the Package: RX-Audite Switch – Assembled and Tested DC Cable – DC barrel connector to stripped and tinned wires
( 5 )
$329.99
—
$509.99
DX Engineering Plug-in Modules
A new series of Plug-in Modules are available specifically for new DX Engineering devices that accept them. Details on each module are found at each part. DX Engineering Plug-in Modules include: * DXE-RPA-2-PM Receive Preamplifier Plug-in Modules * DXE-RG5000HD-PM Receiver Guard 5000HD Plug-in Modules *DXE-IT-PM 75 to 50 ohm Impedance Transformer Modules Modules for High Pass and Band Pass Filter Plug-in Modules are coming in 2017. These new Plug-in Modules are optional devices for the following new DX Engineering devices: * DXE-NCC-2 Receive Antenna Phasing Systems * DXE-RPA-2 Modular Receive Preamplifiers * DXE-RTR-2 Modular Receive-Transmit Interfaces * DXE-DMC-2 Dual Module Chassis Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Discover new ways to equip your world-class station with DX Engineering Plug-in Modules for your DX Engineering devices. Click below on More Details to learn more!
( 17 )
$35.99
—
$80.99
DX Engineering AVA-3 Active Matching Units
DX Engineering AVA-3 Active Matching Units are state-of-the-art broadband receive RF operational amplifiers that achieve unparalleled weak signal reception across the radio frequency range from 40 kHz* to 30 MHz. They work as a high impedance buffer between a short antenna element of 6 to 24 feet and an economical 75 ohm feedline. The AVA-3 and a short element are intended to be mounted on a ground rod at ground level in a clear area away from all metal, towers and other antennas. The gain adjustable AVA-3 is the sole upgrade and drop-in replacement for all discontinued receive array element amplifiers including Hi-Z Antennas AMP, PLUS6-AMP, AMP-V2 and AMP-PLUS-V2 as well as DXE-AVA-2 and AVA-1. The DXE-AVA-3 Active Matching Unit is the heart of the new line of DX Engineering Receive Short Element Active Vertical Antennas, DXE-RSEAV-1. Compared to large antennas, this amplified short element method dramatically improves signal-to-noise performance for excellent VLF, LF and HF weak signal reception. Click or tap the title of the listed item for an overview - a complete description, Specifications, Required and Suggested Parts. Links to instruction manuals and charts appear in Documentation. The AVA-3 Active Matching Unit provides these features and benefits: • Ultimate frequency coverage of 40 kHz* to 30 MHz for VLF through HF (including the 2200m and 630m Amateur bands) • High Third Order Intercept (TOI) Performance +39dBm for superior strong signal handling equal to top transceivers • Consistent unit to unit gain for greatly improved array performance • Virtually Flat Gain (+/-0.4 dBm) across the entire frequency range • Internally settable gain (default -6, 0, or +6 dBm) for different ambient noise locations and element sizes • Direct DC via second F connector – internal settable choice for separate DC and RF coaxial cables for best performance, or standard Bias Tee DC on the RF coax • Each DXE-AVA-3 Active Matching Unit operates on 12 -15 VDC at 25mA • Element is grounded when power is removed • 75 ohm F connectors support field serviceable RG-6 Quad Shield suitable up to 1,000 feet for VLF through HF *Frequency coverage below 200 kHz requires Direct DC on a separate DC only coaxial cable. Please Note: To achieve the expected reception pattern, multi-element phased arrays depend upon identical gain and phase response from each element. Every individual element amplifier, its grounding, and even its feedline characteristics and length, must be identical to the others in the array. Therefore, when unrepairable failures occur, it is essential to replace and upgrade all the element amplifiers in the array with fully compatible DXE-AVA-3 units.
( 5 )
$139.99
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit
DX Engineering NOISELOOP Portable Receive Flag Antenna Kit is based on the design by Don Kirk, WD8DSB. Don's article on this antenna is published in the March 2021 issue of QST Magazine (used by permission). The DXE-NOISELOOP is a kit of parts to build this receive-only portable directional HF loop antenna, which measures only 48 by 24 inches plus 36 inches of mast-handle. It may be used while walking or stationary with your portable HF receiver. Oriented vertically, this loop antenna features a cardioid pattern at the horizon with a deep null of up to 30 dB rejection. It is an excellent tool for locating noise sources from 1.8 through 30 MHz and for low-noise, general coverage reception from the AM broadcast band through 30 MHz. An optional Preamplifier-Attenuator Unit, DXE-NL-PRE-ATT-1, may be attached to the loop mast handle for enhanced operations. An IC-705, a portable SW or a handheld HF receiver are excellent choices for searching for local noise sources with the NOISELOOP, around the neighborhood and even around your own home. This Portable Flag Antenna Kit includes everything needed to make the antenna: fiberglass tubing for the frame and handle, mounting plate, separate PC boards for the bifilar wound transformer and load resistor, antenna wire, coaxial cable with male BNC and stainless steel hardware. Simple hand tools and a solder iron are required for assembly. Included instructions detail assembly. This kit will typically take between 1 and 2 hours to build. The WD8DSB Portable Flag Antenna design has become a real game changer in direction finding of RFI on MF and HF frequencies, and you will also find it an invaluable tool when hunting RFI due to the following key features. *Unidirectional (unlike a tuned loop) *Broadband (unlike a tuned loop, excellent for AM DXing, SWL and Amateur) *Portable (easy to walk with while directional noise finding or HF Fox Hunting) Traditionally Flag antennas are large and designed for stationary use, but the idea for this antenna was to design a Portable Flag. It was designed to be the largest possible (to maximize gain) that would fit inside a car and it's still small enough to maintain a cardioid pattern up through 30 MHz. The portable Flag has an approximate dimension of 2 feet tall by 4 feet long which you (or a helper) can easily walk with while tracking down a signal. Unlike a tuned loop, the Portable Flag is a broadband antenna with unidirectional properties, and it's designed for direction finding from 1.8 to 30 MHz as long as an appropriate preamp is used. It's even useful for direction finding down in the AM broadcast band. The rear of the antenna produces a sharp null when pointed at the signal of interest and the sharp null is often used for direction finding versus using the broad peak which occurs when the front of the antenna is pointed at the signal of interest. Learn more about how to build this antenna kit by clicking on More Detail and the Documentation link for the Instruction Manual. Order your DX Engineering NOISELOOP Portable Receive Flag Antenna Kit here.
( 15 )
$159.99
DX Engineering Beverage Antenna Systems
DX Engineering Beverage Antenna Systems are single-wire, single-direction beverage feed systems. Their W8JI design makes them immune to the strong signal overload and core saturation common in multi-transmitter contesting environments. They are used by winning contest stations and low-band DXers. They use an isolated-winding matching-transformer system to significantly increase the signal-to-noise ratio in Beverage and other high-impedance antennas. Now RoHS-compliant, they will work with antenna impedances from 400-500 ohms. The termination resistor included is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes significantly better than hard-to-find carbon composition resistors. Features include: * 100 kHz to 30 MHz operating range * Spark gaps minimize damage from lightning * Wing nut terminals eliminate soldering * Rugged aluminum housing and stainless steel hardware * Flange-mount holes for easy mounting * Ground isolated secondary can be connected with normal or reverse phase Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. Beverage antennas have been in use since the 1920s. These DX Engineering Beverage Antenna Systems modernize the Beverage concept for convenience and performance.
( 20 )
$115.99
DX Engineering High CMI Receive Feedline Chokes
DX Engineering High CMI Receive Feedline Chokes achieve exceptionally high isolation between the input and output connector shields to effectively block common-mode RF noise and unwanted signals that collect on 50 or 75 ohm receive antenna feedlines. Ongoing research and development by the design team at DX Engineering has produced two bidirectional Receive Feedline Chokes; a 50-ohm model with BNC female connectors and a 75-ohm model with Type-F female connectors. Both chokes cover the RF frequency range 100 kHz through 30 MHz. They exhibit very high common mode impedance* (CMI typically over 8,000 ohms across the 160, 80, and 40 meter bands) and feature DC pass capability up to 700 mA at 13.8VDC, with extremely low SWR and negligible insertion loss. Affordable DX Engineering High CMI Receive Feedline Chokes will be considered the best, most versatile receive chokes ever produced for typical low band receive antenna applications.
( 2 )
$59.99
—
$64.95
DX Engineering RF PRO Loop Replacement Components
Since DX Engineering manufactures the RF-PRO-1B® Active Magnetic Loop Receive Antenna, we can offer these RF PRO Loop Replacement Components. Available for refurbishing Pixel, InLogis or DX Engineering Active Magnetic Loops, choose one or more of these individual "Original Equipment" components, component set or handy accessory pack that fills your needs. 1. DXE-RFPRO1B-PA Receive Preamplifier has this new part number for the preamp unit only. This is the weatherproof, metal-encased replacement RF PRO 1B Receive Preamplifier that mounts directly onto the loop bracket. Mounting hardware is not included with this replacement low-noise preamp, but it is available in the… 2. DXE-RFPRO1B-OAP Outdoor Accessory Pack. This package contains the insulated shoulder washers, flat washers and nuts to properly mount the preamp. Also included in this outdoor package for the loop installation are the mast mounting V-Bolts and Saddles and the short RG-6 F connector jumper to connect the loop to the preamp, and weather sealer. User supplied RG-6 coaxial cable is used for the long feedline that is run inside to the… 3. DXE-RFPRO1B-PI Power Inserter. This is the indoor unit that puts a well filtered and regulated 20 Vdc power onto the feedline for the preamp. It carries the loop RF to the receiver via the F connector. This unit also disables the power to the preamp when it is keyed by the transceiver amplifier keying line. The Power Inserter is run on 24 Vac from the… 4. DXE-PSW-24A-6AU AC Adapter. This clean power supply is a linear transformer that converts 120 Vac to the 24 Vac at 600 mA required by the Power Inserter. It is has the attached 2.1mm power connector. 5. DXE-RFPRO1B-IAP Indoor Accessory Pack contains the cables and adapter to connect the transceiver RF and keying lines to the Power Inserter. The F connector coaxial cable connects RF from the Inserter to the radio. A supplied F female to PL-259 adapter facilitates that connection, should you radio need it. An RCA phono patch cable is supplied for keying the Power Inserter and a RCA phono y-adapter provides the additional keying line connection for a power amplifier. 6. DXE-RF-30B Complete Component Package is for a system replacement where only an existing RF PRO 1B Loop is available. All of the above individual components, cables and hardware items listed above, items 1 through 5, but not the loop, are included in this DXE-RF-30B package. 7. DXE-PRO-LOOP is the Replacement RF PRO 1B Loop that is ordered by customers who have all other components of their system working. When your damaged or defective loop needs to be replaced, this is the loop only part to order. RF-PRO-1B® Loops may occasionally need a replacement component or hardware package. DX Engineering RF PRO Loop Replacement Components are available right here, at DX Engineering!
( 9 )
$17.49
—
$464.45
Unified Microsystems BevFlex-4X and BevFlex-4X/Q Reversible Receive Antenna System
Unified Microsystems BevFlex-4X Reversible Receive Antenna System is a very versatile two-direction low band receiving antenna. This is the updated and improved version of the W8GNM revolutionary design that uses only low cost, low loss RG-6 for the elements and the feedline of a Reversible Beverage antenna or Reversible Beverage on Ground antenna. Plus, it uses specially designed transformer units that allow the feedpoint unit to be placed anywhere along the length of the Reversible Beverage or BOG, instead of only at one end or the other. Like for other Beverage antennas, the Elevated Beverage or a Beverage on Ground (BOG), the performance of the reversible BevFlex-4X system depends upon the length of the user supplied RG-6 coax for the antenna element. Also, the versatile BevFlex-4X components may be used to create a two-direction version of any one of these antennas, using a much shorter length of wire for the receiving element: * EWE * Flag * VE3DO Loop BevFlex-4X Systems consist of four components; one Feed Unit, two Terminator Units and one Control Switch Unit. The Feed and Terminal Units are house in NEMA rated enclosures and use stainless steel hardware for maximum weather protection. Do you need enhanced reception in four directions? The BevFlex-4X/Q combines two sets of Terminator and Feed Units with the RAS-4 remote antenna switch to let you hear better in all four quadrants. The BevFlex-4X antennas can be any mix of Beverage, BOG, Flag, EWE, or VE3DO. The included RAS-4 Remote Antenna Switch only requires a single coax and four wire control cable to the shack. NOTE: An in-shack four direction switch control box is not included. Choose a control console from DX Engineering, EA4TX and others, or build your own. Just add RG-6 coax and ground rods! Click "More Details" and the Brochure link at the Documentation tab to see pdf diagrams of all of these two and four-direction BevFlex receive antenna system connections. Depending upon the real estate you have available, the FAQ chart will help you choose the Unified Microsystems BevFlex-4X or BevFlex-4X/Q configuration that fits your property and your low band reception needs!
( 14 )
$349.99
—
$649.95
DX Engineering 2-Port Splitter-Combiners
DX Engineering 2-Port Splitter-Combiners are receive signal-level RF devices that operate from 300 kHz to 30 MHz, available in 50 ohm and 75 ohm versions. They're typically used to split one RF signal to properly feed two receivers, or the receive antenna inputs of one transceiver and one separate receiver. They also properly combine two receiving antennas in phase, such as Beverage antennas, to form a phased receive array. Important features of the DX Engineering 2-Port Splitter-Combiner: * Available for 50 ohm and 75 ohm systems * Broad, 300 kHz through 30 MHz operating range * High-quality components * Isolated ports * Metal housing for superior shielding and longer life * Reliable side-mount connectors: BNC female for 50 ohm, F female connectors for 75 ohm model * Economical solution to potential impedance errors that cause losses With the updated "SC" versions of the original 2-Port Splitter-Combiner, DX Engineering has maintained the port isolation design that prevents signal performance degradation caused by impedance errors in less-than-perfect receive systems. The normal signal level reduction when used as a splitter is just over 3 dB per port. As with any system, losses are dependent upon source and load impedances being matched. DX Engineering Splitter-Combiners provide equal power, voltage, and current to matched loads on ports 1 and 2. The primary advantage is that individual receiver input variations, or a band filter attached to only one port, will not seriously affect the signal level in the other receiver. In addition, any spurious signals generated in one receiver are greatly attenuated by the 2-Port Splitter-Combiner before reaching the second receiver. When splitting in-phase signals, the loss is somewhat less. Any unused port of the 2-Port Splitter-Combiner should be terminated and specified losses are based on source and load impedances being matched. The DX Engineering 2-Port Splitter-Combiner is a passive device; therefore it requires no power to operate. Use the 75-ohm version for combining two 75 ohm antenna feedlines into a single 75 ohm feedline with negligible loss; or use the 50-ohm version for 50-ohm antennas and feedlines. Examples for applications are for two antennas forming an in-phase (broadside) receiving array, a cross-fire Echelon Beverage array, or any type of array with fixed phasing. There are a number of advantages to using these units for combining antenna systems over a standard parallel connection: * Splitter-Combiners match the entire antenna system to the feedline impedance; conversely, paralleling feedlines by using a T-connector divides the impedance in half, causing mismatched losses * With antennas connected directly in parallel, if either one develops a high impedance open, becomes shorted, falls down, or has a feedline problem, the entire antenna system may become unusable. By using the 2-Port Splitter-Combiner, only the problem antenna is unusable; the antenna on the other port can still be used * Unlike quarter wave matching sections that only work on one band, these Splitter-Combiners have extremely wide bandwidth * Due to the built-in isolation and balancing, these units limit the signal loss to approximately 3 dB per port * 2-Port Splitter-Combiners provide very high isolation between ports 1 and 2; this prevents either antenna from interfering with the other during normal operation Note: These devices cannot be used for FM broadcast, VHF, UHF, CATV or Satellite TV. They operate only MF through HF. Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information.
( 3 )
$100.99
—
$107.99
Moonraker X1 HF Vertical Receive Antennas
Moonraker X1 HF Vertical Receive Antennas are ideal for those who want to listen to shortwave but have limited space to erect larger antennas. This antenna features helical wound, internally loaded wire traps that are a great alternative to a long wire and the RX capabilities range from 1-50 MHz without the need for radials. This antenna is easy to assemble and comes ready to mount to any mast up to 1.50 in. (not included). Additional Features and Specifications: * Antenna Height: 6.562 ft. (200cm) * Antenna Connector: UHF SO-239 * Mast Clamps (included) * RG-58 Coax Cable Assembly: 32.808 ft. (10 M) PL-259 to SMA (included)
( 3 )
$219.99
Hi-Z® Antennas PC-8PRO 8 Circle Array Phasing Controller
The Hi-Z Antennas PC-8PRO 8 Circle Array Phasing Controller is the primary component in the Hi-Z Antennas Eight Element V2 Multi-Band 8 Circle Receive Array System, intended for 160-, 80- and 40-meter band coverage, with useful functionality from 500 kHz to 15 MHz. The HIZ-PC-8PRO Phasing Controller and system components combine to provide an effective directional receive pattern that is electronically switchable to eight different directions. The Hi-Z Antennas Eight Element V2 Multi-Band 8 Circle Receive Array System provides enhanced signal-to-noise performance with Receive Directivity Factor (RDF) approaching 12dB and up to 35dB array front-to-back! The HIZ-PC-8PRO is the heart of this antenna which provides dramatically improved reception over transmitting antennas. It properly combines signals from eight receive short element active verticals which are each ground-mounted on a ground rod, in a circle. DXE-RSEAV-1 are sold separately, which use DXE-AVA-3 Element Amplifiers. Sharper cardioid patterns with deeper reverse nulls are developed by the 8 Circle than other arrays. This Phasing Controller and other system components provide an effective receive pattern that can be electronically rotated to eight different directions: typically, 45, 90, 135, 180, 225, 270, 315 and 360 degrees. Standard 85 ft. diameter 8 Circle Arrays provide 160-, 80- and 40-meter band coverage with an exceptional cardioid pattern, supported with the updated delay cables HIZ-DL4-60-85 (Long and Short, sold separately). Alternatively, choose HIZ-DL4-80-113 cables (Long and Short, sold separately) for a 113 ft. diameter 8 circle which increases performance on the 160 and 80 meter bands. The HIZ-MDC-8PRO is the required Manual Directional Control Switch Console, sold separately. The HIZ-PC-8PRO also serves as a replacement part for Hi-Z 8 Circle system owners to order Hi-Z PC-8PRO V2 Phasing Controller. See the listing for more information.
Not Yet Reviewed
$649.00
DX Engineering Receive Feedline Voltage Injectors
DX Engineering Feedline Voltage Injectors, DXE-FVI-1, are high-quality bias-tee devices that place direct current onto a receive antenna system's coaxial cable while preventing DC from reaching the Radio port. These FVI-1 voltage injectors are used to power active accessory devices, such remote relays, switching systems, and preamplifiers. These are the original equipment FVI-1 units provided with single DX Engineering Active Receive Vertical antenna models. Voltage is applied via the 2.1mm power connector to the receive antenna feedline F connector. The RCA phono jack connects to the receiver input with that DC voltage blocked, while passing RF from 100 kHz to 30 MHz. Various RCA phono plug adapters for different RF cable connectors are available in Suggested Parts. Two DXE-FVI-1 feedline voltage injectors may be connected at opposite ends of a feedline to provide DC voltage on the transmission line for your own custom application, keeping the input and output RF devices isolated from the voltage. The included 120V AC 60 Hz wall transformer power supply may be connected to the 2.1mm power connector may to place approximately +12 volts DC on the coaxial cable center conductor, with the coaxial cable shield used as the negative ground return. A different station power supply, 1-16 VDC, may be used with an in-line, 1 Ampere, fast-blow fuse for various devices. DX Engineering feedline voltage injectors are ready for your "DC power on the coax" needs! Note: Whenever the DX Engineering "Documentation" tab is available, please look at the associated files for additional product information. When you need to inject a DC voltage onto a 75 ohm coaxial cable used for receiving, remember the DX Engineering Feedline Voltage Injector!
Not Yet Reviewed
$99.99
ELAD ASA15 Amplified Antenna Splitters
ELAD ASA15 Amplified Antenna Splitters are designed to distribute the signal received from one antenna to up to five different receivers simultaneously. They utilize an internal divider and ultra-wideband low-noise amplifiers to ensure the antenna signal is effectively shared across all five outputs. Each of the five outputs can provide either 0dB (no gain) or 12dB gain, which helps compensate for long distribution cable run losses or boost weak signals. Additionally, a 15dB attenuator on the input can be switched on to prevent overload. Upgrade your RX antenna distribution system with the ELAD ASA15 Amplified Antenna Splitter, ensuring reliable and high-quality signal reception across multiple receivers.
( 1 )
$327.99
Unified Microsystems RAS-4 Receive Antenna Switch
Unified Microsystems RAS-4 Receive Antenna Switch is an outdoor capable remote relay unit that allows the operator to select up to four antennas. Receive only antennas are critical for success on the low bands. Due to the wavelengths of the low bands, these antennas cannot be rotated. Several very effective receive only antennas are mono-directional or bi-directional, including Beverage, Reversible Beverage, Beverage on the Ground (BOG), Reversible Beverage on the Ground (RBOG) and many others,. Therefore, a high quality, low noise four port receive antenna switch is required to cover all of the directions with multiple antennas. Common mode noise pick up can ruin the performance of receive antenna systems, so the RAS-4 isolates both the center conductor and shield of unselected ports. An internal bifilar ferrite choke further reduces common mode currents. This unit features female F connectors for RG6U coax with male F connectors, the standard field-serviceable coaxial cable assemblies for receive antenna systems. A very important requirement for dual feedline Reversible Beverage and RBOG antennas is provided by the RAS-4. By default, unselected ports are terminated for 75 ohms. The user can change to 50 ohm, open circuit, or center conductor-shield short by soldering wire jumpers. The RAS-4 is housed in a NEMA rated enclosure with a gasket lid. A cable gland seals the control cable entry. The internal circuit board has a conformal coating for additional protection. The RAS-4 can be mounted outdoors, with the enclosure flanges or with the included L bracket for mounting to a pole or post. The RAS-4 Receive Antenna Switch is a receive-only relay unit that cannot be used for transmitting antennas. The required in-shack control console switch is not included. The RAS-4 will work with a commercial or a simple home brewed, positive 12V One-of-Four switch. Choose from DX Engineering, EA4TX and others for manual or automated switching. Unified Microsystems RAS-4 Receive Antenna Switch Specifications Antenna Selection: 4 receive antennas to 1 main feedline Dimensions: Approx. 4.5 x 3.5 x 3.25 in. (11.4 x 8.9 x 8.3 cm), not including the bracket. Connector type: F (5 total) Unselected port termination: 75 ohm default; 50 ohm; open; shorted. Wire jumper selectable VSWR: < 1.5:1 from 100 kHz to 20 MHz Insertion loss: < 0.4dB from 100 kHz to 20 MHz Port to Port Isolation: > 45dB from 100 kHz to 20 MHz Control Cable: 3 wire plus ground (4 total conductors), Not included Switch Controller: 12 to 14 Vdc, Not included
( 2 )
$124.95
DX Engineering Beverage Antenna System Combos
DX Engineering Beverage Antenna System Combos are single-wire single-direction Beverage antenna feed systems. These combos include DX Engineering's superb receive preamp and the Beverage antenna feedpoint transformer! The included BFS-1 transformer design makes them immune to the strong signal overload and core saturation. The isolated-winding matching transformer significantly increases the signal-to-noise ratio in Beverage and other high-impedance antennas. The included termination resistor is a special 470 ohm, 2 watt, non-inductive resistor that withstands nearby lightning strikes. Also included, the DXE-RPA-2 Modular Receive Preamplifier is the best low noise, receive preamps available… period. It is optimized for the 300 kHz through 35 MHz frequency range with an advanced push-pull amplifier design that eliminates harmonic distortion and it handles strong signals without distortion or overload. The DXE-RPA-2 Modular Preamp features one internal option slot for a plug-in module. Choose from the DXE-RG5000HD-PM Receiver Guard, the DXE-IT-PM 75 to 50 ohm Impedance Transformer, or use a RXFL Filter Adapter and a Receive Filter board for band pass, high pass or low pass filtering. Click "More Detail" for additional information. The "Documentation" tab contains links to associated files. SWLs and Radio Amateurs around the world have come to rely on the exceptional performance of DX Engineering products. Order one of these DX Engineering Beverage Antenna System Combos to get excellent MW and HF reception with your Beverage antenna.. * Important Note regarding DX Engineering Protection Plans and Kit Combo Contents Protection plans cannot be purchased for combination packages or on applicable devices after shipment. DX Engineering Combination Kits and Packages are designed to help you easily visualize and order the right items for your specific needs. However, we encourage you to contact our experienced Technical Sales Team for assistance. We can help adjust the kit contents, suggest substitutions based on stock availability, and offer DXE Protection Plans for radios and devices when applicable. Contact us for Expert assistance and make informed purchasing decisions with our guidance.
Not Yet Reviewed
$385.98
Unified Microsystems Beverage Antenna Transformers
Unified Microsystems Beverage Antenna Transformers are now available. UMS transformers are built with stainless steel hardware and an F-Type coaxial connector. These transformers are fully enclosed for ultimate protection from the elements. They are corrosion resistant and sealed for many years of trouble-free use. Unified Microsystems Beverage transformers should be used with 75 ohm cable, typically RG-6, 6UF, F-6, or equivalent. H. H. Beverage described his "Wave Antenna" (the first Beverage) in the November, 1922 QST Magazine. Beverages are classic designs with well-defined characteristics and time-proven performance. Beverage antennas are among the simplest of high signal-to-noise-ratio antennas to construct. Make Unified Microsystems Beverage Antenna Transformers part of your receive-antenna system. Get yours from DX Engineering today!
( 9 )
$37.95
Chelegance Deshibo GA-450 Active Indoor Shortwave Loop Antenna
Chelegance Deshibo GA-450 Active Indoor Shortwave Loop Antenna – for HF receive from 2.3 to 30 MHz (SW) and AM Broadcast receive from 522 to 1710 kHz (MW). This amazing little mini-loop antenna is less than 8 in. diameter with a control base and BNC loop connector, gain control, USB-C charging port, internal battery and female BNC output. This antenna set includes male BNC-to-BNC and BNC to 3.5mm adapter cables for connection to your receiver—and a USB A to USB C cable to connect charging power from a laptop (AC adapter not included). Completely portable operation is simple with the control base charged battery and/or backup USB power source. This Active Indoor Shortwave Loop Antenna is ideal for use at home, in the camper, or RV. * SPECIFICATIONS: - Frequency range: SW 2.3-30 MHz / MW 522-1710 kHz - Impedance: 50 ohm - Antenna gain: 20 dbi - Ring diameter: 7.874 in. (20 cm) - Control box: 4.172 x 2.559 x 1.024 in. (105 x 65 x 26 mm) - Charging port: USB-C * PARTS LIST: - 1 x Receiving Loop, D-20CM, BNC - 1 x Active Antenna Box with Built-in 18350 battery - 2 x RF cables, 39 in. (1m) male BNC to 3.5mm and BNC to BNC - 1 x USB A to USB C cable
( 6 )
$147.00